Answered: Tank A distributes water with a…

Tank A distributes water with a kinematic viscosity of 1.13 x 10° m²/s to gauge B as shown in Figure below at a rate of 0.1 m/s. If the pipe is 150 mm wrought iron, compute the energy loss.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Calculate the Reynolds number of the flow of water flowing with the velocity of 1 m/s and the…

Q: 2.fluid with a density of 1.23 kg/m^3 and a viscosity of 1.79 * 10 ^-5 N s/m^2 flows through 4mm…

Q: Give the classification of flow meters

A: Flow meters can be classified into two categories - Mass flow meters Volume flow meters

Q: A horizontal venturi meter having a throat diameter of 25 mm is set in a 60-mm-ID pipeline. Water at…

Q: A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25 mm in…

A: Given, Q=2 L/min=2×10-360 m3/s=3.333×10-5 m3/s d1=50 mmd2=25 mm hl=kv22-v122g z1-z2=1.5 m

Q: 1- Derive an expression for the flow rate q over the spillway shown in figure bellow per foot of…

Q: anometer being used to indicate the pressure difference between two points in a fabricated system.…

Q: If a fluid flow has a Reynolds number of 5654, then the flow is said to be laminar.

A: GIVEN DATA REYNOLD NUMBER GIVEN FOR FLOW WE HAVE TO FIND TYPE OF FLOW

Q: Water flows through a pipe having an inner radius of 10 mm at the rate of 36 kg/h at 25°C. The…

Q: 25 mm inside diameter,

A: Given that, a=45 mm,b=103 mm,c=48 mminside radius, r=25 mmthickness of cricular hole, t=25 mm,

Q: A liquid of viscosity 5.2x10-5 Ibf-sec/ft² is flowing in a rectangular duct. The equation of the…

A: Stress is defined as the intensity of force acting over a unit area. Shear stress is the intensity…

Q: Water flows through a horizontal pipe with a narrow constriction in the middle, as shown in the…

A: Given : To find : Velocity , Area

Q: Shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant…

A: Given data diameter of shaft (d) = 250 mm diameter of sleeve (D) = 251 mm Power required = 2204 W N…

Q: Shaft (250 mm diameter) rotates at 250 pm inside a sleeve (251 mm diameter) with a constant…

Q: Water at 25°C is flowing in a 26 cm commercial steel pipe. The total length of the pipe is 1416m. If…

Q: Sulfuric acid with a specific gravity of 1.98 and viscosity of 26.7 cP is flowing in a 35 mm…

Q: Calculate the Reynolds number of the flow of water flowing with the velocity of 1.5 m/s and the…

Q: Water at 10°C has a kinematic viscosity of 1.30 X 10-6 m2/s flows at the rate of 895.55 L/min from…

A: ν=1.30×10-6 m2secQ=895.55 Lmin orQ=.89555 m3sec

Q: Oil flows in a pipe 100 mm bore diameter with a Reynolds Number of 500. The density is 800 kg/m3.…

Q: Shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant…

Q: A pipe network consists of pipeline as shown. If the total rate of flow is 10 liters/sec, compute…

Q: Calculate the volume flow rate of water in the system if the manometer deflection h is 300 mm. (This…

Q: A water flows between parallel plates of infinite length. The bottom plate is fixed and the distance…

A: Couette flow In fluid dynamics, Couette flow is the flow of a viscous fluid in the space between two…

Q: A pitot-static tube is used to measure the speed of air at standard conditions at a point in a…

A: INTRODUCTION: The pitot tube is used to measure the speed of air, liquids, and practical equipment…

Q: A Venturimeter has 400mm diameter at the main and 150mm at the throat. If the difference of pressure…

A: Given data Main diameter of venturimeter (D) = 400 mm throat diameter (d) = 150 mm difference in…

Q: A commercial venturi meter is placed in a vertical pipe as shown below. Pressure gauges are located…

A: To find : Calculate downward discharge of of water and also calculate velocity at the section 2…

Q: . A crude oil of viscosity 0.9 poise and sp. gr. 0.8 is flowing through a horizontal circular pipe…

