Table below presents the capillarypressure curve of anundersaturated oil reservoir. The oilwater contact is located at a depthof 4352 ft. the oil density atreservoir conditions is po= 39.5Ibm/ft3, and the water density ispw=64 Ibm/ft3. Using the capillarypressure information in the table.Plot depth versus water saturationWater saturationCapillary pressure (psi)0.169.000.24.200.32.000.41.150.50.800.60.620.70.550.80.480.90.4610.45

Write the formula for the height of oil above the free water level i.e. the height above the…

Table below presents the capillary pressure curve of an undersaturated oil reservoir. The oil water contact is located at a depth of 4352 ft. the oil density at reservoir conditions is po= 39.5 Ibm/ft3, and the water density is pw=64 lbm/ft3. Using the capillary pressure information in the table. Plot depth versus water saturation Water saturation Capillary pressure (psi) 0.16 9.00 0.2 4.20 0.3 2.00 0.4 1.15 0.5 0.80 0.6 0.62 0.7 0.55 0.8 0.48 0.9 0.46 1 0.45

Table below presents the capillary pressure curve of an undersaturated oil reservoir. The oil water contact is located at a depth of 4352 ft. the oil density at reservoir conditions is po= 39.5 Ibm/ft3, and the water density is pw=64 lbm/ft3. Using the capillary pressure information in the table. Plot depth versus water saturation Water saturation Capillary pressure (psi) 0.16 9.00 0.2 4.20 0.3 2.00 0.4 1.15 0.5 0.80 0.6 0.62 0.7 0.55 0.8 0.48 0.9 0.46 1 0.45

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

pllllzzzz help me right nowww plzzz The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
A closed tank contains 1.5 m of SAE 30 oil, 1m of water, 20 cm of mercury, and an air pocket in its upper part, all of them at 20 ° C. The absolute pressure at the bottom of the tank is 60 kPa. What is the pressure in the air bag?
A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. a. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? b. After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? c. What will be the absolute pressure (P3) in the smaller pipe? d. What is the volume flow rate through the smaller pipe?
To what height will 68˚F ethyl alcohol rise in a 0.005 in internal diameter glass capillary tube? The density of the alcohol is 49 lbm/ft3 note ? = 0.00156 ???/ ?? and ? = 0°.
Two small vessels are connected to a U-tube manometercontaining mercury(relative density 13.56) and the connectingtubes are filled with alcohol (relative density 0.82). Thevessel at the higher pressure is 2 m lower in elevation than theother. What is the pressure difference between the vessels whenthe steady difference in level of themercury menisci is 225 mm?What is the difference of piezometric head? If an inverted U-tubemanometer containing a liquid of relative density 0.74 wereused instead, whatwould be the manometer reading for thesame pressure difference?
What is the pressure at the bottom of 0.5m height fluid if the container moves 5m/s2 upward? Fluid has a density of 2000kg/m3 a. 13665Pab. 13258Pac. 14810Pad. 16145Pa
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
Three types of fluids stack in an open tank as shown in the picture. If the specific gravidties are sg1=1, sg2=1, sg3=1, and h1=0 m, h2=0 m, h3=0 m, calculate the gage pressure at location 4, P4(gage)=_________(kPa)
(Just Question a.) A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? What will be the absolute pressure (P3) in the smaller pipe? a. What is the volume flow rate through the smaller pipe?
Derive a formula for capillary rise (h) between two concentric glass tubes of radiuses RI and R2. determine its value for water if (G. = 0.072 N/m, RI=30mm, & R2=36mm) (Take smooth and very clean glass tubes).
Determine the submerged depth of a cube of steel 0.3 m on each side floating in mercury. The specific gravities of steel and mercury are 7.8 and 13.6 respectively.Answer: 0.172m Fluid mechanics (please include units)
A cylindrical disk ofwood weighing 45.0 N and having adiameter of 30.0 cm floats on a cylinderof oil of density 0.850 g /cm3(Fig.). The cylinder of oilis 75.0 cm deep and has a diameterthe same as that of the wood.(a) What is the gauge pressure at thetop of the oil column? (b) Supposenow that someone puts a weightof 83.0 N on top of the wood, butno oil seeps around the edge of thewood. What is the change in pressureat (i) the bottom of the oil and(ii) halfway down in the oil?