The aerodynamic drag of a new sports car is to be predicted at a speed of 60 mph at an air temperature of 25°C. Automotive engineers build a one-third scale model of a car to test in a wind tunnel, shown in the figure below. The temperature of the wind tunnel air is also 25°C. The drag force is measured with a drag balance, and the moving belt is used to simulate the moving ground (from the car's frame of reference). The aerodynamic drag on the model in the wind tunnel is measured to be 34.5 lbf when the wind tunnel is operated at the speed that ensures similarity with the prototype car. Estimate the drag force (in lbf) on the prototype car at the given conditions. For air at T-25°C and atmospheric pressure. p-1.184 kg/m³ and u-1.849-10-5 kg/m-s. Wind tunnel test section Moving belt Pm Pa Drag balance Fo.m

The aerodynamic drag of a new sports car is to be predicted at a speed of 60 mph at an air temperature of 25°C. Automotive engineers build a one-third scale model of a car to test in a wind tunnel, shown in the figure below. The temperature of the wind tunnel air is also 25°C. The drag force is measured with a drag balance, and the moving belt is used to simulate the moving ground (from the car's frame of reference). The aerodynamic drag on the model in the wind tunnel is measured to be 34.5 lbf when the wind tunnel is operated at the speed that ensures similarity with the prototype car. Estimate the drag force (in lbf) on the prototype car at the given conditions. For air at T-25°C and atmospheric pressure. p-1.184 kg/m³ and u-1.849-10-5 kg/m-s. Wind tunnel test section Moving belt Pm Pa Drag balance Fo.m

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.32P

See similar textbooks

Similar questions

5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its bearing is found to be dependent on the force F normal to the shaft, the speed of rotation N of the shaft, the dynamic viscosity of the oil, and the shaft diameter D. Establish a correlation among these variables by using dimensional analysis.
A student team is to design a human-powered submarine for a design competition. The overall length of the prototype submarine is 95 (m), and its student designers hope that it can travel fully submerged through water at 0.440 m/s. The water is freshwater (a lake) at T = 15°C. The design team builds a one-fifth scale model to test in their university’s wind tunnel. A shield surrounds the drag balance strut so that the aerodynamic drag of the strut itself does not influence the measured drag. The air in the wind tunnel is at 25°C and at one standard atmosphere pressure. At what air speed do they need to run the wind tunnel in order to achievesimilarity?
Here, there is a human powered submarine. The length of the submarine is 4.85 m and the hope is it can travel fully submerged through water at 0.440 m/s. The water it is being tested in is freshwater at a Temperature of 15 degrees celcius. The submarine model is built on a 1/5 scale and is built in a wind tunnel. A shield surrounds the drag balance strut so that the aerodynamic drag of the strut itself does not influence the measured drag. Here, the wind in the wind tunnel is at 25°C and at one standard atm pressure. What air speed is needed to run the wind tunnel in order to achieve similarity?
A sphere is moving in water with a velocity of 1.6 m/s. Another sphere of twice the diameter is placed in a wind tunnel and tested with air which is 750 times less dense and 60 times less viscous (dynamically) than water. The velocity of air that will model dynamically similar conditions is
a test tank will be used to measure the drag of a scale model ship 0.8 m long. This model bears full resemblance to a 40 m long prototype ship that was designed to sail at a speed of 10 m / s. a) model speed b) the ratio between model and prototype drag windows c) a ratio between the powers needed to overcome the drag of the model and the prototype take the number of froud into account in your analysis.
A 1:20 scaled-down model of a hydrofoil is tested in a water channel, at a velocity of 0.179 m/s. At this velocity, a drag force of 2.2 N is measured. Determine the drag force of the original hydrofoil, at a velocity of 0.8 m/s.
A student wants to estimate drag force on a golf ball of diameter D moving in air at a speed of U at atmospheric conditions. The student has access to a wind-tunnel and develops a replica of the ball that is 5 times smaller in diameter sets the wind speed 5 times larger than the actual golf ball. Compared to the force on the replica, the estimated drag force on the actual golf ball will be
List and describe the three necessary conditions for complete similarity between a model and a prototype.
The drag force of a new sports car is to be predicted at a speed of 65 mi/h at an air temperature of 25 C. Automotive engineers build a 0.333333333333333 scale model of the car to test in a wind tunnel. The temperature of the wind tunnel air is also 25 C. Determine how fast (in mi/h) the engineers should run the wind tunnel to achieve similarity between the model and the prototype.
A ship 350 m long moves in sea water whose density is 1030 kg/m3 . A 1:120 model of this ship is to be tested in a wind tunnel. The velocity of the wind tunnel around the model is 35 m/s and the resistance of the model is 65 N. Determine the velocity and also the resistance of the ship in sea water. The density of air is given as 1.24 kg/m3 . Take the kinematic viscosity of air and sea water as 0.012 stokes and 0.018 stokes respectively.
While preparing an experiment of a scale model submarine in a wind tunnel, for conditions of dynamic similarity, it is calculated that the wind speed is required to be 120 m/s. Which one of the following options will not help to reduce the air velocity of the wind tunnel? A) Lowering the design velocity of the prototype (full scale) submarine B) Increasing the pressure of the air used in the wind tunnel c) Increasing the size of the scale model D) Decreasing the density of air used in the wind tunnel E) Reducing the temperature of the air used in the wind tunnel
1) Calculate the drag force (unit: N) of a sphere particle in 20°C water. Know the diameter of the particle = 1 cm; the Reynolds number of water = 1; dynamic viscosity of 20°C water = 0.001 kg/ms; velocity of the particle = 0.02 m/s. 2) When calculate the lift coefficient, the area A in the equation is: a) surface area b) planform area c) cross-sectional area d) frontal area 3) The sum of the components of the pressure and wall shear forces (a) in the flow direction is called ____ and (b) in the normal direction is called ____. a) Friction, Pressure b) Lift, Drag c) Pressure, Friction d) Drag, Lift