The average shear stress in each of the 6-mm diameter bolts and along each of the four shaded shear planes is not allowed to exceed 80 MPa and 500 kPa, respectively. Determine the maximum axial force P that can be applied to the joint

Q: The drive shaft of a car with diameter 30 mm is designed to transmit a power of 50 kW when rotating…

A: Given data       d=30mm       P=50kw       N=2100rpm        τ=230MPa.     To find    1) τmax…

Q: The torque of 12kN m is applied to the 6-meter steel shaft's free end. The shaft must rotate at a…

A:

Q: 1.3 Define the terms shear stress and shear strain, illustrating your answer by means of a simple…

A: Shear stress – When an object is subjected to an equal and opposite force, then one layer will slide…

Q: The extruded plastic shape has dimensions of D = 37 mm, d = 33 mm, a = 91 mm, and t = 7 mm. (a)…

A:

Q: A solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the…

A: given data;load=mg=25*9.81=245.25Nlimiting stress σ=27.24kpa=27240Pa=27240N/m2cross sectional…

Q: Members in Direct Shear A belt pulley used to drive a device is attached to a 30-mm diameter shaft…

A: Note:- As per our company guidelines we are supposed to answer only the first three sub-parts.…

Q: 1. A circular piece of wood, 90mm in diameter, is used as a compression block. Determine the axial…

A:

Q: A 200-mm-diameter pulley is prevented from rotating relative to 60-mm-diameter shaft by a 70-mm-…

A: Find the width of key.

Q: force Q of magnitude 9 kips is applied to the machine element AB as shown. The uniform thickness of…

A:

Q: Since each of the shafts AB, BC and CD shown in the figure consists of a solid circular bar,…

A: Given data: The diameter of the part AB is dAB=15 mm The diameter of the part BC is dBC=18 mm The…

Q: At point A & C, the beam is pin connected. Therefore, find the average normal stress in the…

A:

Q: 1. The handwheel shown consists of the shaft, flange, and handle. A force P = 1 kN is applied to the…

A:

Q: Q2) The two portions of member AB are glued together along a plane forming an angle 0 with the…

A:

Q: Q2/ The assembly consists of two sections of cast-iron rod connected together using a reducing…

A: Given data :- for section AB L = 12 in , d = 0.75 in for section BC L = 15 in , d = 1 in shear…

Q: Plot the shear-stress distribution over the cross section of a rod that has a radius c. By what…

A: Shear force acts parallel to the plane or we can say that perpendicular to the centroidal axis.…

Q: Construct the shear-force diagram and identify the largest negative shear force. Assume a = 5.9 ft,…

A:

Q: The torque shown in the figure is exerted on pulleys A, B and C. If it is known that the AB axis is…

A:

Q: (a) Which of the following drive shafts experiences a larger maximum shear stress caused by…

A:

Q: In the hanger shown, the upper portion of link ABC is 3/8 in. thick, and the lower portions are each…

A:

Q: The average shear stress in each of the 6-mm diameter bolts and along each of the four shaded shear…

A: As per given data The average shear stress in each of the 6-mm diameter bolts and along each of the…

Q: A flanged bolt coupling consists of nine ½ -in diameter bolts equally spaced around a bolt circle 15…

A: The torque capacity of the coupling is 5.522 kip•ft.

Q: The hydraulic cylindere has an innner diameter of 100 mm and wall thickness of t= 4mm. If it is made…

A: Solution: Given Data: d=100 mmt=4 mmσall=146 MPa   To Find: Magnitude of Force P.

Q: 1. Determine the maximum and minimum shear stresses developed in the hollow circular shaft, which…

A:

Q: The extruded plastic shape will be subjected to an internal shear force of V= 380 Ib. Dimensions of…

A:

Q: he ends A and D of the two solid shafts AB and CD are fixed, while the ends B and C are connected to…

A: Given:dAB=60 mmrB=100 mmrc=40 mmdCD=45 mmζallow=50 MPa

Q: Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which…

A: Given data: ◆ The bolt circle diameter: D = 250 mm ◆ The number of bolts: n = 12 bolts ◆ The…

Q: Q16/ The value of the normal stress due to axial force 2 kN applied on the * :beam is Point D 10 kN…

A: Find the normal stress due to axial load 2kN and due to flexural load 10 kN.

Q: The compound shaft is composed of bronze cylindrical segment AB and steel cylindrical segment BC.…

A:

Q: B 150 lb magnitude is applied to end C of lever ABC. Determine the shearing stresses on an element…

A:

Q: The device shown is used for determining the shear strength of the wood. The dimensions of the wood…

A:

Q: Four plates, each being 15 mm thick, are to be connected by six bolts of 19 mm diameter as shown.…

A:

Q: The solid rod with radius r=37 mm is subjected to the loading F;=120 kN, F2=38 kN, F3=29 kN. With…

A: Fifth option is correct combined shear stress=4.805Mpa

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

A:

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A: To know the variation and maximum value of shear force and bending moment, V and M diagram are…

Q: The extruded plastic shape has dimensions of D = 24 mm, d = 20 mm, a = 87 mm, and t = 6 mm. (a)…

A:

Q: The stress induced in a body, when subjected to two equal and opposite forces which are acting…

A: Shear stress: When two equal and opposite forces that are acting tangentially across the resisting…

Q: 3. (A). Define the terms shear stress and shear strain, illustrating your answer by means of a…

A:

Q: Use the diagram below to answer questions one and two. 100 m Q2. The average shear stress in each of…

A: Write the given data with suitable variables: d=6 mmζ=80 MPaσc=500 kPa=0.5 MPa1000 kPa1 MPa

Q: Part 2 Determine the shear force acting at each of the following locations: (a) x = 11.5- ft (i.e.,…

A:

Q: 1. The handwheel shown consists of the shaft, flange, and handle. A force P = 1 kN is applied to the…

A:

Q: 1. Each of the four vertical links has a 8 x 36-mm uniform rectangular cross section and each of the…

A: Given:The cross-section area of each vertical four links, A = 8 mm x 36 mmThe diameter of each pin,…

Q: The square deforms into the position shown by the dashed lines. Determine the shear strain at each…

A:

Q: How many 10-mm diameter rivets is needed to fasten member BF to the gusset plate at B if the member…

A:

Q: Q2/ The assembly consists of two sections of cast-iron rod connected together using a reducing…

A: given data diameter of AB = 0.75 in length of AB = 12in diameter of BC = 1 in length = 15 in G = 5.5…

Q: The extruded plastic shape has dimensions of D = 24 mm, d = 18 mm, a = 87 mm, and t = 3 mm. (a)…

A: Given data as per question D =24 mm d =18 mm a =87 mm t =3 mm V =335 N Considering section 1 and 2…

Q: The vertical members AB and CD have a shear modulus G = 3.7x10^6 psi. Determine: the maximum shear…

A:

Q: typical method of temporarily securing a steel beam onto a column is by using a seat angle with…

A:

Q: Assume that a 20mmø rivet joins the plates that are each 110mm wide. The allowable stresses are 120…

A:

Q: Determine the length of the shortest 2-mm diameter bronze wire, which can be twisted through two…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.