A short shoe external drum brake is shown in the figure. The diameter of the brake drum is 500mm. The dimensions a = 1000 mm, b = 500 mm and c = 200 mm. The coefficient of frictionbetween the drum and the shoe is 0.35. The force applied on the lever F = 100 N as shown inthe figure. The drum is rotating anti-clockwise. The braking torque on the drum isN.m(round off to two decimal places).aBrakeshoeb

Given data; External drum brake is shown in figure. Diameter,d= 500 mm Dimensions of the brake…

Answered: The braking torque on the drum is

Engineering

Mechanical Engineering

The braking torque on the drum is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The width of the simple band brake shown in the figure is 30 mm. The coefficient of friction between the brake and the drum surface is 0.20. Determine the braking torque and thickness of the band if the tensile stress is not to exceed 65 N/mm2.
A differential band brake is shown in the figure. The diameter of the drum is 800 mm. The coefficient of friction between the band and the drum is 0.3 and the angle of embrace is 240°. When a force of 777 N is applied at the free end of the lever, find: a. The maximum force, in Newtons, in the band for the clockwise rotation of the drum b. The minimum force, in Newtons, in the band for the clockwise rotation of the drum c. The maximum force, in Newtons, in the band for the counter clockwise rotation of the drum d. The minimum force, in Newtons, in the band for the counter clockwise rotation of the drum e. The torque which can be applied by the brake, in N-m, for the clockwise rotation of the drum.
The block brake, as shown in the figure, provides a braking torque of 376 N-m. The diameter of the brake drum is 258 mm. The coefficient of friction is 0.3. Find: a. The force (P), in Newtons, to be applied at the end of the lever for the clockwise rotation of the brake drum b. The force (P), in Newtons, to be applied at the end of the lever for the counter clockwise rotation of the brake drum; and c. The location of the pivot or fulcrum, in mm, to make the brake self-locking for the clockwise rotation of the brake drum.
A single block brake is shown in the figure. The diameter of the drum is 250 mm and the angle of contact is 103.7°. If the operating force of 661N is applied at the end of a lever and the coefficient of friction between the drum and the lining is 0.35, determine: a. The tangential braking force, Ft, in Newtons b. The braking the torque transmitted by the block brake in N-m.
The figure shows an internal rim-type brake having an inside rim diameter of 11in and a dimension R of 3.5 in. The shoes have a face width of 1.25 in. Find the braking torque and the maximum pressure for each shoe if the actuating force is 205 Ibf, the drum rotation is counterclockwise, and f=0.32. The maximum pressure on the right-hand shoe parp is [ 16.99] @ psi. The maximum pressure on the left-hand shoe pa| H is [100.813 | @ psi. The torque on the right-hand shoe Tgis [ .056 | @ kipin. The torque on the left-hand shoe T is [ .332| @ kipin. Total braking torque Tiotal s [-3887] @ Kip-in.
For the drum brake shown in the following figure, there is an inner rim diameter of 280 mm and dimension a = 90 mm. The shoes have a face width of 30 mm. The force exerted by the cylinder hydraulic is 1000 N and the average coefficient of friction is 0.3. Determine: a) The maximum pressure in each shoe; b) The braking torque; c) Reactions resulting from the pivot pin;
In a pulley brake with inside shoes with an inner rim diameter of 300 mm given in the figure,R= 150 mm, shoe width 37.5 mm. The value of the force F applied on the shoes isIt is 2 kN. If the average friction coefficient is taken as 0.28;a) Max. what is the value of the pressure?b) Find the braking and normal torques and the total torque at each shoe.c) What are the values of the reaction forces on the right shoe knuckle pin?Note: Max. Take the angle (theta) at which the pressure “pa” occurs as 90 degrees.
In the design in the figure, a force of Fn=45992 N acts in the vertical plane on a machine element with a diameter of D=200 mm on the shaft resting on the A and B bearings. If the angle made by this force with the horizontal is b=40o, find the life of the 6210 coded Deep Ball bearing to be used in the B bearing, in hours. Number of revolutions = 30 rpm. 1-) The diameter of the machine element on which the force acts will be taken into account in the calculation of bearing forces (That is, it will be assumed that the Fn force AFFECTS THE GROUND shown in the figure, NOT the axis of the shaft). 2-) Pi number will be taken as 3.14.
Symmetrical shoes will not create moment around the joint The position of the pads with an angle of 90° on the brake where it is placed in the figure is shown in the figure. The brake mechanism is fixed to the ground by the support plate. The disc in the figure rotates clockwise and the friction coefficient of the pads is accepted as 0.491. If a force of 565 N is applied on the arm from the point shown on the figure;a) What is the dimension e shown in the figure so that the shoe does not create a moment around the joint?how much should it be? Calculate.b) Draw free body diagrams of ABC opening lever and both lining levers.c) What is the normal force acting on each pad? How much braking torqueoccurs? calculate
3 - The wheel of a car with a mass of 3000 kg has a diameter of 1.6 m and the coefficient of friction with the road surface is given as μ = 1.80. Assume that the weight of the car is evenly distributed on all four wheels. Calculate the maximum torque that the engine can create on one of the tractor wheels without spinning the wheel. Assume that the car is stationary. a) 17560 N·m B) 12644 N·m NS) 10584 N·m D) 14670 N·m TO) 9768 N·m
The two wedges are stacked as shown in figure 1. a.) What is the total reaction at the wall if the coefficient of friction between AB is 0.1 b.) The coefficient of friction between AC and BD is 0.2. c.) How many contact surfaces in the Figure? d.) What is the angle of friction at AC in the figure?
1. A double square thread power screw has a pitch of 6 mm and mean radius of34 mm. If it is used to lift a load 50 kN and coefficient of friction of threads is 0.15, determine the torque required toturn the screw.A. 343.74 N-m B. 353.47 N-m C. 335.47 N-m D. 347.35 N-m2. A lubricated bolt needs an initial torque of 145 lb-ft to take the initial tension brought by the compressor withoutbreaking. Determine the initial torque needed by the bolt if the bolt was not lubricated.A. 107.85 lb-ft B.108.25 lb-ft C. 108.75 lb-ft D. 193.33 lb-ft