Suppose a bicycle is traveling at a speed of 14 mps. The bicycle chain connects 2 gears, one attached to the wheel and one attached to pedals the radius of the wheel is 10 inches, and radius of the gear attached to the wheel is 1.5 inches. If the radius if the gear connected to a pedal gear with radius of 4 inches. find the angular velocity of the pedal gear in radians per second

Suppose a bicycle is traveling at a speed of 14 mps. The bicycle chain connects 2 gears, one attached to the wheel and one attached to pedals the radius of the wheel is 10 inches, and radius of the gear attached to the wheel is 1.5 inches. If the radius if the gear connected to a pedal gear with radius of 4 inches. find the angular velocity of the pedal gear in radians per second

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter12: Rotation I: Kinematics And Dynamics

Section: Chapter Questions

Problem 60PQ

See similar textbooks

Similar questions

Given the disk and density in Problem 11, derive an expression for the rotational inertia of this disk around an axis at theedge of the disk and perpendicular to the disks surface.
A potters wheel rotates with an angular acceleration = 4at3 3bt2, where t is the time in seconds, a and b areconstants, and has units of radians per second squared. Theinitial position of the wheel is 0 and the initial angular velocityis 0. Obtain expressions for the angular velocity and the angular displacement of the wheel as a function of time.
A flywheel turns at 480 rpm. Compute the angular speed at any point on the wheel and thetangential speed 30 cm from the center.
For the system given in the figure, the radius of the gear isgiven as 15cm and it rolls on the horizontal rack. The pin Gat the center of the gear is located inside a slot arm AB,which rotates at a constant angular velocity of ? = 5 rad/sin clockwise direction. Determine the angular accelerationof the gear and the total acceleration of the pin G when ? =50°.
A 255-lbf block is suspended from an inextensible cable which is wrapped around a drum of 1.75-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of inertiaI̅= 12 lb . ft . s 2 . At the instant shown, the velocity of the block is unknown directed downward. Knowing that the bearing at A is poorly lubricated and that the bearing friction is equivalent to a couple M of magnitude 65 lb .ft, determine the velocity of the block before it has moved 3.5 ft downward if at S2 speed is 13.5ft/s. (The final answer should be in two decimal places with correct units)
An electric motor rotating a workshop grinding wheel at a rate of 151rev/min is switched off. Assume constant angular deceleration of magnitude 2.93 rad/s2. Through how many revolutions does the wheel turn before it finally comes to rest?
Gear A Radius = 0.06 m Gear B Radius = 0.3 m Gear C Radius = 0.36 m Note that the Load is Connected to Gear B The system shown starts from rest at t = 0 and accelerates uniformly. Knowing that at t = 4 seconds the velocity of the load is 4.8 m/s downward, determine the angular acceleration of gear A.
Assume that you have a thin walled loop of radius 11.0 cm, which starts at rest and rolls down a ramp. The angular velocity of the loop, when it reaches the base of the ramp is 14.5 rad / s. What was the initial height from which the loop started to roll? (Provide your answer in metres to 3 decimal places but do not include the units.)
In the figure above, block M2 = 20 kg is on a ramp of theta = 25 degrees and the coefficient of friction, μk, between the M2 and the ramp is 0.20. It is connected via a massless chord to block M1 via a pulley as shown in the figure. The block M1 = 40 kg is hanging from the chord and is descending with acceleration a. The pulley can be considered as a solid disk of mass Mp = 6 kg and radius R = 12 cm. What is the acceleration with which M1 is descending?
The flywheel turns clockwise with a constant speed of 690 rev/min and the connecting rod AB slides through the pivoted collar at C. For the position ? = 59°, determine the angular velocity ?AB of AB by using the relative velocity relations. (Suggestion: Choose a point D on AB coincident with C as a reference point whose direction of velocity is known.)
If the beaters on a Mixmaster make 700 revolutions in 2 minutes, what is the average rotational speed of the beaters? Express your answer in both revolutions per minute and revolutions per second.rev/minrev/s
The initial angular velocity of the propeller of the boat is 80 rev/min and was increased to 120 rev/min. What is its angular displacement if it accelerates at 4.50 radian per square second?