Answered: The angle on a single-point cutting…

The angle on a single-point cutting tool geometry in which the face of a tool is inclined sideways is known as Back rake angle Side rake angle Side relief angle End relief angle

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter6: Milling

Section6.2: Tools, Toolholding, And Workholding For The Vertical Milling Machine

Problem 2RQ: What type of cutting tool would most likely be used to machine the special long slots in a milling...

See similar textbooks

Related questions

Q: 11. Two cutting tools with tool life equations given below are being compared: Tool 1: VTº-1-150…

Q: Angle between side cutting edge and axis of tool is known as: * Back rake angle Side rake angle Side…

A: Answer: The correct answer is option (c) side cutting edge angle.

Q: Which cutting tool material has the highest hardness? a. Carbide b. Tool steel c. CBN d. HSS

Q: The positive rake angle in a single point cutting tool is used to cut non-ferrous metals and low…

A: Positive rake angle is provided to low strength material, to reduce BUE, for low speed operation

Q: Which is not a surface texture parameter? A) roughness B) cutting length C) array D) wavy E)…

Q: An aluminum hollow shaft 200 mm outside diameter, 100 mm inside diameter and 500 mm length from…

A: Givenoutside dia=200mminside dia=100mmL=500MMN=400rpmfeed rate=0.25mm/rev

Q: dentify the side rake angle (in degrees), from the following single point tool signature…

Q: In a multi point cutting tool the negative rake angle is used for high tensile strength materials.…

A: In multipoint cutting tools, the angle of the rake surface from the reference plane that is normal…

Q: By increasing the feed: A ) Roughness of surface will decrease B) Nose radius will…

Q: Read the sentences given below and Identify the wrong statement. Sentence 1. The advantage of an…

A: Sentence 1. The advantage of an independent chuck is that the work can be centered to high…

Q: ) In a multi point cutting tool the negative rake angle is used for high tensile strength materials.…

A: Positive rake angle tool is used for soft and ductile material and negative rake angle material is…

Q: A twin-spindle drill simultaneously drills one ½-in hole and one ¾" through a 1" wide work piece.…

Q: The angle on a single-point cutting tool geometry in which the face of a tool is inclined sideways…

A: Back rake angle: It is the inclination of the face toward or away from the end or the end cutting…

Q: Which of the following best describes the "cutting plane" of aligned sectional view: It is a…

A: it is a combination of parallel cutting planes

Q: Choose the most appropriate answers. The unit of cutting parameter "Feed"........ Conveyors designed…

A: 1. The unit of cutting parameter "Feed mm/revolution 2. Conveyors designed within a restricted area…

Q: In a multi point cutting tool the negative rake angle is used for high tensile strength materials.…

A: Positive rake angle used for ductile or soft material while negative rake angle used for higher…

Q: The radial distance between the addendum circle of a gear and the dedendum circle of a gear is known…

A: option 4 is correct -Total depth Total depth:- This is the height of a tooth. It is the radial…

Q: Machining Practices Which of the parameters listed below influence the cutting power? Workpiece…

A: Cutting power required fo face milling Pc= d×w×ft×Z×N×Fc60×106×η where d is the depth of cut in mm,…

Q: An aluminum hollow shaft 200 mm outside diameter, 100 mm inside diameter and 500 mm length from…

A: Given data as per question The outside diameter of shaft =200 mm Inside diameter =100 mm Length of…

Q: Read the sentences given below and Identify the wrong statement. Sentence 1. The advantage of an…

A: Independent chuck works as the holding device for the workpiece. It contains 4 independent jaws that…

Q: Lathe operations and processes What is a single point cutting tool? What are the angles to which the…

A: 1) Lathe Operations: Step Turning: Reduction of diameter. Taper Turning: To produce tapered…

Q: The type of taper turning method in which the tool is fed straightly into the work by a straight…

A: We have to determine the proper tapering method.

Q: Answer the following questions by circling True or False. 13. The cutting speed of the hydraulic…

A: As per Bartleby guideline we are allow to give answer of one question at a time so please post other…

Q: In a milling machine the distance the workpiece advances under the cutter is known as Select one: a…

A: Option d is correct.

Q: Main characteristic when cutting Stainless Steel ISO M is: a/ Machining creates high cutting…

A: Option a is correct.

Q: proper Cutting and feed being ant? o we Set the tool just piece center-line h1 mm depth of cut ece…

A: 1 cutting speed and feed is very important parameters in metal removal process because a) it…

Q: Which one of the given options is wrong? A straight, flat surface is created in shaping…

A: Shaping and planing operations produces flat surfaces.

