onsider a special purpose decoder that is called BCD to seven-segment decoder. The decoder takes a 4-bit Binary Coded Decimal (BCD) number X3 X2 X4 X0 (0-9) and produces 7 outputs a, b, c, d, e, f, and g The specification of this circuit is as follows: ⚫ The 7 outputs of the decoder are connected to LED segments as shown in the figure below. The LEDs are active low, ie, the LED emits light when it is connected to logic 0. • The decoder output is determined in a way so that the LED segments display the decimal representation of the input. For example, if the input X3 X2 X1 X0 is 0001 respectively (which is equivalent to decimal 1), the outputs a, b, c, d, e, f, and gare 1001111 showing the letter 1 on the display (remember the LEDs are active low). Decoder W- 4x7 e U Answer the following questions: a. Fill in the truth table of that decoder. Choose a good value for the output when the input is greater than decimal 9. b. Derive the simplified Boolean expressions for the outputs a, b, c, d, e, t and g using K-maps. Decimal Corresponding Digit LED segments Input X2 0 X2 Xo Output def & X3 0 0 0 abc 0 0 0 0 0 1 0 2 14 1 1 1 1 1 15

onsider a special purpose decoder that is called BCD to seven-segment decoder. The decoder takes a 4-bit Binary Coded Decimal (BCD) number X3 X2 X4 X0 (0-9) and produces 7 outputs a, b, c, d, e, f, and g The specification of this circuit is as follows: ⚫ The 7 outputs of the decoder are connected to LED segments as shown in the figure below. The LEDs are active low, ie, the LED emits light when it is connected to logic 0. • The decoder output is determined in a way so that the LED segments display the decimal representation of the input. For example, if the input X3 X2 X1 X0 is 0001 respectively (which is equivalent to decimal 1), the outputs a, b, c, d, e, f, and gare 1001111 showing the letter 1 on the display (remember the LEDs are active low). Decoder W- 4x7 e U Answer the following questions: a. Fill in the truth table of that decoder. Choose a good value for the output when the input is greater than decimal 9. b. Derive the simplified Boolean expressions for the outputs a, b, c, d, e, t and g using K-maps. Decimal Corresponding Digit LED segments Input X2 0 X2 Xo Output def & X3 0 0 0 abc 0 0 0 0 0 1 0 2 14 1 1 1 1 1 15

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 9VE

See similar textbooks

Similar questions

Draw a 4-input adder for single-bit values: that is, a set of logic gates with 4 input wires each representing a number between 0 and 1 and a multi-bit output z, composed of wires z0 through z... (where z0 is the low-order bit, z1 the next, etc., up to the number of wires needed for this task). The gates should ensure that z = the sum of all four inputs.
A circuit has four inputs p,q,r,s representing the natural binary number 0000=0,to 1111=15 p is the most significant bit .the circuit has one output, x,which is true if the input to the circuit represent is a prime number and false other wise (A) design a true table for this circuit, and hence obtain an expression for x in terms of P,Q,R,S.
Use VHDL to implement a 16-to-1 Multiplexer. The inputs are w0, w1, w2, w3, w4, w5, w6, w7, w8, w9, w10, and w11. The last four inputs are not attached to an input signal. How many select bits need the circuit?
Computer Science if a 12-bit linear pcm code with a resolution of 0.188V, if the voltage range that would be converted to the pcm code: 111110111101 is in the form X volts to Y volts where X and Y are constants. Find X+Y
An 8 x 1 multiplexer has inputs A , B , and C connected to the selection inputs S2 , S1 , andS0 , respectively. The data inputs I0 through I7 are as follows:(a) I1 I2 I7 0; I3 I5 1; I0 I4 D ; and I6 D ’.(b) I1 I2 0; I3 I7 1; I4 I5 D ; and I0 I6 D ’.Determine the Boolean function that the multiplexer implements.
. Implement a circuit for the following problem using Logisim. The input to the circuit are 3 4-bit numbers, A,B,C. The sum of A and B is subtracted from C. The difference (result of subtraction) is compared with A. The circuit has 3 outputs lines depending on comparison. Use appropriate chips in Logisim for the operations mentioned Answer step by step
Design a circuit using a Multiplexer, (((USING A MULTIPLEXER NOT A DECODER))) that has two inputs X, and S, where X represents an 8-bit BCD number,S is a sign bit. The circuit has one output Y, which is the Binary representation of thesigned-magnitude BCD number. A negative output is represented in the Binary 2’scomplement form.
Using Verilog continuous assignments or VHDL signal assignments, write a description of the circuit specified by the following Boolean functions: Out_1=(A+B′)C′(C+D)Out_2=(C′D+BCD+CD′)(A′+B)Out_2= (AB+C)D+B′CWrite a testbench and simulate the circuit’s behavior.
The circuit of Exp #8.2, configured as a subtractor, can be used to compare two 4-bit numbers. Subtractor outputs Cout and (S3.so) can be combined logically to indicate the relationship between inputs A and B. The gate circuit needed to do this appears as the interface block in the following diagram. Subtractor 220 ohm Cout A - B LEDO 4 A S3 A < B LED1 220 ohm Interface Block S2 (Your Design) 220 ohm B S1 A > B LED2 So (A - B) AirSupplyLab.com Figure 8.2: 4-bit Comparator Design the contents of this interface. You will build the circuit using only 2 chips: 1. a 7402 NOR chip 2. either a 7432 OR chip or a 7408 AND chip. Design the interface two ways: (a) an OR and NOR circuit, and (b), a NOR and AND circuit. Include both designs in your lab notebook and build and test one of them. Each design consists of 3 parts – one for each output – and requires 5 gates total. ExpressSCH has custom DM symbols for all gates (including ANDS and ORs). Use them, but only where they make circuit…
Build a circuit that takes four bits as input: W, X, Y, Z. Treat WX as a 2-bit unsigned binary number, and treat YZ as a second 2-bit unsigned binary number. Your circuit should generate the output corresponding to the product of WX and YZ. You will need 4 bits of output for this problem.For example, if your input was 1011, your inputs correspond to 2 and 3. That product is 6, so your output will be 0110.Create a truth table for this problem, show all k-maps and minimizations, and build the corresponding (minimized) circuit. Use XOR, XNOR, NAND, and NOR as appropriate if it reduces the number of gates used.
We want to design a circuit that counts the number of 1s present on 3 binary inputs a, b, c and outputs that number in binary using 2 outputs y and z. For example an input of a=1, b=1, c=0 has two ones, so the output would be 210 = 102 i.e., y=1, z=0. a) Express y and z as sum of min‐terms of variables a, b and cb) Simplify the expressions for y and z using K maps.c) Draw the logical circuits for y and z using gates.
Implement a combinational circuit with three inputs x, y, and z and three outputs A, B, and C.When the binary input is equal to 0, 1, 2 or 3, then the output is equal to the input + 1.When the binary input is 4, 5, 6 or 7 then the binary output is equal to the input – 2.