Suppose the transfer function of a feedback control system is Y(s) R(s) s2+ags+a4 The unit step response of this system is: y(t) = [1 – e at(-3.1t + 1)]u(t) If the settling time is 4 seconds and P.O.> 0, answer the following questions: 1. The value of a = 2. The value of the peak time seconds

Suppose the transfer function of a feedback control system is Y(s) R(s) s2+ags+a4 The unit step response of this system is: y(t) = [1 – e at(-3.1t + 1)]u(t) If the settling time is 4 seconds and P.O.> 0, answer the following questions: 1. The value of a = 2. The value of the peak time seconds

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A robotic system with transfer function ?(?) =(100)/(s(0.1s+1)(0.1s +1)) is controlled with gain K as shown in the figure. A)To analyze the frequency response of this system, draw the Nyquist graph. B)Apply the Nyquist stability criterion. C)Verify the stability analysis you made in part (b) by plotting root locus plots for the positive and negative values of the K gain. D)Calculate the gain value that makes this system borderline stable and show it on Nyquist and Root locus graphs. E)Calculate the gain margin, phase margin, gain crossover frequency and phase crossover frequency values. F)Explain whether the system is stable over the gain margin and phase margin values. WE NEED TO SOLVE THE PROBLEM IMMEDIATELY. PLEASE HELP.
Consider a closed-loop system with a zero-order hold. Consider G,(s) =400/(s^2+400) Determine the closed-loop transfer function T(z) for the system at T=1 sec.
4. The front end of a television receiver, having a bandwidth of 7 MHz andoperating at a temperature of 27° C, consists of amplifiers having a gain of 15, followed by a mixer whose gain is 20. The amplifier has a 300Ω input resistor and a shot noise equivalent resistance of 500Ω . For the mixer; these values are 2.2kΩ and 13.5 kΩ, respectively, and the load resistance of the mixer is 470 kΩ. Calculate the equivalent noise resistance for this television receiver.5. A receiver connected to an antenna whose resistance is 50Ω has an equivalent noise resistance of 30Ω. What is the receiver’s noise temperature?
Consider a closed loop system with zero order hold.consider Gp(s)=400/s2+400.determine the closed loop transfer function T(z) for the system at T=1sec
Consider a stable LTI system with input x(n) and output y(n). The zero-pole pattern of y(n)consists of a double zero at the origin of the z-plane and the poles 3 ± 3j. The zero-pole pattern ofx(n) consists of a double zero at the origin of the z-plane. Find the system function and the systemimpulse response.
Open loop transfer function G( s ) = K/ s(s+3)(s+4) for a systema) using the Routh Hurwitz criterion, the poles of the closed loop system are purely imaginary calculate the value that K will get so that it has roots on the axis.b) calculate the maximum value that K will receive so that the system can be stablec) calculate the values that K will get so that the system can have roots at -1 on the real axis
1. Finding the closed loop transfer function of the system2.What is the steady state error of the system when a unit ramp signal is applied to its input?3. Given Km=5 and Kb=0.01, what should be the K value for a steady-state error to occur at the unit ramp input of the system?
Given a plant P(s)=−3s+1s+a and a model for measureable output disturbance d with transfer function Q(s)=1s+b. Compute the DC feedforward solution uP=u+Fd, where u is the feedback control, F is the feedforward gain, abd uP is the plant input, when a = 4.3 and b = 3 (use 2 decimals).
A car was ignited & a signal from the engine i.e a(z) was passed through a cascade of 2 passive RC lowpass filters to generate an output signal, b(z).a.Show a differential equation derivation to describe the systemb.Make a sketch utilizing circuit diagramc.Mention if the RC system in question above isi.Time in-variant / Time variant ii.Non linear / lineariii.Non-invertible / Invertibleiv. Non-causal / Causal v. Have no memory / Have memory sytems.d. d2b(z)/dz2 + 3(db(z)/dz) +2b(z) = 3(da(z)/dz) +2a(z)Let's assume that the d.e(differential equation) above is that which is characterised by the RC system in the main question above.Where a(z) & b(z) is the input & output of the RC system respectively.Considering an impulse of a(z)=δ(z) is applied to the system, determine the output b(z) of the system
An Armstrong modulator is used to generate FM which is suitable for FM broadcasting.You are given input of narrowband FM signal with carrier frequency fc1 = 27 MHz anda frequency deviation Δf1= 17 kHz. Assume that the frequency multiplier with n = 3 andlocal oscillator frequency of 80 MHz. Calculate the output of the carrier frequency andfrequency deviation if additive frequency is selected by mixer. Explain your obtainedanswer.
By a suitable graphical representation sketch signal voltage (V) against period (t) of an FM System at t ranges from 1sec to 12sec. Taken magnitude of signal voltage to be 10V, 2pifc = 10*108, 2pifm = 3000, carrier deviation is 2.337KHz. please step by step solution. You are required to show work
1. Given an analog signal x(t)=10 cos(2π.5500t)+5 cos(2π.7500t) is sampled at a rate of 8,000 Hz, a. Sketch the spectrum of the sampled signal up to 20 kHz; b. Sketch the recovered analog signal spectrum if an ideal low pass filter with a cutoff Frequency of 4 kHz is used to filter the sampled signal in order to recover the original signal; c. determine the frequency/frequencies of aliasing noise.