The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in Figure Q2 (b). The motor exerts a torque of 7 Nm to drive the system. The coefficient of static friction for both pulley is 0.35 and both pulleys has an equivalent diameter. Calculate the tension of T, and Ts of V-belt just before it start rotating.

The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in Figure Q2 (b). The motor exerts a torque of 7 Nm to drive the system. The coefficient of static friction for both pulley is 0.35 and both pulleys has an equivalent diameter. Calculate the tension of T, and Ts of V-belt just before it start rotating.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.50P: The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the...

See similar textbooks

Similar questions

The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
A pulley system uses four v-section belts each with a cross-sectional area of 700mm 2, an included angle of 40°, and density 1400kg/m 3 The angle of lap is 130° on the smaller wheel, the coefficient of friction is 0.4 and the maximum force allowed in the belt is 500N. Calculate the initial belt tension and reason for this.
The figure shows a system with a block m1 attached to a simple square thread screw with a mean diameter of 10 mm, a pitch of 3 mm and whose coefficient of static friction on the thread is 0.35. Block m1 is attached to block m2 by a rope, each of blocks m1 and m2 have a mass of 4 kg.Block m2 is in turn attached to a 15-kg block W by another rope, which passes over a static drum where the coefficient of static friction is 0.20. Determine the required Moment M that must be applied to the screw to start lifting block W. The coefficient of static friction between the surface and blocks m1 and m2 is 0.25. Need free body diagrams
The compressor mechanism shown in Figure bellow is driven clockwise by a DC electric motor at a constant rate of 600 rpm. In the position shown, the cylinder pressure is 45 psi. The piston weighs 0.5lb, and the coefficient of friction between the piston and the compressor cylinder is 0.1. The weight of all other links is negligible. At the instant shown, determine the torque required from the motor to operate the compressor. (the piston acceleration is 5378 in/s2). Image is provided .
PROBLEM The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V-belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=900N), coefficient of friction ų=0.3 4- the speed of large pulley.
The drum shown in the figure below has a weight of 100 N and rests on the floor for which the coefficient of static friction is 0.6. Assume tipping and determine the smallest value of P required for impending motion in N Assume sliding and determine the smallest value of P required for impending motion in N.
Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
A pile-driver hammer has a mass of 300 kg and is to be raised 16 m in 4 sec. The total friction on the guides is constant at 400 N. What constant pull must be exerted on the cable?
A large box of mass m sits on a horizontal floor. You attach a lightweight rope to this box, hold the rope at an angle u above the horizontal, and pull. You find that the minimum tension you can apply to the rope in order to make the box start moving is Tmin. Find the coefficient of static friction between the floor and the box.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
Consider the figure shown in Figure E5.33. You are lowering two boxes, one on top of the other, down a ramp by pulling on a rope parallel to the surface of the ramp. Both blocks move with constant velocity of 15.0 [m/s]. The coefficient of kinetic friction between the ramp and the lower box is 0.444 and the coefficient of static friction between the two boxes is 0.800. a. Draw the Free-Body diagram of both blocks. Set the x axis parallel to the ramp.b. Write the x and y components of 2nd law for both blocks considering their state of motion (accelerations).c. What are the magnitude and direction of the frictional force on the upper box?