Answered: The 10 kg block is supported by two…

The 10 kg block is supported by two springs having the stiffness shown. Determine the stretch of spring AB, S(AB): 0.4 m L0.3 m B. 0.4 m kAc - 1.5 kN/m 1.2 KN/m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An 18 coils helical spring having a load of 100kg. The modulus of elasticity in shear of spring is 96.62 GPa, OD of 9.256 cm and with wire diameter of 9.525 mm. The spring is squared and ground ends. Compute for the following respectively: 1) number of effective coils2) spring index3) axial load (N) 4) deflection (mm) Answers must be at least in 4 decimal places.
Compute the minimum vine diameter to provide a desired factor of safety of 1.7 against yield-type failure. Assume a yield stress of 300 MPa, and that the mass of the monkey is 65 kg. Hint Weight (N) = Mass (Kg) X g (9.81 m/s2)
An 18 coils helical spring having a load of 100kg. The modulus of elasticity in shear of spring is 96.62 GPa, OD of 9.256 cm and with wire diameter of 9.525 mm. The spring is squared and ground ends. Compute for the deflection (mm) Answers MUST be at least in 4 decimal places.
1. A closed coiled helical spring, is made out of a 10mm diameter steel rod, has 10 complete coils each of mean diameter of 80mm. Calculate for force of 200N: (a) the stress induced in the section of the rod (b) the deflection under the pull (c) the amount of energy stored in the spring during extension. Take G=84GPa. 2. A composite spring has two closed coiled springs connected in series, each spring has 12 coils at a mean diameter of 25mm. Find the wire diameter for one if the other is of 2.5mm diameter and the stiffness of the composite spring is 700N/m.Estimate the greatest load that can be carried by the composite spring, and the corresponding extension, for a maximum shear stress of 180MPa. Take G=80GPa.
An 18 coils helical spring having a load of 100kg. The modulus of elasticity in shear of spring is 96.62 GPa, OD of 9.256 cm and with wire diameter of 9.525 mm. The spring is squared and ground ends. Compute for the following respectively : 1) number of effective coils 2) spring index 3) axial load 4) deflection (mm)
A helical spring composed of 20 turns of 20mm diameter wire on a mean radius of 80mm when the spring is supporting a load of 2kN. (G=83,000 GPa) Compute for the following respectively : 1) stress factor 2) shear stress (MPa)
A spring balance is calibrated in an environment at a temperature of 25oC and has the following deflection/load characteristics Load (Kg) 0 2 Deflection(mm) 0 36 It is used in an environment at a temperature of 35oC and the following deflection/ load characteristics. Load (Kg) 0 2 Deflection(mm) 4 50 Determine ZERO DRIFT at 25oC ? ZERO DRIFT at 35oC ? ZERO DRIFT? ZERO DRIFT/oC?
A safety valve, 11 mm in diameter, is to blow off at a pressure of 1.5 MPa. It is held on itsseat by means of a helical compression spring, with initial compression of 16 mm. Themaximum lift of the valve is 27 mm. The ratio of mean coil diameter to wire diameter is5. The spring is made of cold drawn steel wire with ultimate tensile strength of 1400 MPa. (G = 81 370 N/mm2), Calculate:i. Wire diameter;ii. Mean coil diameteriii. Number of active coilsiv. Free lengthv. Pitchvi. Actual spring constantvii. Required Stiffness
The helical compression spring is made of 12mm wire diameter with 132 mm mean diameter. Determine stiffness of the spring when modulus of rigidity G=80 kN/mm2,number of turn is 13 and axial load is 190N.
A spring with ends squared and ground, wire diameter d = 4 mm, outside diameter Do = 40 mm, 18 total coils, and free length Lf = 140 mm has been chosen for an application where the initial deflection is 15 mm and the working deflection is 50 mm. The shear modulus is G= 80 GPa. Part A Determine the clash allowance. Express your answer as a percentage using three significant figures. Part B Determine the spring rate.
A spring (squared and ground) having a pitch 0.75 inch has a mean diameter of 1.5in and a wire diameter of 0.25in. After applying a certain load, the spring deflects 0.5in with a corresponding stress of 30.75 ksi. The spring is to be made of tempered steel wire having a shear modulus of 12 million psi.
A semi-elliptic spring used for automobile suspension, consists of two extra full-length leaves and eight graduated-length leaves, including the master leaf. The centre-to centre distance between the two eyes is 1 m. The leaves are made of steel 55Si2Mo90 (Syt = 1500 N/mm2and E = 207000 N/mm2) and the factor of safety is 2. The maximum spring load is 30 kN. The leaves are pre- stressed so as to equalize stresses in all leaves under maximum load. Determine the dimensions of the cross-section of the leaves and the deflection at the end of the spring.