Suppose you start an antique car by exerting a force of 350 N on its crank for 0.16 s. Randomized Variablesf = 350 N t = 0.16 s d = 0.22 m What angular momentum is given to the engine if the handle of the crank is 0.22 m from the pivot and the force is exerted to create maximum torque the entire time?

Suppose you start an antique car by exerting a force of 350 N on its crank for 0.16 s. Randomized Variablesf = 350 N t = 0.16 s d = 0.22 m What angular momentum is given to the engine if the handle of the crank is 0.22 m from the pivot and the force is exerted to create maximum torque the entire time?

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter9: Momentum And Its Conservation

Section: Chapter Questions

Problem 1STP

See similar textbooks

Similar questions

Shown below is a small particle of mass 20 g that is moving at a speed of 10.0 m/s when it collides and sticks to the edge of a uniform solid cylinder. The cylinder is free to rotate about its axis through its center and is perpendicular to the page. The cylinder has a mass of 0.5 kg and a radius of 10 cm, and is initially at rest. (a) What is the angular velocity of the system after the collision? (b) How much kinetic energy is lost in the collision?
A satellite is spinning at 6.0 rev/s. The satellite consists of a main body in the shape of a sphere of radius 2.0 m and mass 10,000 kg, and two antennas projecting out from the center of mass of the main body that can be approximated with rods of length 3.0 m each and mass 10 kg. The antenna’s lie in the plane of rotation. What is the angular momentum of the satellite?
A long, thin rod of mass m = 5.00 kg and length = 1.20 m rotates around an axis perpendicular to the rod with an angularspeed of 3.00 rad/s. a. What is the angular momentum of therod if the axis passes through the rods midpoint? b. What is theangular momentum of the rod if the axis passes through a pointhalfway between its midpoint and its end?
A wad of sticky clay with mass m and velocity vi is fired at a solid cylinder of mass M and radius R (Fig. P10.75). The cylinder is initially at rest and is mounted on a fixed horizontal axle that runs through its center of mass. The line of motion of the projectile is perpendicular to the axle and at a distance d R from the center. (a) Find the angular speed of the system just after the clay strikes and sticks to the surface of the cylinder. (b) Is the mechanical energy of the claycylinder system constant in this process? Explain your answer. (c) Is the momentum of the claycylinder system constant in this process? Explain your answer. Figure P10.75
Suppose you start an antique car by exerting a force of 250 N on its crank for 0.34 s.Randomized Variablesf = 250 Nt = 0.34 sd = 0.36 m What angular momentum is given to the engine if the handle of the crank is 0.36 m from the pivot and the force is exerted to create maximum torque the entire time?
The radius and mass of the plastic disk-shaped pulley are measured to be 28 mm and 14 g, respectively. The radius and mass of the metal cylinder are measured to be 18 mm and 480 g, respectively. The moment of inertia of a disk or cylinder for the axis of rotation in the apparatus is given by I = ½ MR2, where R and M are the radius and mass of the disk or cylinder, respectively. Given the above measured values, calculate the moment of inertia of the pulley+cylinder about the axis of rotation in units of kg-m2.
Each object is composed of identical thin sticks of uniformly distributed mass 4.47 kg and length 0.489 m. What are the moments of inertia ?A , ?B , ?C , and ?D of the objects about a rotation axis perpendicular to the screen and passing through the black dot displayed on each object?
A square metal plate with mass M = 1. 20 [kg] and side length 0.180 [m] is pivotedabout an axis through point O at its center and perpendicular to the plate. Threeforces of magnitude F1 = 18. 0 [N], F2 = 26. 0 [N], and F3 = 14. 0 [N] act on theplate as shown. a. What is the net torque on the square plate due to these forces? b. What is the angular acceleration of the disk? The moment of inertia for a plate of lengtha and width b rotating about its center is Icom = 1⁄12 M(a^2 + b^2). c. If the plate is initially at rest, what is the angular velocity of the particle after 3. 00 [s]?
A 2.0 kg particle is traveling clockwise in a circular path with a radius of 1.0 m with a velocity 5.0 m/s. What is the angular momentum of the particle about the origin? (i is the unit vector in the direction of the +x axis, j is the unit vector in the direction of the +y axis, k is the unit vector in the direction of the +z axis)
A particle is acted on by two torques about the origin: t1 has magnitude of 2.0 Nm and is directed in thepositive direction of the x axis. t2 has a magnitude of 4.0 Nm and is directed in the negative direction ofthe y axis (note the bold face of the torques indicates that they are vectors).Find dl/dt, where l is the angular momentum vector of the particle about the origin.
The four masses shown are connected by massless, rigid rods. The masses are mA = 0.125 kg, mB = 0.235 kg, mC = 0.335 kg, mD = 0.404 kg, a. What are the coordinates of the center of mass? xcm = ycm = b. Find the moment of inertia about an axis that passes through mass A and is perpendicular to the plane of the image. IA = c. Find the moment of inertia about an axis that passes through mass D and is perpendicular to the plane of the image. ID =
A 35kg wheel is off-center, with its axle 3.4cm away from its actual center of mass, and it has a radius of 24cm. 84J of work goes purely into speeding it up from rest to 11.3 rad/s. What is the moment of inertia of the wheel?Do not actually solve the problem numerically or algebraically, just pick the one equation and define the relevant knowns and single unknown.