The average shear stress in each of the 6mm-diameter bolts cannot exceed 80 MPa. Furthermore, the average shear stress along the failure planes (highlighted) in the wood cannot exceed 500 kPa. Determine the maximum axial force that can be applied to the joint. 100 mm

The average shear stress in each of the 6mm-diameter bolts cannot exceed 80 MPa. Furthermore, the average shear stress along the failure planes (highlighted) in the wood cannot exceed 500 kPa. Determine the maximum axial force that can be applied to the joint. 100 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Determine the minimum cross-sectional area of a steel bar required to support a tensile force of 50…

A: Given Data⇒Tensile Force=50 KipsAllowable unit tensile stress=20 KsiProblem definition⇒Problem says…

Q: The yoke-and-rod connection is subjected to a tensile force P. The end of the 40-mm diameter rod is…

Q: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube…

A: Given data: F=600 Ndi=25 mmt=5 mm Need to determine the maximum shear stress in the tube.

Q: The five-bolt connection must support an applied load of P = 4400 lb. If the average shear stress in…

Q: The tension member is fastened together using two bolts, one on each side of the member as shown.…

A: Given data: Diameter of bolt, d = 0.3 in. Shear stress, τ = 12 ksi Normal stress, σ= 20 ksi The free…

Q: Determine the load which will cause a total deformation of 0.036 inch to a stell rack which has a…

Q: The five-bolt connection must support an applied load of P = 1500 lb. If the average shear stress in…

Q: Determine the allowable weight that the assembly can handle if the cable AB has a working stress of…

Q: The plate welded to the end of the l-beam is fastened to the support with four 10-mm-diameter bolts…

Q: 25 kN 20 kN 30 kN 14 -1.5 m- 3 m 3 m

Q: Determine the allowable weight that the assembly can handle if the cable AB has a working stress of…

Q: Two pieces of wood, 2 in. by 4 in., are glued together along the 40° Joint. Determine the maximum…

Q: The bellcrank is in equilibrium a) determine the diameter of the bar DE if the normal stress is…

A: GIVEN: Load W= 30KN length of road BC:LBC=0.2m length of road CD:LCD=0.3m thickness of plate C: t=…

Q: The lap joint is fastened by 20 mm rivets placed alongside each other as shown along the length of…

Q: The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear…

A: Given data as per the question Applied load =370 KN Average shear stress =200Mpa

Q: The steel bracket is used to connect the ends of two cables. If the allowable normal stress for the…

A: Given data

Q: The supporting wheel on a scaffold is held in place on the leg using a 4-mm-diameter pin. If the…

A: Given Data: The diameter of the pin is D = 4 mm. The normal force is F = 3 kN Assuming double…

Q: 5. The wood pole is supported by two cables of 4 -in. diameter. The turnbuckles in the cables are…

A: Givencable's diameter dcb=14instress in cable σcb=80000psiworking copressive stress for wood…

Q: The five-bolt connection must support an applied load of P = 3900 lb. If the average shear stress in…

Q: The average shear stress in each of the 6-mm diameter bolts and along each of the four shaded shear…

A: As per given data The average shear stress in each of the 6-mm diameter bolts and along each of the…

Q: The joint fastend togather using two bolts with the plate thickness of 5mm. Determine the required…

A: given; shear stress of bolt(τ)=350MPalets take diameter of bolt=dacting load on plate(P)=40KN

Q: The tension member is fastened together using two bolts, one on each side of the member as shown.…

A: Please find the answer below

Q: A 2" diameter pin connects the three links as shown. The links have a 3" by 3" cross- section.…

Q: Determine the shear stresses experienced by the four identical circular bolts of diameter 20 mm used…

A: Given data: F = 150 kN d = 20 mm Need to determine the shear stress in each bolt.

Q: Question 1: Rods AC and BC are used to suspend the 200 kg mass. If each rod is made of a material…

A: Given data :- Mass = 200 kg Stress = 150 mpa Find :- Min req diameter= ?

Q: The two pieces of wood, 150mm x 200mm, are glued together along the 55° joint. Determine the maximum…

Q: Q1/ The yoke-and-rod connection is subjected to the load shown below. Determine to the nearest one…

A: Calculate the permissible normal stress in the rod. Here, is the permissible normal stress in the…

Q: determine the minimum bolt diameter that may be used for this connection.

Q: Question: Determine the average shear stress in the single pin A and double pin B as well as the…

A: The UDL can be converted to point load by taking the area of the applied load surface and point it…

Q: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube…

Q: The five-bolt connection must support an applied load of P = 4600 lb. If the average shear stress in…

Q: The member is to be made from a steel plate that is 0.25 in. thick. If a 1-in. the hole is drilled…

A: Calculate the approximate width w of the plate…

Q: The steel end-cap is fitted into grooves cut in the timber post. The working stresses for the post…

Q: The two pieces of wood, 2 in. by 4 in., are glued together along the 40° joint. Determine the…

A: First we have calculated the area of glued plane, then using simple trignometry we have calculated…

Q: 11. Problem 5: The links of the chains are made of steel that has a working stress of 300 MPa in…

Q: The rigid block has a weight of 100 kip and is to be supported of steel (A and C) and brass(B) posts…

