steel pipe with an outside diameter of 45 mm carries a hot fluid at 539 K. The pipe is insulated with 10 mm lagg = 0.22 W/m°C) followed by 30 mm of fiber glass insulation (k = 0.07 W/m°C). If the outside insulation temperatu alculate the interface temperature in Celsius between the fiber glass insulation and the lagging material. (Write
Q: The temperature of a cylindrical tank containing liquid nitrogen is -10°C. Tank diameter is 16 cm.…
A: Given data: Here, Ts represents the liquid temperature, d represents the diameter, Q̇ represents…
Q: As seen in the attached figure, a 5-mm-diameter spherical ball (k = 15 W/m·K, Cp=480 J/kg·K) at 50°C…
A: Given : The diameter of spherical ball = 5 mm The thickness of the insulation = 1 mm The heat…
Q: Steam at a temperature of 723 K is flowing through a pipe with an outer diameter of 100 mm. The pipe…
A:
Q: Steam at a temperature of 723 K is flowing through a pipe with an outer diameter of 100 mm. The pipe…
A:
Q: 1. Find the surface temperature of a 15 cm outside diameter pipe wrapped with 6 cm of 85% magnesia…
A: There are three mode of heat transfer : conduction, convection and radiation. heat transfer due to…
Q: HEAT TRANSFER A mild steel steam pipe with an outer diameter of 11.43 cm and inner diameter of…
A:
Q: A 0.5-m-diameter pipe (ɛ = 0.9) carrying steam has a surface temperature of 500 K (see Fig. 1.25).…
A: Given data as per question surface temperature =500 k Room temperature =300 k convective heat…
Q: An insulation covers a spherical vessel whose diameter is 1 meter. The insulation has a k value of…
A: Given data :- K = 17 w/m°C Q = 500W D = 1 m
Q: there are times when contact resistance between two surfaces is so small compared to the overall…
A: Given that there are times when contact resistance between two surfaces is so small compared to the…
Q: A person is found dead at 5 PM in a room whose temperature is 20 °C. The temperature of the body is…
A: Given data: The room temperature is T∞=20°C The temperature of the body is T=25°C The normal…
Q: A 50-cm-dometer spherical tank is fine, with iced water at 0°C The tank is thin-shelled and Rs…
A: Given data Diameter of the tank is D=50 cm Thermal conductivity of the glass wool is k=0.05 W/m-K…
Q: Clothing made of several thin layers of fabric with trapped air in between, often called ski…
A: Consider the thermal circuit shown below for the 5 layered jacket. Here, The total resistance for…
Q: A 3-layered composite wall is consists of different materials. Inside is wall 1: 300 mm thick, k =…
A: Given: K1=1.5w/m-k L1=300mm=0.3m K2=3.5w/mk L2=0.2m K3= thermal conductivity of third wall L3=0.1m…
Q: A 6-mm-diameter electrical transmission line carries an electric current of 50 amperes and has a…
A: Given- parameter given- diameter= 6mm current= 50A resistance= 0.002ohm/mt. length k=218w/m-k
Q: A thick-walled tube of stainless steel [ K=19 W/ m-ºC]. with 2-cm inner diameter (ID) and 4-cm outer…
A:
Q: 03-As shown in the figure, four circumferential fins of aluminum rectangular profile are installed…
A:
Q: A current of 200 A is passed through a stainless-steel wire [k=19 W/mK] 3 mm in diameter. The…
A:
Q: An electronic component with dimension of 5 cm wide, 6 cm high, and 9 cm long is cooled by aluminum…
A: Fins are used to improve heat transfer from surfaces in a variety of applications. When the…
Q: of 60 W/m-K. The pipe is used for transporting nanocoolant at an average temperature of 70 °C and…
A:
Q: Inconel refers to a class of nickel-chromium-based superalloys that are used in high-temperature…
A:
Q: A body having a cylindrical shape of length equals to 1.9 m and diameter equals to 400 mm is inside…
A: Given:Length of the cylinder, L=1.9 mDaimeter, d=400 mm or 0.4 mRadius, R=0.2 mAmbient temperature,…
