The 38-lb collar A is released from rest in the position shown and slides up the 30° inclined bar with negligible friction due to the action of the constant force P = 45 lb applied. on the wire. Assuming that the maximum deformation of the spring is 6 inches, determine a) The work, in lb ft, done by the force P on the collar to bring it from the position shown to the position of maximum deformation of the spring.

The 38-lb collar A is released from rest in the position shown and slides up the 30° inclined bar with negligible friction due to the action of the constant force P = 45 lb applied. on the wire. Assuming that the maximum deformation of the spring is 6 inches, determine a) The work, in lb ft, done by the force P on the collar to bring it from the position shown to the position of maximum deformation of the spring.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

By using a forked rod, a smooth cylinder C having a mass of 0.5 kg is forced to move along the vertical slotted path (r = 0.4 θ) m, where θ is in radians. If the angular position of the arm is θ = (0.3 t3 ) rad, where t is in seconds. The cylinder is in contact with only one edge of the rod and slot at any instant. Find "the force of the rod on the cylinder at the instant t=2s" Find "the normal force of the slot at the instant t=2s" Find the "radius of curvature at t=2s" Find the "ψ angle at t=2s"
Knowing that the coefficient of static friction between the tires and the road is 0.80 for the car as shown in figure 2. At this car, suddenly brakes are applied when it was moving with velocity of 360 inch/sec and it skidded to rest in 240 inch. The mass of the car is 300 pounds. Determine the magnitude of the normal reaction and of the friction force at each wheel as the car skidded to rest.
A 7.5-lb collar is released from rest in the position shown, slides down the inclined rod, and compresses the spring. The direction of motion is reversed and the collar slides up the rod. Knowing that the maximum deflection of the spring is 5 in., determine (a) the coefficient of kinetic friction between the collar and the rod, (b) the maximum speed of the collar.
The W1= 69.01-lb block shown rests on a smooth plane (coefficient of kinetic friction = 0) with an angle of θ=34∘ from horizontal. It is connected by a flexible inextensible cord that passes around weightless, frictionless pulleys to a support. The W2 =134.93-lb weight is attached as shown. After the system is released from rest, in what distance will the block on the plain attain a speed of 10.0 ft/s?
The 38-lb collar A is released from rest in the position shown and slides up the 30° inclined bar with negligible friction due to the action of the constant force P = 45 lb applied. on the wire.Assuming that the maximum deformation of the spring is 6 inches, determine b) The required stiffness K of the spring, in lb/ft. The position of the small pulley B is fixed.
A 5-kg bag is gently pushed off the top of a wall and swings in a vertical plane at the end of a 2.4m rope which can withstand a maximum tension of 100 N. Determine (a) the elevation h betweenpoint A and point B where the rope will break, (b) the distance d from the vertical wall to thepoint where the bag will strike the floor.
A system of blocks is pulled by a force P. The string connecting blocks A and B passes over apulley whose coefficient of friction between string and pulley is 0.25. The coefficient of frictionbetween surface and blocks is 0.20. Block A weighs 200N and block B weighs 300N. Determine,a. the minimum value of P for impending motion to the right.b. the tension connecting block B.
A bowler projects an 8-in.-diameter ball weighing 12 lb along an alley with a forward velocity v0 of 15 ft/s and a backspin ω0 of 9 rad/s. Knowing that the coefficient of kinetic friction between the ball and the alley is 0.10, determine (a) the time t1 at which the ball will start rolling without sliding, (b) the speed of the ball at time t1, (c) the distance the ball will have traveled at time t1
Show the complete solution. Put notes on steps. In the system shown, a 150 N collar-pulley assembly slides on a horizontal shaft with coefficient of kinetic friction pk = 0.10 between the collar and the shaft, and is acted upon by a force P with a magnitude of P = 261.65 N at an angle e = 31.16° as shown. Knowing that the assembly is initially at rest, what is the velocity after 3s? Also, at this instant, find the tension in the cord and the velocity of block A.
A belt of negligible mass passes between cylinders A and B and is pulled to the right with a force P. Cylinders A and B weigh, respectively, 5 and 20 lb. The shaft of cylinder A is free to slide in a vertical slot and the coefficients of friction between the belt and each of the cylinders are µs = 0.50 and µk = 0.40. For P = 3.6 lb, determine (a) whether slipping occurs between the belt and either cylinder, (b) the angular acceleration of each cylinder.
Pin B weighs 0.1kg and is free to slide in a horizontal plane along therotating arm OC and along the circular slot DE of radius b=500mm.Neglecting friction and assuming that θ= 15 rad/s andθ=250 rad/s2 for the position θ= 20o , determine for that position(a) the radial and transverse components of the resultant forceexerted on pin B, (b) the forces P and Q exerted on pin B,respectively, by rod OC and the wall of slot DE.
A series of small packages, each with a mass of 0.5 kg, are discharged from a conveyor belt as shown. Knowing that the coefficient of static friction between each package and the conveyor belt is 0.4, determine (a) the force exerted by the belt on the package just after it has passed point A, (b) the angle 0 defining the point B where the packages first slip relative to the belt.