How much machining time required to turn a mild steel rod from 65mm to58 mm over a length of 100 mm by turning using a carbide insert. If theapproach length and over run length is= 5 mm, Cutting speed is20 m/minand feed is =0.2 mm/rev, and the depth of cut is 0.5mmD

Given Data ⇒ Initial Diameter of mild steel rod (D)=65 mm Length(L)=100 mm Approach Length(A)=5 mm…

How nuch machlning time required a mild steel rod trom 65mm 58 mm over a length of 100 mm by turning using a carbide insert. If th approach length and over run length is = 5 mm, Cutting speed is = 20 m/m %3D %3D and feed is =0.2 mm/rev, and the depth of cut is 0.5mm D

How nuch machlning time required a mild steel rod trom 65mm 58 mm over a length of 100 mm by turning using a carbide insert. If th approach length and over run length is = 5 mm, Cutting speed is = 20 m/m %3D %3D and feed is =0.2 mm/rev, and the depth of cut is 0.5mm D

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.3: Machining Operations On The Lathe

Problem 5RQ: Calculate spindle RPM and machining time for cutting a 1.5" diameter 4" long at 225 SFPM using a...

See similar textbooks

Related questions

Q: Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final…

Q: A workpiece from AISI 1020 steel will be produced by machining on a lathe. The recommended cutting…

A: Machining is a material removal process in which unwanted material is removed in the form of chips…

Q: Q4 Tool life of a turning tool is given by VTO.12xx=C_at a cutting speed (V) of 25m/min, feed(f)…

Q: In a turning operation on stainless steel, cutting speed = 150 m/min, feed = 0.25 mm/rev, and depth…

A: From the given table write the specific energy for cutting stainless steel.

Q: Calculate the machining time required for making 60 holes on an MS plate of 80 mm thickness with a…

A: Given data⇒ Number of holes (n)= 60 The thickness of Mild steel plate (t)=80 mm Diameter of the…

Q: During turning tests, using a cemented carbide tool resulted in a 1‑min tool life at a cutting speed…

Q: A turning operation uses a 2/64 in nose radius cutting tool on a free machining steel with a feed…

A: Write the given values using suitable variables. Here r signifies nose radius, f signifies feed in…

Q: A cutting tool has a nose radius of 1.8mm find the feed rate for a theoretical surface roughness of…

A: Concept: Surface roughness is measured by center line average. (CLA) CLA = (fxf) / (8 x R) Where f…

Q: 3. A turning operation is carried out on aluminum (100 BHN), the cutting conditions are: v = 5.6…

Q: The face milling cutter of D = 200 mm used to cut a block which is 200 mm = H, 1=480 mm, if f- 0.7…

A: Machine time is the ratio of length divided by cutting speed. Here, Length = length of block +…

Q: 1.10A O50 mild steel bar is being turned at 1.70 revis on a multi-tool center lathe having nine…

Q: 1. An engine lathe is used to turn a cylindrical work part, cutting speed 2.2 m/s, feed 0.25 mm/rev,…

Q: A cylindrical work bar with 4.5 in diameter and 52 in length is chucked in an engine lathe and…

A: (a) The depth of cut is, d = 0.125 in. (b) The required feed is, f = 0.010 in/rev. (c) The cutting…

Q: In a turning operation on carbon steel with hardness- 175 HB. the cutting speed - 225 m/min, feed-…

A: GivenV=225m/minf=0.25mm/revd=7.5mmη=90% Cutting energy for Brinell hardess 175Hb=1.6J/mm3U=1.6J/mm3

Q: Q.4 (i) Find the time required for taking a complete cut on a plate 600 × 900 mm², if the .cutting…

A: As per the bartleby policy we can solve the only first question from the multiple questions. Q.4 (i)…

Q: A 12" x 4" block of soft aluminum alloy (u, = 2.5 hp.min/in³) is face milled at a depth of cut of…

A: Given Data: Depth of cut DC=18inch Length of block l=12 in Breadth of block b=4 in ut of aluminium…

Q: As the cutting speed for mild steel is 100ft/min and RPM is 1000, find the diameter of the cutting…

A: Given data as per question cutting speed = 100 ft/min Speed =1000 Feed rate =0.002 in v=100…

Q: Example 3.18 A low carbon steel bar of 147 mm diameter with length of 630 mm is being turned with…

A: Given data as per the question A low carbon steel bar of 147 mm diameter with a length of 630 mm

Q: H.W. The face milling cutter of D= 200 mm used to cut a block which is 200 mm = H, 1 =480 mm, if f=…

Q: (b). A hole of 30 mm diameter and 75 mm depth is to be drilled. The suggested feed is 1.3 mm per rev…

Q: 17) A50-mm-dia endmill cuts 6061 aluminum with 30% tool engagement at a depth of 6 mm. The tool…

Q: A drilling operation is to be performed with a 12.7 mm diameter twist drill in a steelwork part. The…

A: givendiameter of twist drill d=12.7mmdepth of hole h=60mmpoint angle 2α=118ocutting speed…

Q: 1.10A O50 mild steel bar is being tumed at 1.70 revis on a multi-tool center lathe having nine…

