The 304 stainless steel post A has a diameter of d = [d] mm and is surrounded by a red brass C83400 tube B. Both rest on the rigid surface. If a force of F kN is applied to the rigid cap, determine the average normal stress developed in the post and the tube. Ga= 193 GPa, G= 101 GPa. %3D

The 304 stainless steel post A has a diameter of d = [d] mm and is surrounded by a red brass C83400 tube B. Both rest on the rigid surface. If a force of F kN is applied to the rigid cap, determine the average normal stress developed in the post and the tube. Ga= 193 GPa, G= 101 GPa. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: a) The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of 20…

A: Given data outer diameter of pipe (do) = 28 mm inner diameter of pipe (di) = 20 mm diameter of rod…

Q: Determine the stress components acting on the inclined plane AB. Solve the problem using the method…

Q: Air pressure in the cylinder is increased by exerting forces P = 2 kN on the two pistons, each…

A: Given Data: The outer radius of the cylinder is: rO=47 mm The force exerted on the walls is: P=2…

Q: The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed…

A: Standard values for given brass and aluminium rods

Q: The rectangular reinforced concrete column is reinforced with 6- 20 mm steel bars as shown. If b =…

A: Given Data B=250 mm D=400 mm d=20 mm(steel bar) P=400 kN

Q: Two A992 steel pipes, each having a cross-sectional area of 0.32 in2, are screwed together using a…

A: The modulus of elasticity of A992 steel is given by table, It is assumed that P force is acting in…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 kN applied at A. Assume a…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a…

Q: The thin-walled cylinder can be supported in one of two ways as shown. Determine the state of stress…

A: Given data as per the question Internal pressure = 65 psi Wall thickness = 0.25 in Diameter = 8 in…

Q: A cylinder having the dimensions shown is made from magnesium Am 1004-T61. If it is struck by a…

A: The given problem is solved using formulae for Strain Energy due to axial loading. All the units…

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN F2 = 6KN F3 =…

A: Given: F1 = 7KN F2 = 6KN F3 = 2KN F4 = 9KN

Q: The bellcrank is in equilibrium a) determine the diameter of the bar DE if the normal stress is…

A: GIVEN: Load W= 30KN length of road BC:LBC=0.2m length of road CD:LCD=0.3m thickness of plate C: t=…

Q: The frame supports the distributed load shown. Determine the state of stress acting at point D. Show…

A: In this problem, the state of stress at point D is determined by drawing the FBD as discussed in the…

Q: The center post B of the assembly has an original length of 123 mm, whereas posts A and C have a…

Q: Determine the stress components acting on the inclined plane AB. Solve the problem using the method…

A: Consider the diagram is shown below for the area components. Consider the free body diagram of the…

Q: HWs. 1. The grains of wood in the board make an angle of 20° with the horizontal as shown. Using…

A: As per given question Axial load=250N Angal=20° Width=25mm Thickness=60mm We have to draw mohr…

Q: The column is subjected to an axial force of 8 kN which is applied through the centroid of the…

Q: The rod has a diameter of 1 in. and a weight of 10 lb>ft. Determine the maximum torsional stress…

A: diameter of rod (d) = 1 in. weight of rod (w) = 10 lb-ft the FBD of the cut segment of the rod is…

Q: The sign is subjected to the uniform wind loading. Determine the stress components at points A, B, C…

Q: Determine the normal stress and shear stress acting on the inclined plane AB. Solve the problem…

A: Given data: Normal stress in y direction, σy = - 15 ksi Normal stress in x direction, σx = 0 Shear…

Q: The d = 15-mm-diameter solid rod passes through a D=20-mm-diameter hole in the support plate. When a…

Q: Determine the stress components acting on the plane AB. Solve the problem using the method of…

Q: Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load…

A: Answer: The stress in each of the two vertical rods are: (a) Steel : 185.9158 MPa (Tensile stress).…

Q: If a critical point at structural element is subjected to the stress shown on the 2D element,…

A: Maximum principal stress theory :- Failure occur when maximum principal stress on body exceeds the…

Q: A cylinder having the dimensions shown is made from magnesium Am 1004-T61. If it is struck by a…

A: Given Weight of the block=W=800lb Mass =M=W/g Where g=gravitational force=32.2ft/s2 M=800/22.2=36.03…

Q: The bolt has a diameter of 20 (mm) and passes through a tube that has an inner diameter of 50 (mm)…

Q: The thin-walled cylinder can be supported in one of two ways as shown. Determine the state of stress…

A: Calculated the state of stress in the wall of the cylinder for both cases.

Q: The grains of wood in the board make an angle of 20° with the horizontal as shown. Determine the…

A: Given, Load P = 250 N Load Perpendicular to AB' = Pn N Load Parallel to AB' = Ps N Length L = 300 mm…

Q: The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed…

A: Given T(1)=50 degree F T(2)=120 degree F Area cross-section =1.75 in(2)

Q: The bar has a diameter of 40 mm. Determine the state of stress at point A and show the results on a…

A: Section properties can be determined as

Q: The two circularrod segments, one of aluminum and the other of copper, are fixed to the rigid walls…

Q: The 304 stainless steel post A has a diameter of d = 50 mm and is surrounded by a red brass C83400…

Q: The rib-joint pliers are used to grip the smooth pipe C. If the force of 100 N is applied to the…

A: Given: The magnitude of the force applied on the handles is FH=100 N. The length and breadth of the…