Q: What is the approximate % change in the life, t, of the tool with zero rake angle used in orthogonal…

A: Given: Flank wear∝cot α

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following. )…

A: The most common lathe machining operation is turning. A cutting tool removes material from the…

Q: In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known…

Q: TRUE OR FALSE. IF FALSE WHAT WORD MAKES THE STATEMENT INCORRECT AND WHAT IS THE CORRESPONDING…

A: When the machining of a object is done by the cutting tool then in that case the chip is formed.…

Q: What’s the difference between radial arm and upright drill press? a)Different cutting tool…

A: Given data : radial arm upright drill press

Q: The positive rake angle in a single point cutting tool is used to cut non-ferrous metals and low…

A: Positive rake angle is used to reduce shear strain, low power consumption, low cutting force, Less…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The above question is from manufacturing engineering. The topic is of metal removal rate. There are…

Q: Read the sentences given below and Identify the correct statement. Sentence 1. The advantage of a…

A: Sentence 1. The advantage of a self-centred chuck is that it is easy to work with. Sentence 2. The…

Q: What are the uses of the following types of Chisel? Concrete Chisel Cold Chisel Cape Chisel Bevel…

A: We have to written the uses of the following types of Chisel? Concrete Chisel Cold Chisel Cape…

Q: Chills are used metal . The torch size of ( GTAW ) process is larger than other ( PAW ) process . 5.…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts…

Q: Which one of the given options is right? a)Poor tolerance and surface finish in a part produced by…

A: Solution:

Q: Identify the true statement from the following a. Unit of cutting speed in millimetre per minute b.…

A: There are various terms related to the machining operations, such as cutting speed, feed rate, depth…

Q: In toolbit nomenclature, the point where the primary and secondary cutting edges met. a.…

A: The edge on tool which removes material is known as cutting edge of tool. Single point cutting tool…

Q: This is a machining process for producing internal straight cylindrical surface or profiles with…

A: In this problem, it is asked about the process which makes internal straight cylinderical surface.

Q: Excessive temperature at the cutting tool point will lead to the following: Brittle fracture ، All…

A: Excessive temperature at the cutting tool point is very dangerous.

Q: In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known…

A: In a lathe machine, Cylindrical Workpiece is machined or produced by several operations. Following…

Q: In which cutting process single point cutting tool removes material from a rotating workpiece to…

A: In turning process the workpiece rotates in the lathe machine and the single point cutting tool is…

Q: Increasing the entering angle of the tool affects the vibrations during cutting by:

A: Entering angle is the angle between the leading cutting edge of the tool and surface of the…

Q: Q3:- Choose the Correct answer. (1):- The drilling tool must be with a- High hardness b- Low…

Q: How nuch machlning time required a mild steel rod trom 65mm 58 mm over a length of 100 mm by turning…

A: Given Data ⇒ Initial Diameter of mild steel rod (D)=65 mm Length(L)=100 mm Approach Length(A)=5 mm…

Q: Q1. a. Define a machine tool and list all four functions. b. List all the classifications of machine…

A: Machine tools are used to produce the required size, shape of the work piece. To get the material…

Q: Clapper box is used for _______ during machining. a. Push the tool down during return stroke b. Lift…

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.

Question

14q

The angle on a single-point cutting tool geometry in which the face of a tool is inclined sideways is known as

Back rake angle

Side rake angle

Side relief angle

End relief angle

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

18 ) In a multi point cutting tool the negative rake angle is used for high tensile strength materials. Select one: True False
Generally, to decrease or eliminate built-up edge, _______________________________________. Group of answer choices the cutting speed needs to be decreased tip radius of the tool need to be increased depth of cutting needs to be increased rake angle needs to be increased PreviousNext
Identify the true statement from the following a. Unit of cutting speed in millimetre per minute b. Unit of feed is in meter per tooth c. Unit of cutting speed is in meter per second d. Unit of feed is millimetre per tooth
Which one is not a chief element in metal cutting process? a)Cutting speed b)Nominal cross-sectionall area c)Tool life d)Feed
What is the stroke per minute of a mild steel which cutting speed is 200 fpm having a total length of 16".
a. Give 3 reasons why conventional machining is essential. b. What is the difference between the primary shear zone and secondary shear zone? c. Name a device or procedure used to measure cutting temperature Please type the answers!!
2 1.57 Show that, for the same shear angle, there are two rake angles that give the same cutting ratio.
A single-point cutting tool with 12° rake angle is used to machine a steel work-piece. The depth of cut, i.e. uncut thickness is 0.81 mm. The chip thickness under orthogonal machining condition is 1.8 mm. What is the shear angle.
Differentiate the Branch and Bound Method and Gomory's Cutting Plane Method.
Specify cutting tool angles for a single-point cutting tool and usage of each angle with aid of aclear sketch.
During turning tests, using a cemented carbide tool resulted in a 1‑min tool life at a cutting speed = 4.8 m/s and a 22‑min tool life at a speed = 2.0 m/s. (a) Find the n and C
Which one of the following statements is NOT true? Group of answer choices In orthogonal cutting, the cutting edge of the tool is perpendicular to the cutting direction. Continuous chips are typically formed at high cutting speeds and/or high rake angles. Continuous chips are always desirable because they produce good surface finish. In cutting, chip thickness is always greater than the depth of cut. PreviousNext