Task 5 Steam flows steadily through an adiabatic turbine. The inlet conditions of steam are 4 MPa 500°C, and 80 m/s, and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 12 kg/s. Steam table is available. P = 4 MPa T- 500°C V = 80 m/s Determine: (a) the change in kinetic energy per unit mass A ke (kJ/kg) Steam (b) the change in enthalpy per unit mass A h (kJ/kg) ni= 12 kg/s W ut (c) the work done per unit mass (kJ/kg) (d) the power outnut (MW)

Task 5 Steam flows steadily through an adiabatic turbine. The inlet conditions of steam are 4 MPa 500°C, and 80 m/s, and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 12 kg/s. Steam table is available. P = 4 MPa T- 500°C V = 80 m/s Determine: (a) the change in kinetic energy per unit mass A ke (kJ/kg) Steam (b) the change in enthalpy per unit mass A h (kJ/kg) ni= 12 kg/s W ut (c) the work done per unit mass (kJ/kg) (d) the power outnut (MW)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a trial run, the De Laval steam turbine at Oman Power Plant rotates at 3000 rpm. The steam is issued from the nozzle at 400 m/s and the nozzle angle is 20o. The blade speed ratio is 0.41and the friction loss in the blade channel is 15%of the kinetic energy corresponding to the relative velocity at the inlet to the blades. As a turbine engineer at that station, how do you determine the (i) power developed by the turbine for a flow rate of 10 kg/s and (ii) suitable inlet and outlet angles for the blades when axial thrust is zero. Also, how would you determine the size of the turbine wheel required? Draw a suitable velocity diagram.
At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage have inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (1) Specific entholpy drop across the stage in kJ/kg.
A blade pair in an axial flow compressor is being designed. The axial flow component of gas velocity is 174m/s. The engine diameter at the mean blade height is 0.73m and the blade height at the rotor inlet is 0.21m. The rotor's absolute inlet flow angle is 26 degrees. The stagnation conditions at the inlet to the blade pair are 298K and 130kN/m² Using Cp 1.005k/kg/K, R-0.287k/kg/K, and taking the ratio of specific heat capacities as 1.4, calculate the engine mass flow rate to the nearest kg/s
Air at a rate of 700 m^3/s enters a single stage compressor at 25 C and 100 kpa where it was compressed to 3000 kpa. If the operation is isothermal and reversible, calculate the power required in Kw if the pump efficiency is 60%
It is proposed to pump 10,000 kg/h of toluene at 114°C and 1.1 atm abs pressure from the reboiler of a distillation tower to a second distillation unit without cooling the toluene before it enters the pump. If the friction loss in the line between the reboiler and pump is 7 kN/m^2 and the density of toluene is 866 kg/m^3, how far above the pump must the liquid level in the reboiler be maintained to give a net positive suction head of 2.5m?
In a natural gas-pipeline compressor 110m3 /min propane is compressed polytropically. The inlet pressure is 101 kPa, and the temperature is 380C. The process follows pV1.08 = C. The exit pressure is 510 kPa. Determine (a) the exit temperature; (b) the heat loss; (c) the power required; (d) the mass flow rate.
The nozzle angle for an axial flow impulse turbine is 15°. The inlet absolutevelocity is 800 ft./s and the blade speed is 550 ft./s. Axial speed at the inlet andoutlet is assumed to be a constant. Calculate (a) energy transfer E, (b) change intotal (stagnation) and static enthalpies, (c) utilization factor.Ans: E=∆h0=245,038 ft-lbf/slug; ∆h=0; ε=0.77
Q . It is proposed to pump 8,000 kg/h of toluene at 114 oC and 1.1 atm abs pressure from the reboilerof a distillation tower to a second distillation unit without cooling the toluene before it enters thepump. If the friction loss in the line between the reboiler and pump is 7 kN/m2 and the density oftoluene is 866 kg/m3 . How far above the pump must the liquid level in the reboiler be maintained togive a net positive suction head of 3.5 m? Calculate the power required to drive the pump if the pumpis to elevate the toluene 10 m. The pressure in the second unit is atmospheric and the friction loss inthe discharge line is 35 kN/m2 . The velocity in the pump discharge line is 4 m/s.
Steam flows through a turbine at the rate of 100 lb/min with ∆KE = 0 and Q = 0. At entry, its pressure is 175 psia, its volume is 3.16 ft3/lb, and its internal energy is 1166.7 Btu/lb. At exit, its pressure is 0.813 psia, its volume is 328 ft3/lb, and its internal energy is 854.6 Btu/lb. What horsepower is developed? (b) The same as (a) except that the heat loss from the turbine is 10 Btu/lb of steam.
A reaction turbine has mean blade speed of 220 m/s and blade speed to steam velocity ratio of 0.7. Determine the angle at inlet of blade and work done per kg of steam flow if angle at exit is 20°.
The refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature.
The refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature. show and expalin each step please