PROBLEM 9.3. A signal æ( t) is sampled with sampling rate fs, and the resulting sampled sequence x[n] is converted back to continuous time using an ideal DAC having the same f, parameter: 2(t). |r[n] ADC v(t) DAC f. sin (440rt) sin (420nt) sin (400rt) Suppose that æ(t) = and y(t) = A nt nt (a) Find A. (b) Find B. (c) Find f.

PROBLEM 9.3. A signal æ( t) is sampled with sampling rate fs, and the resulting sampled sequence x[n] is converted back to continuous time using an ideal DAC having the same f, parameter: 2(t). |r[n] ADC v(t) DAC f. sin (440rt) sin (420nt) sin (400rt) Suppose that æ(t) = and y(t) = A nt nt (a) Find A. (b) Find B. (c) Find f.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Assume that the signal to be measured is displayed in the following form. y(t)=5sin1000t mV The time constant of the 1st order device is 100ms, K=1 V/V and its output is transferred to the 2nd order amplifier. The natural frequency and damping ratio of the amplifier is 15,000Hz and 0.8, respectively. Then, determine the expected output signal of y(t). And calculate the dynamic error and phase delay on the output. Is the chosen metrology system reasonable? If not, suggest a way.
A hard disk drive (HDD) is an electro-mechanical data storage device that stores and retrieves digital data using magnetic storage and one or more rigid rapidly rotating platters coated with magnetic material. Figure 1 shows a simplified block diagram of a HDD. For analysis purposes, given gain K=30 and G(s)=1 / s(s+4) determine the open-loop and closed loop poles of the HDD and plot these separately in the S-Plane. Also discuss the stability using two different approaches.
b) G(?)=K [(S−1)(S−2) / (S+2)(S+3)] ; Construct nyquist curves for K=1, 5/3, 9 values. Write down the Nyquist stability criterion and explain whether the system is stable or not. c) Define the gain and phase margin, this time on the nyquist curve.
Show that the derivative of a 1-D signal, I=I(x), amplifies the higher frequency components of the signal. Then, prove that even a slight amount of noise n=n(x), can be responsible for a large difference between the derivative I and I+n (Hint: Assume that n can be written as εsin(ωx) for some very small ε and very large ω).
control systems In the electromechanical system given below, it can be seen that the coil can be represented by the series R-L circuit and also the coil It is known that the electromagnetic pulling force (F) is also proportional to the coil current, that is, F = βi. The input of the system is the voltage v applied to the coil and the output is the x path taken by the core. Accordingly, the system find the differential equations and transfer function
1. Finding the closed loop transfer function of the system2.What is the steady state error of the system when a unit ramp signal is applied to its input?3. Given Km=5 and Kb=0.01, what should be the K value for a steady-state error to occur at the unit ramp input of the system?
An exponential signal has initial value Vi=v(0)=-3[V], final value Vf=(∞)=6[V], and a time constant of 10s. Determine: a) the equation for v(t) b) Graph the function for 0≤t≤100 sec, together with a table of values at 10s (or less) time intervals.
100 y(t)+ y (t) = X(t) for a system defined by a first-order differential equation:a. Draw the log magnitude(dB)-log frequency graph of H (jw) (phase graph is not requested. it is expected that the frequency axis will also be logarithmic when plotting the log magnitude graph).b. If the magnitude of H(jw) is -40 dB, it is assumed that the input is suppressed. it is given that the signal X (t) = coswat is suppressed by this system. What is the smallest wa value in this case?
1. Since this is a first order system, provide expression for the time constant. 2. Provide a state space representation of the system. 3. Obtain the transfer function of the system using the state space model. 4. Determine the control gain Kp that results in steady-state error of 0.1
For the system defined by the first-order differential equation 100y'(t) + y(t) = x(t). a) Plot the log magnitude (dB)-log frequency graph of H(jw). b) The input is assumed to be suppressed when the magnitude of H(jw) is -40 dB. It is given that the x(t)=coswat signal is suppressed by this system. What is the smallest wa value in this case? Subject: Signals and Systems
Given the linear mechanical system below:Determine the transfer function ?3(?)/?(?). Express your answer as a single fraction andarrange the degree of variables in descending order.
Let's consider a communication system where four signals with different frequencies (f1,f2,f3 and f4) are combined to form a composite signal. The composite signal is represented by the equation: