(a) please from question in photo 1. The diagram below shows a typical data acquisition system where an analoguesignal from a transducer is converted to a digital form suitable for subsequentdigital signal processing.ElectricalPhysicalvariablesignal(analogue)DigitaloutputS/HADCTransducerSample-and-HoldThe block labeled ADC contains an 8-bit successive-approximationanalogue-to-digital converter.(a)(i)With the aid of suitable diagrams describe the operation of thisdevice.(ii)The ADC is designed to operate over an input voltage range of0 to 5V. Determine the resolution of the ADC.

Answered: Image /qna-images/answer/3b303171-117a-41bc-a1ce-b4c2376cd1c3.jpg

The block labeled ADC contains an 8-bit successive-approximation analogue-to-digital converter. (i) With the aid of suitable diagrams describe the operation of this device. The ADC is designed to operate over an input voltage range of 0 to 5V. Determine the resolution of the ADC. (ii)

The block labeled ADC contains an 8-bit successive-approximation analogue-to-digital converter. (i) With the aid of suitable diagrams describe the operation of this device. The ADC is designed to operate over an input voltage range of 0 to 5V. Determine the resolution of the ADC. (ii)

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Consider a special purpose decoder that is called BCD to seven-segment decoder. The decoder takes a 4-bit Binary Coded Decimal (BCD) number X3 X2 X4 X0 (0-9) and produces 7 outputs a, b, c, d, e, f, and g The specification of this circuit is as follows: ⚫ The 7 outputs of the decoder are connected to LED segments as shown in the figure below. The LEDs are active low, ie, the LED emits light when it is connected to logic 0. • The decoder output is determined in a way so that the LED segments display the decimal representation of the input. For example, if the input X3 X2 X1 X0 is 0001 respectively (which is equivalent to decimal 1), the outputs a, b, c, d, e, f, and gare 1001111 showing the letter 1 on the display (remember the LEDs are active low). Decoder W- 4x7 e U Answer the following questions: a. Fill in the truth table of that decoder. Choose a good value for the output when the input is greater than decimal 9. b. Derive the simplified Boolean expressions for the outputs a, b, c,…
17. An analog signal carries 4 bits in each signal unit. If 1000 signal units are sent per second, then baud rate and bit rate of the signal are ________ and ____________ a. 4000 bauds \ sec & 1000 bps b. 2000 bauds \ sec & 1000 bps c. 1000 bauds \ sec & 500 bps d. 1000 bauds \ sec & 4000 bps
157. The term that refers to the phase continues through the boundary of two signal elements is a. non coherent BFSK b. coherent BFSK c. Binary ASK d. Multilevel ASK
Explain the block diagram of computerized 12 lead ECG. Also draw theanalog Front End with RLD and Optical Signal Isolator.
(a) The message input of the Pulse Code Modulation (PCM) is given as follows: Am (t) = cos (20πt) (i) Suggest the minimum sampling frequency and justify why this value issuggested. Support your justification by illustrating its frequency spectrum withcomplete labels. (ii) If the message signal in quantized uniformly to 16,383 levels, calculate thenumber of bits required to encode the samples (iii)Evaluate the significant performance of the PCM if the quantization level isreduced to 4 levels (iv)With the same quantization level in (c), suggest the compression characteristicthat will handle the given input signal voltage between -1 V to 1 V if themessage signal use μ-law companding to provide non-uniform quantization.Given μ=200. Support your answer with relevant complete illustration.
please slove this question it's from telecommunication engineering. We use the DFT to compute the amplitude spectrum of a sampled data sequence with a sampling rate fs =3,000Hz. It requires the frequency resolution to be less than 0.5 Hz. determine the number of data points used by the FFT algorithm and actual frequency resolution in Hz, assuming that the data samples are available for selecting the number of data points.
The basic principle of differential coding techniques like Differentil PCM (DPCM) and Adaptive Differential PCM (ADPCM) is to transmit information _____. A. about the changes in sample value B. approximation to the input signal C. using artificial signal D. of the actual sample values themselves
Computer Science Question (1)A discrete-time signal x[n] is defined as: x[n] = [-3 1 2 3 0 -1 -2 3]Write a MATLAB code to plot the following signals: -a) x[−2n + 2].b) x[n-1] u[2 − n].c) x[n-2] r[ n].Question (2)plot the convolution of:x[n] = [1 4 3]h[n] = [1 2 3] without using conv function in MATLAB
Consider a convolutional code with k = 1, n = 3 and L = 3. The encoder generators aregiven by 91 = [110], 92 = [001] and 93 = [011].Assume the Viterbi algorithm is used for decoding at the receiver and considerthe received bit sequence at the input of the channel decoder being [10 0100110011].Answer the following questions.(a) What is the decoded information bit sequence? (b) What is the value of the cumulative metric (i.e., Hamming distance) of thefinal survivor path of the decoding process?(c) Draw the final survivor path of the trellis for the decoding process.Instruction for Part (c): An example of drawing a path in the trellis is shown below.
Assume a digitization of a unipolar signal that can change between 0 to 9V volts into 4 bit digital equivalent. Calculate the resolution and the number of quantized levels. Show the graph of the ADC. Show your complete solution.
Please written by computer source Question 1 a. Tri-state logic is often used in digital design to resolve the conflict that arises when more than one output is connected. With the aid of a diagram, explain how this can be used in a digital design to share a single bus. b. Examine the following VHDL statements and draw a synthesised schematic for the corresponding design. c. Using concurrent statements only, (no process), describe a decoder in VHDL which satisfies the following conditions, and draw the High level RTL schematic for this design. 3 inputs (A, B, C) and 1 output (Z). The output is equal to 1 when either input A is equal to 1 or only input C is equal to 1. All signals are of type 'std_logic d. VHDL allows the designer to describe hardware using different language constructs. Although, these constructs might have the same, or similar, functionality, the result of the synthesis is quite different. One example is the if-else and the case constructs. Explain the difference…
ADC 0804 is an 8 bit ADC which operates on successive approximation principal. Its majorcharacteristics include single 5V power supply and 0-5V analog input range. After the conversion adigital output code 00000000 is found or 0V and 11111111 is found for 4.9805V. What will be thecorresponding digital output for 4.140625V?