Q: An axial force of 52 kN is applied to the assembly shown by means of rigid end plates. 5 mm 5 mm 20…

Q: determine the average normal stress developed in each post when post B is heated so that its…

Q: The small-block has a thickness of 0.5 in. If the stress distribution at the support developed by…

A: The thickness of the block is b=0.5 in. The length of the block is l=1.5 in. The smaller stress…

Q: The lap joint is connected together using a 30 mm diameter bolt. If the bolt is made from a material…

A: Given data: The diameter of the bolt is d=30 mm The applied force on the plate is P=750 kN=750×103 N

Q: Rods AC and BC are used to suspend the 200-kg mass. If each rod is made of a material for which the…

A: Given data: Maximum allowable normal stress, σmax = 150 MPa. Mass of the suspended block, m = 200…

Q: Determine the largest load P that can be applied to the frame without causing either the average…

A: To find out the angle between AC and CB tanα=ABAC=21.5α=53.13°

Q: applied load of P = 480 N causes the upper frame to be deflected downward by 4.9 mm. Determine the…

Q: Determine the maximum compressive force that can be applied on a circular member of diameter 40 mm.…

A: Given, Diameter of the circular section , d = 40 mm. The compressive strength of the member ,…

Q: An axial load is applied to the rectangular cross section bar which is welded at the 57 degree angle…

A: Given: P= 180 kN σf=160 MPaτf=90 MPaFOS=2.3 θ=90°-57°=33°

Q: The two portions of member AB are glued along a plane forming an angle 0 = 65°with the horizontal.…

Q: Determine the thickness of a 130 mm wide uniform plate for safe continuous operation if the plate is…

Q: Determine the maximum normal stress developed on the cross section of the supporting member at…

A: Given Data: The load is W=580 lb. The eccentricity is e=1.5 ft. The radius of the cross-section is…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

The average shear stress in each of the 6mm-diameter bolts cannot exceed 80 MPa.
Furthermore, the average shear stress along the failure planes (highlighted) in the wood cannot
exceed 500 kPa. Determine the maximum axial force that can be applied to the joint.
100 mm
100 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The five bolt connection must support an applied load of P = 2000 lb. If the average shear stress in the bolts must be limited to 32 ksi, determine the minimum bolt diameter that may be used for this connection.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (sY)st = 640 MPa, and for the bronze (sY)br = 520 MPa,determine the magnitude of the largest elastic load P that can be applied to the assembly. Est = 200 GPa, Ebr = 100 GPa.
The pipe assembly shown is subjected to a force F = 400 N. The pipe has an inner diameter of 20 mm and an outer diameter of 30 mm. It is made of steel with Sy = 250 MPa. Determine the safety factor at point A using the maximum shear stress theory. Select one: a. NA = 1.843 b. NA = 3.224 c. NA = 2.580 d. NA = 4.299
two steel plates are held together by two bolts. a)determine the required diameter of the bolts if the failure shear stress is 300MPa using a factor of safety of 2. b)using the answer from a, determine the steel plates thickness if the failure bearing stress of the steel is 350MPa using factor of safety as 1.5
Determine the thickness of a 130 mm wide uniform plate for safe continuous operation if the plate is to be subjected to a tensile load that has a maximum value of 260 kN and a minimum value of 110 kN. The properties of the plate material are as follows: Endurance limit stress = 235 MPa, and Yield point stress = 310 MPa. The factor of safety based on yield point may be taken as 1.4.
Two bolts are used to lap joints two steel plates. The tensile force on the plate is 40 kN. Determine the required diameter of the bolts if the failure shear stress of the bolts is 350 MPa. Use a factor of safety for shear equal to 2.5.
An axial load is applied to the rectangular cross section bar which is welded at the 57 degree angle shown. If the weld material has a failure normal stress of 160 mPa and a failure shear stress of 90 mPa, determine the required thickness if a factor of safety of 2.3 is required. Also determine the required diameter of the bolts(to the nearest mm) if the plate is face bolted to the supports. The bolt material has a failure shear stress of 175 mPa.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680 MPa, and for the bronze (σY)br=490 MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa.
The five-bolt connection shown must support an applied load of P = 214 kN. If the average shear stress in the bolts must be limited to 249 MPa, determine the minimum bolt diameter that may be used in the connection.
A tensile stress is to be applied along the long axis of a cylindrical copper rod that has a diameter of 2.1 mm. Determine the magnitude of the load required to produce a 0.002 mm change in diameter if the deformation is entirely elastic. Answer in N. The modulus of elasticity of copper is 110 GPa and it's Poisson's Ratio is 0.34. Round your answer to 0 decimal places.
A large water tank that has a capacity to carry 20,000 liters is to be supported by four cylindrical posts. These four support posts are made of plain carbon (1045) steels with the yield and tensile strengths of 310 MPa and 565 MPa, respectively. Determine the minimum required diameter of the post assuming a factor of safety of 5.
The pipe assembly shown is subjected to a force F = 7 kN and P = 14 kN. It is made of steel with Sy = 250 MPa. Determine the safety factor at point H using the maximum shear stress theory. Select one: a. NH = 6.427 b. NH = 3.570 c. NH = 5.355 d. NH = 4.590