The 25-mm-diameter 2014-T6 aluminum rod is subjected to the uniform distributed axial load. Take E = 73.1 GPa. (Figure 1) Part A Determine the displacement of end A. Express your answer to three significant figures and include the appropriate units. ? 8A = 0.27 mm Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining Figure < 1 of 1 Provide Feedback -30 kN/m 900 mm

The 25-mm-diameter 2014-T6 aluminum rod is subjected to the uniform distributed axial load. Take E = 73.1 GPa. (Figure 1) Part A Determine the displacement of end A. Express your answer to three significant figures and include the appropriate units. ? 8A = 0.27 mm Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining Figure < 1 of 1 Provide Feedback -30 kN/m 900 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.4.2P: A cantilever aluminum column has a square tube cross section with an outer dimension of 150 mm. The...

See similar textbooks

Similar questions

An arrow is shown, where the most critical part (r) of said arrow is observed.to. It is designed with approximate relative sizes of d = 0.65D and r = D/15 with the diameter d conforming to the size of the inner diameters of standard metric bearings.b. It is made of SAE 2340 steel, heat treated to obtain minimum strengths in the shoulder area of Sut = 1226 MPa and Sy = 1130 MPa.c. At the shoulder, the arrow is subjected to a completely reversible bending moment of M = 80N and a uniform torque of T = 55Nmd. It has a safety factor n = 2 Determine the dimensions of the shaft for infinite life.
Two vertical steel wires each 1.5mm diameter and 1.2m long support a light rod over a span of 0.3m. A concentrated load of 250N is then applied vertically downwards at a point 0.1m from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E=200 GPa (Complete Solution)
Determine the diameter of a circular rod made of ductile material with a fatigue strength (complete stress reversal) σe = 280 MPa and a tensile yield strength of 350 MPa. The member is subjected to a varying axial load from 700 kN to – 300 kN. Assume Kt = 1.8 and F.S. = 2.
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (Sf) is equal to 0.8 Su and endurance Strength (Se) is equal to 0,5 Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S-N diagram
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength ( Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (S) is equal to 0.8Su and endurance Strength (Se) is equal to 0, 5Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S - N diagram
The tube is made of copper and has an outer diameter of 35 mm and a wall thickness of 7 mm. Determine the eccentric load P that it can support without failure.The tube is pin supported at its ends. Ecu = 120 GPa, sY = 750 MPa.
The steel bar has the original dimensions shown in the figure. It is subjected to an axial load of 50 kN. Est=203 GPa, vst=0.27. Determine the change in its length. Express your answer to three significant figures and include appropriate units.
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figures
The stepped bar with a circular hole is made of annealed 18-8 stainless steel. The bar is 12 mm thick and a change in depth from D = 130 mm to d = 100 mm. It will be subjected to an axial tensile load of P = 70 kN. The normal stress in the bar is not to exceed 150 MPa. Determine: a) the maximum allowable hole diameter b) the minimum allowable fillet radius
The rigid bar ABC is supported by pin at A and aluminum wire BD, is horizontal before the Load P is applied. Find the vertical displacement of point C caused by the load P=35KN. Where E of aluminum equals 70GPA and the area of the wire is 200mm^2 -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
A damper square mat is supporting a dead load weight of8 kN. Helical springs will be used to support the loadlocated at all corners with shearing stress of 120.6 Mpaat 20 turns. The spring has a deformation of 98.7 mmwith a mean radius of 80 mm. Design the minimumdiameter of the wire to support a load. Use G = 83 Gpa.
Two rods are connected to each other and are restrained at top and bottom. The top portion is steel with modulus of elasticity equal to 200x10^3 MPa and coefficient of thermal expansion equal to 11.7x10^-6/C, the bottom is made up of brass with modulus of elasticity equal to 105x10^3 MPa coefficient of thermal expansion equal to 20.9x10^-6/"C. The temperaturé rose to 50°C from normal condition introducing stresses in the bar. Determine the force induced in the bar. Note: Final Answer in 4 decimal places.