Q: What is thermal conductivity? How the thermal conductivity of Solid, liquid and gases are varying…
A: Thermal conductivity is defined as the ability of a material to conduct the heat or temperature…
Q: 8 A copper hot-water cylinder of length 1-0m and radius 0-20 m is lagged by 20m of material of…
A: Given: Length of the pipe (L)=1mRadius of the pipe=0.20mThickness of the lagging (t)=0.020mHeat…
Q: Q3/A 10-cm length of platinum wire 0.5 mm in diameter is placed horizontally in a container of air…
A: To find: The surface temperature. Given: The length of platinum wire is l=10 cm. The wire diameter…
Q: An aluminum plate and a stainless steel plate are pressed against each other at an average pressure…
A: For the same heat transfer rate & area we get :
Q: A long aluminum cylinder with a diameter of 5 cm is initially at a temperature of 200°C and is…
A:
Q: A 10 cm diameter cylindrical bar, heated in furnace to a uniform temperature of 2000 C, is allowed…
A: given; diameter(d)=10cm =0.1m temperature of surroundings(T1)=2000cenviornment…
Q: conduction convection experiment If the material of the fins can be changed to reduce the total…
A:
Q: Determine the temperature at the base of the shaft (where it connects to the motor. A shaft from a…
A: Friends are the projection proturding from a hot surface into ambient air and they are meant for…
Q: 2. A composite furnace wall is made up of a 14 in. lining of magnetite refractory brick, a 5.3 in.…
A: Given data as per the question The thickness of brick =14 in The thickness of magnesia =5.3 in The…
Q: What is the fin effectiveness of a rectangular plate fin made of aluminum O.3 mm thick mounted on a…
A:
Q: The engine cylinder of a motorcycle is constructed of aluminum alloy ((T= 400 Kk 186 W/m. K) and is…
A: Given Data : k = 186 W/mK Height H = 0.15 m Outside diameter d = 50 mm radius r = 25 mm Outside…
Q: A 6 cm diameter cylinder is initially at a temperature of 10 °C. Later, this cylinder was thrown…
A:
Q: The emissivity of galvanized steel sheet, a common roofing material, is ε = 0.13 at temperatures…
A: Write the emissivity of common roofing material. ε=0.13 Write the absorptivity of solar radiation.…
Q: The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm…
A:
Q: Required information A 16-m x 8.5-m section of wall of an industrial furnace burning natural gas is…
A: Given data as per question Temperature of surface room=300cTemperature of outer surface of this…
Q: Q3/ A 10-cm length of platinum wire 0.5 mm in diameter is placed horizontally in a container of air…
A:
Q: The piston cylinder of a motorcycle engine is constructed of AISI 316 stainless steel, having a…
A: solution: The value of thermal conductivity of AISI 316 stainless steel as 15 W/m.K The heat…
Q: The heat loss from a fin is 6W. The effectiveness and efficiency of the fin are 3 and 0.75…
A: Given:Qf=6 Wε=3η=0.75
Q: Calculate the heat transfer rate from a single-pane glass window with aninside surface temperature…
A: The law which describes the rate of heat transfer in conduction is known as Fourier's Law. According…
Q: In the design of electronic components, it is very desirable to attach the electronic circuitry to a…
A: Write the properties of different materials of the substrate.1. Alumina/Aluminum Oxide (Al2O3): its…
Q: Hot engine oil is being transported in a horizontal pipe (k = 15 W/m∙K, Di = 5 cm) with a wall…
A: Assumptions Thermal conductivity of pipe and insulation will not vary with temnperature. steady…
Q: The temperature of a tank in the form of liquid nitrogen is -10 ° C. Tank diameter is 16 cm. The…
A: T = -10°C = 263 K D = 16 cm = 0.16 m Q/L = 65.5 W/m h = 4.35 W/m2.K e= 1
Q: A cast iron pipe (k = 80 W/m - oC) whose inner and outer diameters are 5 cm and 5.5 cm respectively…
A:
Q: How does a fin enhance heat transfer at a surface?