Q: Aluminum bar with 100mm diameter and 500mm long is turned down to 88mm diameter, using two passes on…

Q: An orthogonal cutting operation is being carried out under the following conditions: t0-D0,38 mm,…

A: Given data:-uncut chip thickness, t=0.38mmchip thickness, tc=0.65mmwidth of cut, b=2.5mmcutting…

Q: (j) In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 250 m/min,…

A: Given data : stainless steel with hardness = 200 HB cutting speed (v) = 250 m/min feed (f) = 0.3…

Q: In a turning operation on cast iron, the nose radius on the tool = 1.5 mm, feed = 0.22 mm/rev, and…

A: Given data: Nose radius of the tool = 1.5 mm Feed = 0.22 mm/rev Speed = 1.8 m/s Need to determine…

Q: In a turning operation on low carbon steel with hardness = 135 HB, the cutting speed = 180 m/min,…

Q: 1. In a production turning operation, the cylindrical workpiece is 425 mm long and 190 mm in…

Q: The end of a large tubular workpart is to be faced on a NC vertical boring mill. The part has an…

Q: A straight turning operation is carried out using a single point cutting tool on an AISI 1020 steel…

A: Given data: The feed rate is f = 0.2 mm/rev. The depth of cut is d = 0.5 mm. The side cutting edge…

Q: the rod to 16 mm and also facing operation on both sides is done. Assume cutting speed is 30 m/min…

A: Given, L = 120 mm d = 35 mm V = 30 m/min f = 0.7 mm/rev

Q: A part to be turned in an engine lathe must have a surface finish of 1.6 mm. The part is made of a…

Q: 2 1.63 With a carbide tool, the temperature in a cutting operation is measured as 650K when the…

A: Given: feed = 0.05 mm/rev T1=650 K

Q: b) A mild steel having length of 350mm and diameter of 12.5 cm, is being reduced to diameter 9.5 cm,…

Q: Q3 A) A shaft with 150mm in diameter and 1 m length is to be turned in an engine lathe. Cutting…

Q: D. 0.250" D, = 0.125" L-6.250" If Cutting speed v=211 FPM (feet per minute) and f= 0.0018 in/rev;…

A: Cutting speed v=211 ft/minor v=211×12 =2532 in/minf=.0018 in/revD0=.250''Df=.125''L=6.250''

Q: In turning of stales steel alloy, 1100 mm length and 400 mm diameter, the Feed was 0.35 mm/rev, and…

Concept explainers

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.

Question

How much machining time required to turn a mild steel rod from 65mm to
58 mm over a length of 100 mm by turning using a carbide insert. If the
approach length and over run length is
= 5 mm, Cutting speed is
20 m/min
and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The vertical band saw is particularly useful, as it can be used to make straight cuts as well as ______________.
Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final length (L1) 120mm to 58 mm by turning a carbide insert. If the approach length and over run length are 5 mm and 1 mm respectively, take Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
Find the machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm by using a carbide insert. If the approach length and over run length is taken as 5 mm, Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
If a fairing operation is executed at a rotational speed of 40.0 rev / min, the feed is 0.015 in / rev and the depth of cut is 0.180 in, it determines: a) cutting time to complete the fairing operation; and b) the cutting speed; and c) The speed of metal removal at the beginning and end of the cut d) The power dissipated.
A part to be turned in an engine lathe must have a surface finish of 1.6 μm. The part is made of a free machining aluminum alloy. Cutting speed = 150 m/min. The nose radius on the tool = 0.75 mm. Determine the feed that will achieve the specified surface finish.
(j) In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 250 m/min, feed = 0.3 mm/rev, and depth of cut = 8 mm. How much power will the lathe draw in performing this operation if its mechanical efficiency = 95%. Use Table below to obtain the appropriate specific energy value.
A bar of 70 mm diameter is being cut orthogonally and is reduced to 68 mm by cutting tool in case mean length of the chip is 68.9 mm. find the cutting ratio determine shear angle also if the rake angle is 10 degree.
A single-point cutting tool with 12° rake angle is used to machine a steel work-piece. The depth of cut, i.e. uncut thickness is 0.81 mm. The chip thickness under orthogonal machining condition is 1.8 mm. What is the shear angle.
A turning operation uses a 2/64 in nose radius cuttingtool on a free machining steel with a feed rate = 0.010in/rev and a cutting speed of 300 ft/min. Determine thesurface roughness for this cut.
5.) Calculate the machining time required to reduce from 60mm diameter shaft to 50mm diameter, for a length of 1500mm with depth of cut 2mm for rough cut and 1mm for finish cut. Cutting speed and feed may be assumed as 30m/min and 0.5mm/rev respectively.
A cylindrical workpiece has a 14.0 in diameter and has 30 in long. It is to be turned in an engine lathe at the following cutting conditions: cutting speed = 400 ft/min, feed = 0.015 in/rev, and depth of cut = 0.150 in. Determine the time to complete one turning pass if the approach and overtravel allowances are each 0.25 in (total = 0.50 in). Note: 1 ft = 12 in
During orthogonal cutting of MS with a 10 ° rake angle tool, the chip thickness ratio was obtained as 0.4. Calculate shear angle