A hollow circular shaft has an external diameter of 0.120 m and the internal diameter а) is three-fourths the external diameter. If the stress at a fiber inside is 36 MPa, due to a torque T applied, analyze i. this torque, ii. the maximum shear stress, and iii. the angle of twist per unit length.

A hollow circular shaft has an external diameter of 0.120 m and the internal diameter а) is three-fourths the external diameter. If the stress at a fiber inside is 36 MPa, due to a torque T applied, analyze i. this torque, ii. the maximum shear stress, and iii. the angle of twist per unit length.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: You have a wind turbine with a maximum power rating of 5 MW available for use in a wind farm. This…

A: The wind energy is produced when the turbine is moving with the help of wind. The power produced by…

Q: Consider the Gulfstream IV flying at Mach = 0.8 at an altitude with atmospheric pressure of…

A: Given data Speed of aircraft = 0.8 Mach Altitude Pressure = 33283.40 Pa Weight = 73000 lb = 33112.24…

Q: For a point under a plane state of stress, the stresses on the vertical and horizontal planes are…

Q: Air enters a compressor operating at steady state at 14 lbf/in2, 60°F, with a volumetric flow rate…

Q: Sketch the shear force and bending moment diagrams. Neglect the weight of the beam. y 15 kN 30 kN -2…

Q: Given the image below, what is the equilibrium equation the correctly relates the tension forces…

A: Given

Q: At a given instant the wheel of radius r = 0.8 m is rotating with angular velocity w = 3 rad/s and…

Q: Mass = 1.6kg is hung from a spring. Static displacement is 1.4cm. The top support is pushed in a…

Q: Determine the surface tension of liquid in contact with air and a glass tube, If the capillary tube…

Q: For the cantilever beam shown on the above figure, determine the following: with complete…

Q: At the Niagara Falls generating station, the water drops 102 m from the intake pipes at the top of…

A: Given data Height (H) = 102 m Mass flow rate (m˙) = 1000 kg/s Efficiency of the turbine (η) = 75% =…

Q: The weight of the bicycle is 29 Ib with center of gravity at G. Determine the normal forces at A and…

Q: A 120° reducing bend is placed in a horizontal plarje such that the inlet is inclined 30° to the…

Q: Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: Given data as per question Each grid slide=16 MPaFor a point in a physical object that is subjected…

Q: A prototype engine was built and tested, during the non-flow process it is observed that the Work…

A: (a) Write the given data. w=80 ftlbf/°FT1=220 °C=428 °FT2=475 °C=887 °FU=25+0.7t

Q: An universal coupling is used to connect two mild steel shafts transmitting a torque of 6000 N-m.…

Q: A simply supported wood beam of length L = 8 ft carries a concentrated load Pat midspan, as shown.…

Q: 1. Evaluate the following expressions in terms of v, p, T, Cp, and Cv, then simplify them for an…

Q: You have been selected by an engineer for them to design their newest robotic prototype. As of this…

A: The first version of any machine, including robots, is called a prototype. Following the creation…

Q: 2. An automatic bending machine requires a very large torque and slow rpm. Suppose you are to design…

A: It is asked to reduce the RPM from 1400 RPM to 18 RPM by using spur gear combinations

Q: A pump is used to increase the pressure of the water entering the boiler of the steam power cycle.…

Q: The steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. is carrying a load P=…

Q: An inward flow reaction turbine has outer and inner diameters of the wheel as 1 m and 0.5 m…

Q: Determine the surface tension of liquid in contact with air and a glass tube. If the capillary tube…

A: The surface tension of a liquid in contact with air and a glass tube must be determined.When a…

Q: 2. The water-park ride consists of a 900-lb sled which slides from rest down the incline and then…

Q: A cylindrical tank contains water to a depth of 0.90 m. What is the resulting pressure in kPa at the…

Q: A 37.5-mm-diameter rod 6 m long elongates 12 mm under a load 236 KN. The diameter of the rod…

Q: PARTE B: Realice la siguiente transtormación de estuerzos y represente sus respectivos planos, Valor…

Q: A cantilever timber beam with a span of L = 3.5 m supports a uniformly distributed load w. The beam…

Q: Determine the specific weight of air at 760 mmHg absolute and 22C?

A: Note: (1 mmHg = 133.322 Pa)

Q: At the instant shown, drum D rotates at a constant angular velocity of 10.00 rad/s counterclockwise.…

Q: Determine the volume of 5.5 kg of dry saturated steam at 1 100 kPa

A: Dry saturated means x=1, Find, volume

Q: A pressure gage 7.0 m above the bottom of a tank containing a liquid reads 64.94 kPa; another gage…

A: Soln:- h1 = 7m P1 = 64.94kpa h2= 4m P2 = 87.53 kpa ∆P = pg∆h (87.53-64.9)…

Q: A piston cylinder contains 1 kg of liquid water at 20°C and 300 kPa. There is a linear spring…

Q: Match the following logic operators with their corresponding descriptions. Select- Select-- &&…

A: To find : match the following logic operators with their corresponding description

Q: Problem 7: On a hot day, the freezers in a particular ice cream shop maintain an average…

