The arm in the figure below weighs 37.6 N. The force of gravity acting on the arm acts through point A. Determine the magnitudes of the tension force F, in the deltoid muscle and the force i, exerted by the shoulder on the humerus (upper-arm bone) to hold the arm in the position shown. (Enter your answers to at least the nearest newton.) N %3D 0.080 m 0.290 m-

The arm in the figure below weighs 37.6 N. The force of gravity acting on the arm acts through point A. Determine the magnitudes of the tension force F, in the deltoid muscle and the force i, exerted by the shoulder on the humerus (upper-arm bone) to hold the arm in the position shown. (Enter your answers to at least the nearest newton.) N %3D 0.080 m 0.290 m-

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.11P: A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and...

See similar textbooks

Similar questions

Determine the force in the cable OC and the elongation of the spring OA, OB necessary to support a box of mass (M) 400 kg as shown in the figure below. If a = 4 m, b = 5 m, c = 3 m, k1= 5000 N/mm and k2= 4000 N/mm. NB: All calculation must be in Newton (N) and please include FBD
A horizontal board weighing Wb = 600 N is hinged to a vertical wall. A personweighing Wp = 400 N stands at the end of the board 5 m from the wall. A rope is attached to theboard at a point 3 m from the wall and makes an angle of θ = 40° with theboard. Determine the tension (T) in the rope
A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0,respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the leftend where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) andthe weight (W) of the bar
Physics for Engineering A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.)
Two bars are subjected to F=20 kN force as shown in Figure and atemperature rise of 100 0C. DetermineReaction forces at the walls A and B. The change in length of the bronze bar
A 25kg wooden plate is held in place by two strings attached to the ceiling and the wall. The string attached to the ceiling makes an angle 40o with the horizontal and the string attached to the wall makes 90o with the wall. Determine the force in each string (DONT ANSWER THIS PROBLEM). ANSWER ONLY THE PROBLEM IN THE ATTCHED IMAGE, COMPLETE SOLUTION PLEASE.
A vertical load P = 800 lb applied to the tripod shown in the figure, causes a compressive force of 256 lb in leg AB and a compressive force of 283 lb in leg AC. Determine the force in leg AD and the coordinates xD and zD of its lower D. Answers: AD = 433 lb; xD = 4ft; zD = 1 ft
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has the following properties: R = 90 mm, n =4 turns, G = 70 GPa, d = 30 mm, and allow = 105 MPa while Member AC has the following properties: L = 2 , A = 500 mm2, E = 200 GPa, and allow = 30 MPa. Determine the maximum safe value of W (in N). Use simplified formula for the helical spring.
Determine the force in each member of the truss (positive value for tension and negative for compression). Given: P1 = 20 N, P2 = 10 N.
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure, choose the alternatives that are true. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N If the plate had a weight of 332N (applied vertically downwards in the center of the plate), the reaction Dy on the plate should be vertical downwards so that the plate still remained in balance in that position. True or false?
A 40 kg-mass hangs from the end of a uniform beam. The beam is 6.0 m long and has a mass of 60 kg. The beam is supported at the left end by a hinge at the wall and by a cable at the right end. The other end of the cable is tied to the wall at a point 4.0 m above the left end of the beam. (g = 9.81 m/s² )A. Draw the FBD;B. Find the tension (T) in the supporting cable in Newtons; andC. Find the reaction force (R) of the hinge on the beam ( magnitude and direction).