A: Fins are the projections or extended surfaces protruding from hot surface into ambient fluid and…
Q: . A hollow sphere with an outer diameter (d,) of 4 cm and outer diameter of 12 cm is kept at an…
A:
Please solve this question, Thank you very much
Step by step
Solved in 2 steps with 2 images
- The heat conducts through the shape below. The temperature of the right face is 93 °C, while the left face is at 23 °C. If the top and bottom faces are completely insulated, and the thermal conductivity of the material decreases with decreasing temperature. * Assume that the thermal conductivity is 100 at 23, decreased to 10 at 93. A) Sketch the temperature profile inside the plate. B) If both sides of the plate in the above problem is exposed to air: Left side (h = 20 W/m2K, TL = 20 °C) and right side (h = 90 W/m2K). Calculate the temperature of the air on the right side.Steam at a temperature of 723 K is flowing through a pipe with an outer diameter of 100 mm. The pipe is insulated with 30-mm thick mineral wool, the average thermal conductivity of which is 0.065 W/m.K. Determine the outside surface temperature of mineral wool if the ambient air temperature is 300 Assume the hot-surface temperature of the mineral wool is the same as that of the flowing steam and the value of the surface coefficient of the insulating material is 33 W/m2.K.The cylindrical pipe with a thread diameter of 0.070 m and an internal diameter of 0.050 m is insulated both internally and externally. Calculate the heat loss per unit length of the pipe (1 m) when the inner surface temperature of the pipe is kept at 50 °C and the outer surface temperature at 20 °C (Average thermal conductivity constant = Km= 0.172 J/cm.s.K).
- Question 1: A glass window of width W = 1 m and height H = 2 m is 5 mm thick and has a thermal conductivity of kg =1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15 oC and -20 oC, respectively, on a cold winter day, what is the rate of heat loss through the glass? To reduce heat loss through windows, it is customary to use a double pane construction in which adjoining panes are separated by an air space. If the spacing is 10 mm and the glass surfaces in contact with the air have temperatures of 20 oC and -15 oC, what is the rate of heat loss from a 1 m x 2 m window? The thermal conductivity of air is ka = 0.024 W/m.K.A horizontal pipe having a surface temperature of 67 °C and diameter of 20 cm is buried at a depth of 1 m in the earth at a location where k = 1.8 W/m-°C. The earth surface temperature is 15 °C. Calculate the shape factor if the pipe length is 10 m.Consider a two-layer sphere with inside fluid convection rate h1 and outer rate h2. The first layer has inside radius r1 and outside radius r2. The second layer has outside radius r3. What is the general equation for the total resistance? Neglect thermal contact resistance.
- A fluid has a temperature of 100C and thermal film coefficient of 50 W/m^2-K. Solve for the heat transferred per sq m of contact if the surface it is in contact with has a surface temperature of 20C.In addition , the space between the upper cap, the lower cap, and the cylindrical wall is filled with linear insulating material of permeability u.Metal vapor pipe with an outer diameter of 30 mm has a surface temperature of 400 k and will be insulated with an insulation of 20 mm thickness and k = 0.08 w / m ^ 2.k. The pipe is exposed to air at 300 k and 30w / m ^ 2.k. has convection coefficient. calculate the critical radius and heat loss
- What is the rate of heat transfer, temperature gradient, and the direction of the heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? - thermal conductivity of Celotex in AES = 0.028.Question 1: A glass window of width W = 1 m and height H = 2m is 5 mm thick and has a thermal conductivity of kg =1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15 °C and -20 C, respectively, on a cold winter day, what is the rate of heat loss through the glass? To reduce heat loss through windows, it is customary to use a double pane construction in which adjoining panes are separated by an air space. If the spacing is 10 mm and the glass surfaces in contact with the air have temperatures of (last two digit of your Registration number) °C and -15 °C, what is the rate of heat loss from a 1 mx2mwindow? The thermal conductivity of air is ka = 0.024 W/m.K.In order to reduce the heat loss through a large furnace wall, the decision has been made to add external insulation. Calculate the thickness of insulation required to reduce the heat loss by 75%. Before the change is made, no outer steel shell is used.Data: Refractory brick and wall brick:k = 0.87 W m-1 K-1Insulation: k = 0.090 W m-1 K-1•Steel: k = 43 W m-1 K-1h = 55 W m-1 K-1 (inside furnace).h = 11 W m-1 K-1 (outside furnace).