The bar shown in the figure has a square cress section for which the depth and thickness are 40 mm. If an axial force of 800 N is applied along the centroidal axis of the bar's cross- sectional area, determine the average normal stress and average shear stress acting on the material along (a) section plane a-a (b) section plane b-b.

The bar shown in the figure has a square cress section for which the depth and thickness are 40 mm. If an axial force of 800 N is applied along the centroidal axis of the bar's cross- sectional area, determine the average normal stress and average shear stress acting on the material along (a) section plane a-a (b) section plane b-b.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.12P: Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft....

See similar textbooks

Similar questions

EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
A 9 ft wide and infinitely long flexible strip load of 800 lb/ft2 is placed on an elastic medium as shown in Figure P8.7. Find the vertical stress increase at points A, B, and C located 3 ft below the surface.
Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43
The bar shown in the figure has a square cress section for which the depth and thickness are 40 mm. If an axial force of 800 n is applied along the centroidalaxis of the bar’s crosssectional area, determine the average normal stress and average shear stress acting on the material along (a) section plane a-a (b) section plane b-b.)
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
Plane AB is under pressure and Plane AB has an angle = 30 degrees to sigma = 50 nPa.a. Determine the equations used to calculate the normal and shear stress in the plane ABb. Draw a normal vector sketch on the plane AB and the angle formed between the normal vector andc. Calculate normal stress and shear stress in plane AB (Round up to 4 digits after comma)d. Plot the point normal stress and shear stress plane AB on the Mohr Diagram sketch.
Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the ring at B, determine the angle ? so that the average normal stress in each rod is equivalent. What is this stress? (10)
A very thin rectangular plate (see figure (a)) is subjected to a biaxial plane stress state (σx, σy). The width and height of the plate are b = 7.5 [in] and h = 2.5 [in], respectively. The measures show that the strains in the (x, y) directions are εxx = 2.85x10−4 and εyy = −1.90x10−4, respectively. Figure (b) shows a 2D front view of the plate. a) Draw and identify the principal stresses and the maximum shear stress on Mohr's circle. In what orientation does this maximum shear occur? b) Calculate the unit volume change e = εxx + ?εyy + εzz Note: remember that in a plane stress state we have σz = τxz = τyz = 0 and if it is also bi-axialwe have τyx = 0.
Determine the stress components (σx′ , τx′y′) acting on the inclined plane AB in (Figure 1), where τxy=−38.5MPa. Solve the problem using the method of equilibrium.
A moment is exerted on the profile given in the figure to make an angle B with the vertical. Calculate the stress at point B. Given a = 90 mm, b = 60 mm, c = 110 mm, d = 130 mm, Beta = 80 degrees, M = 13 kNm,
Show complete solution, include necessary figures. The major and minor principal stresses acting at a point are 80 psi compression and 20 psi tension.A. Draw the Mohr's circle for this stress combination.B. What is the maximum shear stress acting at the point and what value of normal stress acts on the plane?C. Determine the value of the normal and shear stress acting on a plane that is 30 degrees from the minor principal plane.
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 23.6 ksi, Sy = 2.8 ksi, and Sxy = 7 ksi. Assume β=19∘. Determine the normal stresses σx and σy and the shear stress τxy at the point.