Suppose an iceberg is shaped as a solid circular cylinder of arbitrary diameter, such that it floats as illustrated in Figure 1. If the cylinder extends 2 m above the free surface of the ocean, determine the depth of the cylinder (b) below the free surface of the ocean. Consider that the density of the ocean water is Pa = 1024 kg/m3 and the density of the iceberg ice is Ph = 935 kg/m3. Additionally, make a descriptive analysis on the stability of the mechanical equilibrium state of the iceberg, if a normal force is applied on one edge of the top cap of the iceberg, consider cylinder radi less than 2 m and greater than 2 m. 2m

Suppose an iceberg is shaped as a solid circular cylinder of arbitrary diameter, such that it floats as illustrated in Figure 1. If the cylinder extends 2 m above the free surface of the ocean, determine the depth of the cylinder (b) below the free surface of the ocean. Consider that the density of the ocean water is Pa = 1024 kg/m3 and the density of the iceberg ice is Ph = 935 kg/m3. Additionally, make a descriptive analysis on the stability of the mechanical equilibrium state of the iceberg, if a normal force is applied on one edge of the top cap of the iceberg, consider cylinder radi less than 2 m and greater than 2 m. 2m

Name: Only need help with the analysis on the stability of the mechanical e
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Only need help with the analysis on the stability of the mechanical equilibriumSuppose an iceberg is shaped as a solid circular cylinder of arbitrary diameter, such that it floats as illustrated in Figure 1. If the cylinder extends 2m above the free

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
Differential equations A cylinder of 10 cm radius and 15 cm height has a weight of 19.6 N, if the cylinder is vertically immersed en a fluid with a density of 2.5g/cm3 a. Determine if the cylinder floats and if this is the case which serıa the length of the cylinder that is submerged in water. b. If the cylinder is pulled 5 cm upwards from its equilibrium position and released, determine the motion equation for the cylinder. Pls dont skip steps
The density of a steel anchor is 4205 kg/cu.m that is attached to a cylinder with 0.60m diameter, height of 1.2m, and with a mass of 34kg that floats in water with its axis vertical(upright). The steel anchor is attached to the cylinder which causes it to be submerged to a depth of "h" meters and remain in equilibrium position. a) Determine the equation based on the relationship between the weight of the anchor, "Wa" and the submerged depth "h". (Show step by step solution)
A piece of steel wire, which is 3 m long, and of 1 mm diameter hangs vertically from the ceiling. A 5 kg mass, made from iron, (density = 7,9 x 103 kg.m-3 ) is attached to the free end. Find the tension in the wire when the mass is completely submerged in the water. (Density of water = 1 000 kg.m-3 )
The uniform control gate AB shown is pinned at A and rests on the smooth surface at B. The gate has a width of 1m. If the gate has a mass of 3.9 Mg, determne the maximum depth of water h in the reservoir that will cause the gate to be on the verge of opening.
A ring weighs (83.327×10^-4) N in air and (80.33×10^-4) N when submerged in water: 1. What is the volume of the ring? 2. What is the density of the ring? 3. What is the ring made of?
Determine the total force in kN on a circular plate of diameter 1.5 m which is placed vertically in water in such a way that center of the plate is 2 m below the free surface of the water. Include the diagram in your solution. a.103.0 b.59.34 c.44.14 d.35.67
A cylindrical tank contains 1.0m of mercury (SG-13.6) and 3.0m of water. To look into the tank. a viewport measuring 0.60m by 0.60m was installed 0.60m above the base of the tank as shown in the figure. (a) using the pressure prism concept. determine the total force (in kN) acting on the view port due to water. (b) using the pressure prism concept. determine the total force (in kN) acting on the view port due to mercury. (c) What is the total force acting on the view port in KN? (The total force acting on the view point is equal to the sum of the component forces due water and mercury.)
A block of wood floats in water with 45 mm projecting above the water’s surface. When placed in glycerine of Relative Density (RD) 1.34, the block projects 70 mm above the surface of that liquid. Determine the density of the wood
If the plate is replaced with a vertical triangular plate (base = 5ft and height = 12ft) where its base is submerged by 12ft below the water surface, determine the location of the hydrostatic force and center of pressure. Answer is 23,920 lbf and 15.6957ft
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown in Fig. below. The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B. Determine the force exerted on the plate by the ridge.
A plate in the shape of an isosceles right triangle with side length 4 meters is submerged in water sothat its hypotenuse is facing down, and its right angle vertex is level with the surface of the water. Findthe hydrostatic force on one side of the plate. How can I properly set up the intergral. I thought the answer should be about 147929 N but I could be wrong.