Temperature, Pressure and Volume of air (Y=1.4) at the end of isentropic compression in an air standard Carnot heat engine cycle are 315.6 °C, 120 kPa and 0.05 m³ respectively. The volumetric ratio of the isothermal expansion ( = 3 ) and that of isothermal compression ( V₁ V₂ V₁ V₂ ¹3 = 3). The volumetric ratio the isentropic expansion (¹=6 ) and that of isothermal V4 V₂ V₁ compression (¹= 6). (Please draw a P-V diagram of the Carnot cycle) V₁ Calculate; a) The pressure, minimum Temperature and volumes of other states of the Carnot cycle. [ b) The heat supplied and rejected by the cycle c) The efficiency of the cycle

Temperature, Pressure and Volume of air (Y=1.4) at the end of isentropic compression in an air standard Carnot heat engine cycle are 315.6 °C, 120 kPa and 0.05 m³ respectively. The volumetric ratio of the isothermal expansion ( = 3 ) and that of isothermal compression ( V₁ V₂ V₁ V₂ ¹3 = 3). The volumetric ratio the isentropic expansion (¹=6 ) and that of isothermal V4 V₂ V₁ compression (¹= 6). (Please draw a P-V diagram of the Carnot cycle) V₁ Calculate; a) The pressure, minimum Temperature and volumes of other states of the Carnot cycle. [ b) The heat supplied and rejected by the cycle c) The efficiency of the cycle

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Diesel cycle has a compression ratio of 22 and begins its compression at 83 kPa and 15°C. The maximum cycle temperature is 1200°C. Utilize air-standard assumptions. The properties of air at room temperature are R = 0.287 kPa·m3/kg·K, cp = 1.005 kJ/kg·K, cv = 0.718 kJ/kg·K, and k = 1.4. Determine the thermal efficiency of this cycle using constant specific heats at room temperature. The thermal efficiency of this cycle (in decimal fraction)
A turboshaft engine comprising a gas generator and a free power turbine is selected to provide propulsive power for a helicopter. The helicopter is hovering in ISA conditions at an altitude of 4100 feet. The following data applies to this engine at this static max power operating point. Intake mass flow: 8.9 kg/s Compressor pressure ratio: 24.5 Compressor isentropic efficiency: 88% Mechanical efficiency: (HP & PT shaft) 99% Combustion chamber pressure loss Combustion chamber inlet pressure 4% Combustion efficiency 98.8% Combustion chamber exit temperature: 1585K Gas generator turbine isentropic efficiency: 92% Power turbine isentropic efficiency: 90% The effects of the intake and exhaust ducts may be ignored. It may be assumed that for: Air: Cp = 1.005 kJ/kg • K, y = 1.4, R = 0.287 kJ/kg • K Combustion gases: Cp = 1.148kJ/kg • K, y = 1.333, R = 0.287 kJ/kg • K A 6% direct bleed of air from the exit of the compressor is…
A turboshaft engine comprising a gas generator and a free power turbine is selected to provide propulsive power for a helicopter. The helicopter is hovering in ISA conditions at an altitude of 4100 feet. The following data applies to this engine at this static max power operating point. Intake mass flow: 8.9 kg/s Compressor pressure ratio: 24.5 Compressor isentropic efficiency: 88% Mechanical efficiency: (HP & PT shaft) 99% Combustion chamber pressure loss Combustion chamber inlet pressure 4% Combustion efficiency 98.8% Combustion chamber exit temperature: 1585K Gas generator turbine isentropic efficiency: 92% Power turbine isentropic efficiency: 90% The effects of the intake and exhaust ducts may be ignored. It may be assumed that for: Air: Cp = 1.005 kJ/kg • K, y = 1.4, R = 0.287 kJ/kg • K Combustion gases: Cp = 1.148kJ/kg • K, y = 1.333, R = 0.287 kJ/kg • K A 6% direct bleed of air from the exit of the compressor is…
10 m3/min of free air is to be compressed to 8 bar gauge in two stages. Assuming a 2 bar gauge intercooler pressure and a polytropic index of 1.3, what is the power consumption of the second stage compressor ? Please choose correct option a. 27.76 KW b. 22/7/π m3/min c. 20.46 KW d. 20.46 bar-m3/min e. 48 HP
The compression ratio of a compression-ignition engine is 13.5 to 1. The diameter of the cylinder is 505mm and the stroke to bore ratio is 1.21 to 1. At the beginning of the compression, the pressure and the temperature of the air in the cylinder is 105 Kpa and 51C, and compression follows the law PVn =C where n=1.33. Determine the following:1.1) The temperature at the end of compression 1.2) Volume at the beginning of compression 1.3) The mass of air inside the cylinder 1.4) Evaluate whether the work is done on or done by the air?
A regenerator of 75 percent effectiveness is used in an air-standard Brayton cycle working between pressures of 15 psia and 75 psia. Determine the work per pound of air and the efficiency of the cycle if the maximum and minimum temperatures of the cycles are 1700 R and 550 R, respectively.
A diesel engine operating on an air standard condition has a net work output of 300kJ/kg if the heat added amounts to 530kJ/kg, determine the theoretical exhaust temperature of the engine if the initial temperature is 20degree C
In an ideal diesel cycle the pressure and temperature at the beginning of the adiabatic compression are 98.5kN/m squared and 60 degrees c respectively.The maximum pressure attained during the cycle is 4.5MN/m squared and the heat received during the cycle is 580kJ/kg gas.Determine ,for the cycle, (a) the volume ratio of compression (b) the temperature at the end of compression (c) the temperature at the end of heat reception (d)the temperature at the end od adiabatic expansion
What are the effects of varying the compression ratio on the thermal efficiency and power output of an internal combustion engine?
10 m3 /min of free air is to be compressed to 8 bar gauge in two stages. Assuming an intercooler pressure of 2 bar gauge and polytropic index of 1.3, what is the power consumption of the first stage compressor ? pls choose one a.20.44 KW b.48.8 HP c.22.4 litre/mole d.42.2 bar-m3/min e.25.12 KW
The initial pressure and temperature of air in an Otto cycle engine during compression are 90 kPa and 12°C. Determine the maximum pressure occurring in the cycle if the initial and final temperature during heat addition process are 350°C and 1250°C, and the compression ratio is 6. Please complete the answer for good feedback.?
the ratio of compression in a diesel engine is 16 to 1 and the temperature of the air at the beginning of the compression is 49 C. calculate the temperature at the end of compression assuming it follows the law PV^1.34=c