Q: 5 m 30°

Q: A SYStem executes a power cycle while recieving 750 k) by heat transfer at a temperature of 1500°k…

A: GivenQ1=750kJT1=1500kQ2=-100kJT2=500KQ3=?T3=1000K

Q: 2. Locate the centroid of the area bounded by the axis & the sine curve y= asin rox/L from 0 to L y=…

Q: 7.3 Fluid fills the space between two parallel plates. The differential equation that describes the…

A: Given Differential equation to describe the flow To obtain: Normalized form of the equation and…

Q: Consider a thermometer in Fahrenheit scale and Celsius scale, both thermometers are immersed in a…

A: As we knowFahrenheit F=95C+32

Q: Shear force at B - ______ lbs Shear force as function of x - ______ lb Bending moment as function of…

A: To determine the shear force and bending moment for the given loading

Q: y a - х a = 9 in b = 1.3 in с %3D 2.3 in

Q: A flanged protective type coupling is required to transmit 50 kW at 2000 r.p.m.. Find : (a) Shaft…

Q: A uniform ladder 4.8 m ft long and weighing W lb is placed with one end on the ground and the other…

Q: 3. Draw the load and the bending moment diagrams that correspond to the given shear force diagram in…

Q: Tap water is contaminated with E. coli!! To make sate drinking snow at -5.0°C using the stove that…

A: Givenm=9.8kgT1=-5oCQ=2290WCsmow=2090 J/kgoCCwater=4186 J/kgoCLf=3.4×105 J/kgLV=2.3×106 J/kg

Q: An automobile lift raises a car weighing 3000 lbf, 6 ft off the shop floor (Fig. 2-12). Assuming the…

A: Weight of the car, Wcar= 3000 lbf Weight of the lift, Wlift= 500 lbf Distance to be moved off the…

Q: 9-In an ideal dual combustion cycle conditions at the commencement of the adiabatic compression are…

Q: Air enters a two-stage compressor operating at steady state at 520°R, 14 Ibf/in.2 The overall…

Question

G = 85 MPa

A hollow circular shaft has an external diameter of 0.120 m and the internal diameter
а)
is three-fourths the external diameter. If the stress at a fiber inside is 36 MPa, due to
a torque T applied, analyze
i. this torque,
ii. the maximum shear stress, and
iii. the angle of twist per unit length.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A full circular cross-section shaft will be designed to provide power transmission at 220 (revolution/minute) revolution of a 12300 kW engine. Since the shaft length is 3 m, the material shear modulus is 80 GPa, and the shear yield stress is 190 MPaa) How many kN.m torque should the shaft carry?b) Write down the minimum safe shaft radius in metersc) How many rad is the shaft at the specified minimum radius. found?
Consider a hollow steel shaft with a 130mm outside diameter and a 70mm inside diameter. What is the maximum torque that this shaft can transmit if the shear yield stress is 1.4 x 108Pa and the behavior is elastic, perfectly plastic?
A hollow shaft with external and internal diameters 100 mm and 75 mm respectively transmits 500 kW at 1 500 r/min. If the measured angle of twist in a length of 3,5 m is 1,17°, calculate the shear strain at the inner and outer radii and the modulus of rigidity of the shaft material.
A shaft capable of transmitting 50 kW of power will spin at 100 revolutions per minute. The maximum twist allowed in a 3m length of shaft is 1.5 degrees. If the maximum torque is 30% more than the average or mean torque. Assume a fully elastic action and a modulus of rigidity of G=135 GN/m2 for the shaft material. Calculate the shaft's diameter and the shaft's maximum shear stress
A simply supported beam, 50mm wide by 100mm high and 300 mm long is subjected to a concentrated load of 3000 N at a point 100 mm from one of the supports. Find the maximum fiber stress.
A hollow aluminum tube used is a roof structure has an outside diameter d2=70mm and inside diameter d1= 50mm. The tube is 2.5m long and the aluminum has a shear modulus of G=28 GPa. a.) If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist in degrees when the max shear stress is 50MPa? b.) What diameter 'd' is required for a solid shaft to resist the same torque with the same maximum stress?
If The section below is subjected to bending moment of 30kN.m (causing compression on the top fiber) and shear force of 20kN acting downward, find the depth of the neutral axis x-x (d)?the moment of the inertia about x-x axis?the maximum tensile bending stress?the maximum shear stress?
A hollow aluminium tube used in a roof structure has an outside diameter 104mm and an inside diameter 82mm. The tube is 2.75m long and the aluminium has shear modulus G=28GPa. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist (in degrees) when the maximum shear stress is 48 MPa. What diameter d is required for a solid shaft to resist the same torque with the same maximum stress. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?
For a given material, Young’s modulus is 100GPa and shear modulus is 40GPa. Find the bulk modulus and lateral contraction of a round bar of 40mm diameter and 2.5 m long when stretched 2.5 mm.
The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in diameter and shear modulus G of 80,000 MPa is:
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
A solid shaft 18 m Length is to transmit power at 2200 rpm. If the shaft is stressed to 275 MPa when twisted at 40⁰, what should be the design diameter in ( mm) of the shaft and the maximum power transmitted in kW? Use shear modulus G = 100 GPa.