A: Given: μ=0.9 poise=0.09 Ns/m2SG=0.8d=80 mm = 0.08 mL=15 mm=50 kgt=15 sec

Q: An 80 mm schedule 40 steel pipe is 1800 m long and carries a lubricating oil between 2 points A and…

A: As per guidelines we need to answer only first question

Q: An oil with specific gravity of 0.9 and kinematic viscosity of 0.0002 m²/s flows upward through an…

A: Specific gravity of oil, SG=0.9Kinematic viscosity of oil, ν=0.0002 m2/sLength of pipe, L=10 mPipe…

Q: The venturi meter shown in Fig. 3.6 carries water at 60°C. The 200-mm specific gravity of the gage…

Q: Calculate the Reynolds number of the flow of water flowing with the velocity of 1 m/s and the…

Q: A vertical pipe of 40mm diameter carrying a flow of a Crude oil of u = 1.7 poise and relative…

Q: Freshwater at a temperature of 10°C flows at a rate of 0.10 m3/sec through the piping system…

A: Determine the value of the absolute roughness of the galvanized iron pipe.

Q: In a syringe of the figure shown, the drug had density of 900 kg/km' and absolute viscosity of 0.002…

Q: A crude oil of viscosity 0.9 poise and relative density 0.9 is flowing through a horizontal pipe of…

A: Given:-D=120mmL=12mM=785 Nt=25 secμ=0.9 poiseρ=0.9To find:-Pressure difference, ∆P

Q: Q. 1 Two pitot tubes are installed in the pipe of 300 mm diameter carrying water, one on the…

Q: Question 8 Water pipe has changes it diameter from 140 mm to 250 mm. If a flow of water from smaller…

A: When the flow is from the smaller to the larger pipe the loss due to the sudden enlargement u is…

Q: A horizontal venturimeter 160 mm x 80 mm is used to measure the flow of an oil of specific gravity…

A: Given that, Diameter of pipe d1=160 mm=0.16 m Diameter of throat, d2=80 mm=0.08 m Specific gravity…

Q: If the hydraulic radius of a similar shell is 1.28 mm, the density of the fluid flowing in it is 974…

A: Hydraulic radius of the shell, R=1.28 mm=0.00128 mFluid density, ρ=974 kg/m3Fluid velocity, V=37.1…

Q: In the scheme presented in Figure shows that H is 12m. the losses located (smaller) are referring to…

Q: Problem Water of constant density p flows down an inclined straight pipe, which has a circular cross…

A: a) The inlet volume should be equal to the outlet volume. So, for an ideal fluid the volume fluid…

Q: Medium lubricating oil (sg=0.85) is pumped through 360m of horizontal 75mm pipe at the rate of…

A: GivenSg=0.85L=360md=75mmQ=3.14 L/s=3.14×10-3 m3/s∆P=-300kPa

Q: The velocity of the fluid flowing thru a 50 mm diameter pipe is 1.35 m/s. The fluid has a kinematic…

Q: Figure Q1 shows the sewage siphon which regulates the level of water in the large holding tank A.…

Q: Shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant…

A: Given: Length of sleeve: L=150 mm Angular velocity of shaft: ω=250 RPM Diameter of shaft: d=250 mm…

Q: 5. An oil with a kinematic viscosity of 0.004 ft2/sec weighs 62 lb/ft³. It flows in a pipe with the…

A: Discharge or flow rate is the equal to the flow of fluid per unit volume. It's unit is m3/s The…

Concept explainers

Center of Gravity and Centroid

The term center of gravity indicates the position or location of a point about which the whole weight of a body or system is supposed to be concentrated, which means the whole weight of the body or system works through this point. It is closely related to mass distribution. For all positions of the body, the center of gravity would be a single point.

