Technician A says electronic transmission controls can malfunction if not provided with a good voltage source and ground. Technician B says the voltage drop of the negative battery cable should be 0.5 VDC or less. Which technician is correct? O Technician A O Technician B Both technicians A and B O Neither technician A nor B

Technician A says electronic transmission controls can malfunction if not provided with a good voltage source and ground. Technician B says the voltage drop of the negative battery cable should be 0.5 VDC or less. Which technician is correct? O Technician A O Technician B Both technicians A and B O Neither technician A nor B

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter22: Special-purpose Outlets For The Bathroom Ceiling Heat/vent/lights, The Attic Fan, And The Hydromassage Tub

Section22.1: Bathroom Ceiling Heater Circuits

Problem 12R

See similar textbooks

Similar questions

Problem Electrical will give thumbs up need answer from another expert
QUESTION 85 Type UF cable and associated fittings shall be _____. a. labeled b. identified c. approved d. listed
Which of the following boxes commonly used in electrical work is used at a point in the circuit where current is applied to utilization equipment? A. Device box B. Junction box C. Outlet box D. Pull box
Receptacles that provide power for a spa or hot tub shall be ________. Select one: a. AFCI-protected b. twist-lock c. ground-fault circuit-interrupter protected d. both B and C
A means shall be provided in each metal box over 100 cubic inches for the connection of an equipment grounding conductor. The means shall be permitted to be ______. a tapped hole the cover screw III. a screw used to mount the box (a.) I only (c.) I & II only (b.) II only (d.) I, II or III
17. Four electricians are discussing the size of boxes that must be installed to allow for the required amountof fill. Electrician A says that to calculate the proper size needed, the sidewall pressure should be countedas an installation parameter. Electrician B says that to calculate the proper size needed, each cable clampshould be counted as one conductor. Electrician C says that all wire nuts and fittings should be counted asone conductor. Electrician A says that to calculate the proper size needed, the mechanical stresses duringinstallation are the same as those encountered while in service. Which of the following statements iscorrect?A. Electrician D is correct.B. Electrician B is correct.C. Electrician C is correct.D. Electrician A is correct.
oleg is using a multimeter to test the circuit branch he's just installed. after turning off the current to the circuit at the service panel, he'll first attach one probe to the ----- in the end of the run. a. black wire b. box c. white wire d. ground wire Please answer with explanation In typing format
The connection method from the equipment grounding conductor to the box is carefully controlled. Three methods are provided: (1) a(n) , (2) equipment listed for grounding, and (3) a listed grounding device (e.g., ground clip). _____________
Control System Answer Step by Step Dont Copy from Bartleby
Four electricians are discussing wiring under raised floors in information technology equipment rooms. Electrician A says that wiring under the raised floor requires fire-resistant walls, floors, and ceilings between other occupancies. Electrician B says that wiring under the raised floor requires fire resistant halfway up the walls and floors between other occupancies. Electrician C says that the room must employ a disconnecting means that removes half of the power to all equipment in the room. Electrician D says that a disconnecting means isn't necessary for the room. Which of the following statements is correct? A. Electrician B is correct. B. Electrician D is correct. C. Electrician A is correct. D. Electrician C is correct.
When a set of electrical drawings is needed to get a permit, the drawings must include A. switch locations.B. brand names for each part.C. estimated cost of the project. D. fuse locations.
18. What should be done with light sources that are connected at each end of a cable while it's being repaired?A. They should be turned off and disconnected.B. They should be turned off only.C. Nothing, they can be left alone.D. They should be disconnected only.