Symbol Value L 524 mm D 3.00 mm A 7.069 mm2 What percentage changes in the computed values of V, I, f, v, and Re would you expect from: a. An error of 1.0 mm in measurement of L. b. An error of 0.03 mm in measurement of D. V, I, f, v, and Re = Average Flow Velocity, Hydraulic gradient, Friction Factor, Velocity, Reynolds Number-

Symbol Value L 524 mm D 3.00 mm A 7.069 mm2 What percentage changes in the computed values of V, I, f, v, and Re would you expect from: a. An error of 1.0 mm in measurement of L. b. An error of 0.03 mm in measurement of D. V, I, f, v, and Re = Average Flow Velocity, Hydraulic gradient, Friction Factor, Velocity, Reynolds Number-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1Two water pumps are arranged in series. The performance data for both pumps follow the parabolic curve fit Havailable =H0 =aV ^2. For pump 1, H0 =5.30 m and coefficient a =0.0438 m/Lpm^2; for pump 2, H0 =8.70 m and coefficient a =0.0347 m/Lpm^2. In either case, the units ofnet pump head H are m, and the units of capacity V are Lpm.Calculate the combined shutoff head. Complete Answer, thank you
Data: Hp2,3 = 2 m; A3 = 20 cm²; A₂ = 1 cm²; Hp0,1 = 0.8 m; NB= 74%(pump efficiency) To determine: a) the flow (L/s); b) the area of section (1) (cm³); c) the power supplied by the pump to the fluid.
On a single plot, show curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure should be 0 to ~1 MPa). Pipe inner diameter: 0.03 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
If the difference between the total pressure and static pressure in an air duct is measured by a pitot tube to be 6.5 cm H2O, what is the flow velocity in m/s? Density of water is 998 kg/m3, and g = 9.81 m/s2. 3 signififcant figures answer
The head-discharge relationship for a certain pump can be represented by the equation H-29-6Q^2 The pump is fixed 2 m shove the water surface tank at a level 10 m above the pump. The suction and delivery pipes are 12 m and 720 m long, respectively and each pipe is 0.5 m in diameter. The Estimate the discharge (in m³/s) at the best operating point for the pumping system,
Gasoline specific mass: 0,82 g/cm3Diameter 1 = 150mmDiameter 2 = 100mmCalculate the volumetric flow rate through a pipe, considering the results in:a) Bourdon Tubeb) Differential Manometers
choose the correct answer Q1A- If the viscose force is dominate in Reynolds number, the flow will be: * a) Laminar flow b) Turbulent flow c) Transition flow d) All the answers Q1B- Chézy and manning equations are controlled in design of : * a) Water pipes network b) Open channels c) Water jet applications d) None of all above
1. Bernoulli Equation on Pump: Water is being pumped from the lower reservoir to the upper reservoir, as shown in the figure. Water is being pumped from the lower reservoir to the upper reservoir, as shown in the figure. Determine the pump horsepower required, given the following data:Q = 23 ft3/sD = 24 in.Ηpump = 75 %Ltotal = 3600 fthpipe = head loss coefficient = 0.0076 ft/total pipeline length ft show Complete Solution/s (i.e. transformations, equivalent formula, etc).
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa
Water flows through a pipe at 15 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3 kPa are measured for P1, P2 and p3, respectively, what are the head loss between 1-3 in meters.
An aqueduct is required to supply water to the community.Data: Families = 12 Average members per family = 3 people Breakfast, lunch and dinner = 15 total liters / family Showers = 10lt / person, one daily shower Kitchen wash = 13lts / day Total distance of the pipeline to the storage tank = 1200 meters Total height H from the pump point to delivery to the tank = 70 meters Determine: Estimation of the total volume of the recommended tank, an autonomy of at leas 2 days of storage. It is required to propose a pump that allows at least filling the tank between 5 to 12 hours operation, it must include details of the pump, as well as its curve Image: schematic detail of the proposed system
A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.81 cm and the other end is 0.28 cm. The larger and smaller ends are located 10 m and 4 m, respectively, from the datum line. If the flow at the 10 m datum line is 1.60 m/s and the pressure is 5244 kN/m2, compute for the pressure, in kPa, at the smaller end. Express your answer in 3 decimal places.