The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the O.63-in .-diameter pin at A, and the 0.3-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5012 Ib. Round off the final answer to two decimal places. 0007 P.png ... 70 4 in 3.5 in. 30° 0.5-in dia. Detail at A

The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the O.63-in .-diameter pin at A, and the 0.3-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5012 Ib. Round off the final answer to two decimal places. 0007 P.png ... 70 4 in 3.5 in. 30° 0.5-in dia. Detail at A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Link BD consists of a single wooden member 38 mm wide and 19.2 mm thick. Knowing that each pin has a 14.3-mm diameter, determine the maximum value of the average normal stress (in MPa) in link BD if θ= 0° and P = 26.7. Round off the final answer to three decimal places.
For the riveted connection shown, the allowable shearing stress in the 25mm rivets is 140MPa. Assume the plates are adequate to transmit the load to the rivets. P = 60 kN.a. Determine the shearing stress in the most stressed rivet.b. Determine the maximum allowable value of P.c. If P = 80 kN, determine the minimum diameter of rivets.
A flange coupling connects two 2 inch diameter shaft. The flanges are fitted by 6 bolts on a 7 “ bolt circle. If the shaft rotates at 300 rpm and transmit 45 hp, determine the required bolt diameter when allowable shear stress of 11,000 psi.
Part of a steel tube, 30mm external diameter and 6mm thick, is to be enlarged to form a compound tube of external diameter 40mm. Determine: The metal thickness of the enlarged section if the maximum shear stress is to be the same in both sections, when the compound tube is subjected to a torque
Straight rods of 0.30-in. diameter and 200-ft length are sometimes used to clear underground conduits of obstructions or to thread wires through a new conduit. The rods are made of high-strength steel and, for storage and transportation, are wrapped on spools of 5-ft diameter. Assuming that the yield strength is not exceeded, determine (a) the maximum stress in a rod, when the rod, which was initially straight, is wrapped on the spool, (b) the corresponding bending moment in the rod. Use E= 29 * 106 psi.
Link BD consists of a single wooden member 38.2 mm wide and 20.4 mm thick. Knowing that each pin has a 13.3-mm diameter, determine the maximum value of the average normal stress (in MPa) in link BD if θ= 0° and P = 30.4. Round off the final aswer to three decimal places.
For the connection shown, the average shear stress in the 16-mm-diameter bolts must be limited to 270 MPa. Determine the maximum load P that may be applied to the connection.
A chain block is hanged on a pin which is supported by plates on both side as shown. If the maximum safe load capacity is 3000 lb, determine (a) the shearing stress on the shaft having a diameter of 1.75 in. (b) and the thickness of the plates if the bearing stress on the plates is 20% greater than the shearing stress.
A rectangular column is made of a grade of sawn wood that has an adjusted allowable stress for compression parallel to the grain σC = 8.3 MPa and a modulus of elasticity E = 11.1 GPa. Using the allowable-stress method, determine the largest allowable effective length L that can be used. Take P = 88 kN. (Round the final answer to two decimal places.) The largest allowable effective length L that can be used is m.
Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 40 kN if it developed a stress of 35 MPa. Take note that the inner diameter is 3/6 of the outer diameter.
Two wooden planks, each 7/8 in thick and 6in wide, are joined by the glued mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 120psi, determine the smallest allowable length d of the cuts if the joint is to withstand an axial load of magnitude P=1200-lb. Note: Seven surfaces carry the load, P=1200-lb
The lap joint shown is connected by 6 pieces rivets. Assuming that the load P = 70 KN is carried equally by the six rivets.Determine the diameter of the rivets if the allowable shear stress is 148.54 MPa.