The 1.5-m-long gate is a quarter circle with radius = 0.90 m and is hinged at A. Determine the following: (a) Av (m²),(b) hy (m), (c) Fx (kN), (d) hpv (m), (e) Fv (kN). (F) Determine the horizontal force P, required to hold the gate in place.Neglect friction at the hinge and the weight of the gate.WaterA

Name: The 1.5-m-long gate is a quarter circle with radius = 0.90 m and is h
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The 1.5-m-long gate is a quarter circle with radius = 0.90 m and is hinged at A. Determine the following: (a) Av (m²),(b) hy (m), (c) Fx (kN), (d) hpv (m), (e) Fv (kN). (F) Determine the horizontal force P, required to hold the gate in place.Neglect

Since we only answer upto three subparts we will answer the first three. Please resubmit the…

Engineering

Mechanical Engineering

The 1.5-m-long gate is a quarter circle with radius = 0.90 m and is hinged at A. Determine the following: (a) Av (m²), (b) hy (m), (c) Fx (kN), (d) hev (m), (e) Fv (kN). (F) Determine the horizontal force P, required to hold the gate in place. Neglect friction at the hinge and the weight of the gate. Water A

The 1.5-m-long gate is a quarter circle with radius = 0.90 m and is hinged at A. Determine the following: (a) Av (m²), (b) hy (m), (c) Fx (kN), (d) hev (m), (e) Fv (kN). (F) Determine the horizontal force P, required to hold the gate in place. Neglect friction at the hinge and the weight of the gate. Water A

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
Determine the force F required to pull up the 3.54m stopper from the drain of a sink if the depth of water is 10 in. Use =0.036lb/in.3 for water and neglect the weight of the chain.
Each of the three gates has a constant width 1: (perpendicular to the paper). Calculate the force P required to maintain each gate in the position shown. Express your answers in terms of b, c, h, and (the weight density of the fluid).
The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
The high-pressure water cock is rigidly attached to the support at D. Neglecting the weights of the members, draw the FBD of the entire assembly and count the unknowns.
Determine the smallest distance I) that would prevent the concrete dam from tipping about corner A. Use w=62.4lb/ft3 for water and c=150lb/ft3 for concrete.
The 3 × 4-m side of an open tank is hinged at its bottom A and is held in place by a thin rod BC. The tank is to be filled with glycerine with a density of 1263 kg/m3 . Determine the force T in the rod and the reaction at the hinge after the tank is filled to a depth of 2.9 m.
Cords are looped around a small spacer separating two cylinder each weighing 400kn and pass over a frictionless pulleys to weights of 200KN and 400kn. Determine the angle and the pressure N between the cylinder and smooth horizontal surface
The strength per meter of the longitudinal joint in the figure is 480 kN, whereas or the girth joint is 200 kN. Determine the maximum diameter of the cylindrical tank if the internal pressure is 1.5 MPa.
A crane is used to lower weights into a lake for an underwater construction project. Determine the tension in the rope of the crane due to a 3-ft-diameter spherical steel block (density = 494 lbm/ft3) when it is (a) suspended in the air and (b) completely immersed in water.
The rectangular panel, which is 4 m wide, 3 m high block the end of a 3 m deep water channel. The is suspended around a horizontal axis along its upper edge through point B and is prevented from opening by a fixed edge at point C. Determine the force which is exterted on the panel by the ridge as shown in fig.(2).