Q: F8-16. A 20-mm-wide block is bonded to rigid plates at its top and bottom. When the force Pis…

A: Given data: Maximum elastic strain, γmax. = 0.005 rad. Calculate the angle due to shear from the…

Q: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is…

A: Given: The thickness of the wall is t=0.025 in. The inner diameter of the wall is d=0.5 in. The…

Q: | Determine the stress components acting on the inclined plane AB. Solve the problem using the…

A: We have to solve the equilibrium methods

Q: The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial…

Q: The rigid beam is supported by three 25-mm diameter A-36 steel rods. If the force of P = 230 kN is…

Q: The beveled gear is subjected to the loads shown. Determine the stress components acting on the…

A: The free body diagram of beveled gear is shown below:

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 12 kN applied at A. Assume a…

Q: If a critical point at structural element is subjected to the stress shown on the 2D element,…

Q: Determine the state of stress at point A on the cross section of the pipe assembly at section a-a.…

Q: If a critical point at structural element is subjected to the stress shown on the 2D element,…

A: Factor of safety = Sultσe

Q: The center post B of the assembly has an original length of 122 mm, whereas posts A and C have a…

Q: The drill is jammed in the wall and is subjected to the torque and force shown. Determine the state…

A: The free body diagram of the system is as follows.

Q: The stainless steel solid post 'A' has a diameter of, d = 2 in, and is surrounded by a red brass…

Q: The two cylindrical rod segments are fixed to the rigid walls such that there is a gap of 0.01 in.…

A: Write the given data with suitable variables. LCu=12 indCu=1.25 inLAl=6 indAl=1.25 inαAl=13×10-6…

Q: The uniform bar, having a cross-sectional area of A and mass per unit length of m, is pinned at its…

A: Consider Nx is the normal force acting at the cross-section at a distance x from the pinned centre.…

Q: Determine the maximum normal stress that loading produces in the 6061-T6 aluminum plate. 0.25 in.…

Q: The drill is jammed in the wall and is subjected to the torque and force shown. Determine the state…

A: A drilling machine is used to drill in-wall or furniture. To analyze the drill bit stresses we first…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

The 304 stainless steel post A has a diameter of d [d] mm
F KN
and is surrounded by a red brass C83400 tube B. Both rest
on the rigid surface. If a force of F kN is applied to the
rigid cap, determine the average nomal stress developed
LImm
To mm
in the post and the tube. G,= 193 GPa, G= 101 GPa.
mm
= 200 mm
F: 25N
t =12
d=50
ro=75

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the bolt is subjected to a compressive force of P = 20 kN, determine the average normal stress in the steel and the bronze. Est = 200 GPa, Ebr = 100 GPa.
The center post B of the assembly has an original length of 122 mm, whereas posts A and C have a length of 126 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress (in MPa) post A. The posts are made of aluminum and have a cross-sectional area of 403 mm2. Ealuminum = 70 GPa. The correct answer is 887.66682. Show solution pls.
The thin-walled cylinder can be supported in one of two ways as shown. Determine the state of stress in the wall of the cylinder for both cases if the piston P causes the internal pressure to be 65 psi. The wall has a thickness of 0.25 in. and the inner diameter of the cylinder is 8 in.
433 The steel pipe is filled with concrete and subjected 10 a compressive force of 80 kN. Determine the averaee normal stress in the concrete and the steel due to this loading. The pipe has an outer diameter of 80 mm and oo inner diameter of 70 mm. E, = 200 GPa, E. = 24 GPa.
The shaft assembly is made from a steel tube 1 in. in diameter,which is bonded to a solid brass core 0.5 in. in diameter. If atorque of 250 lb-ft is applied at its end, determine the maximumshear stress in psi experienced by the assembly. Take G for steelat 11.4x103 ksi and G brass at 5.2 x 103 ksi.
The bellcrank is in equilibrium a) determine the diameter of the bar DE if the normal stress is limited to 100MN/m2.b) Determine the diameter of the pin located at C if the shear stress is limited to 70 MN/m2.c) Determine the crushing force in the support plates in C with a thickness of 6mm.
A cylindrical tank has an inner radius of 750mm and length of 3.0m. Determine its minimum thickness (to nearest mm) if it is subjected to an internal pressure of 150kPa and tangential stress is not to exceed by 12MPa. Indicate the free body diagram
The steel bracket below is used to connect the ends of two cables. If the applied force P=1.50kip, determine the maximum normal stress (in ksi) in the bracket. Assume the bracket is made from a rod having a diameter 1.5in.
The bar has a diameter of 40 mm. Determine the state of stress at point A and show the results on a differential volume element located at this point.
The aluminum rod AD (E=73 GPa, 0=23x10°6/°C) has a diameter of 15 mm and isattached to the rigid support at A when the temperature T; = 30°C. If thetemperature becomes T: = -20°C, and the axial loads are applied to the rod asshown, determine: a) The location and magnitude of the maximum stress acting on the rod ADb) Displacement of point Dc) Average strain in part BC
The beveled gear is subjected to the loads shown.Determine the stress components acting on the shaftat point B, and draw the results on a stress elementat this point. The shaft has a diameter of 1 in. and isfixed to the wall at C. A = 0.7854 in2 J = 0.098175 in4 I = 0.049087 in4 (QB)z = 0 (QB)x = 0.0833 in3
The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. Determine the maximum normal stress in the block at any possible orientation.