Question

subject (fluid mchanic 2)

Tank A distributes water with a kinematic viscosity of 1.13 x 106 m²/s to gauge B as
shown in Figure below at a rate of 0.1 m/s. If the pipe is 150 mm wrought iron, compute
the energy loss.
P2240kPa gauge
K- 0.9
295 m
B
150 m
25m
K-0.45
300 m
`K-0.9

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The head loss in 74 m of 150 mm diameter pipe is known to be 9 m when oil (s = 0.90) flows at 0.057 m^3/s. Assume viscosity of oil is 0.0389 Pa-s. Determine the Reynolds number. a. 19830 b. 15140 c. 11210 d. 13170
Determine the size of a galvanised iron pipe needed to transmit water a distance of 180 m at 0.085 m> /s with a loss of head of 9 m. (Take kinematic viscosity of water n=1.14 x 10°m? /s, and the average surface roughness for galvanised iron = 0.15 mm).
Complete the missing columns in the table and determine the experimental and theoretical values of the pipe friction factor using the respective formulae given above. Take the kinematic viscosity of water as 8.92x10-7 m2/s.
Air at 68 degrees Celsius is being pumped through a pipe of internal diameter 6.4 inches. If the volumetric flow rate has been set to 6.2 cubic feet per minute, determine if the flow is laminar or turbulent. Assume pressure is atmospheric. Use the data for air viscosity given below. c1 = 1.425x10^-6 c2 = 0.5039 c3 = 108.3
Question : SAE 30 oil at 20°C flows in the 3.5-cm-diameter pipe, which slopes at 37°. For the pressure measurements shown, determine Part (a) whether the flow is up or down and Part (b) the flow rate in m3/h. Neglect minor losses. Directions - Solve carefully, Write Clear, Label as Part (A) and (B) Circle Final answer(s) Hint : flows in the 3.5-cm-diameter pipe, *** USE IMAGE BELOW Pb = 190kPa, Pa = 550kPa, 25m, etc
A pipe-line carrying water has average height of irregularities projecting from the surface of the boundary of the pipe as 0.15 mm. What type of boundary is it? The shear stress developed is 4.9 N/m². The kinematic viscosity of water is .01 stokes.
Determine the pressure drop over a reducer with the following conditions: Fluid density: 25 kg/m3Fluid velocity: 1.5 m/sFluid viscosity: 0.001 Pa*sInlet diameter: 0.12 mOutlet diameter: 0.019 mPipe absolute roughness: 4e-4 m Give your final answer in Pa, rounded to the nearest whole number. [Ignore entrance/exit losses and velocity loss terms]
The flow rate of water in a garden hose is measured using the bucket-andstopwatch method. Filling a 5-L bucket takes 75 seconds. If the inner diameter of the hose is 10 mm and the density and viscosity of water are approximately 998 kg m-3 and 0.9 cP, respectively, (a) is the flow inside the hose laminar or turbulent? (b) If the flow rate is adjusted such that the flow is with Re = 2100, how long would it take to fill the same bucket?
what is the derivation of the reynolds number given as: R = Dv/v where: R - reynolds number D - internal diameter of a pipe v - kinematic viscosity v - velocity of the flow pls explain the derivation of this equation
The above pipe is exchanged for a parallel pipe with a cross sectional area of 0.3m2 and is 20 m long, with a surface roughness coefficient of 0.005. The dynamicviscosity of the water is 1.002 x 10-3 Ns/m. Find the Reynold’s number of the flowand use Haarland’s formula to find the friction coefficient and Darcy’s formula todetermine the frictional pressure loss. Then determine the pressure at the outlet ofthe pipe.
An oil with dynamic viscosity of 0.8 Pa.s and specific gravity of 0.9 is flowingthrough a horizontal pipe of 50 mm diameter. If the flow is a laminar flow, basedon Table 1 and the setting given, determine :(i) flowrate of the oil;(ii) centerline velocity;(iii) power required to maintain the flow;(iv) drag force on the pipe; and(v) velocity and shear stress at 10 mm from the wall. 2100 = Pressure Different(kN/m2) 99= PipeLength(m)
2) The horizontal pipe of diameter 240 mm is suddenly enlargement to a diameter of 480 mm. if the pipe carries water at 325 liters/sec, calculate the (i) Head loss to sudden enlargement,(ii) Pressure loss across the enlargement (p1-p2).