The Cuk converter has parameters V, = 12 V, D = 0.6, L, = 200 µ.H, L = 100 µH, C, = C,= 2 µF, and R = 12 N, and the switching frequency is 250 kHz. Determine (a) the output voltage, (b) the average and the peak-to-peak variation of the currents in L, and L, and (c) the peak-to-peak variation in the capacitor voltages. %3D %3D %3D

The Cuk converter has parameters V, = 12 V, D = 0.6, L, = 200 µ.H, L = 100 µH, C, = C,= 2 µF, and R = 12 N, and the switching frequency is 250 kHz. Determine (a) the output voltage, (b) the average and the peak-to-peak variation of the currents in L, and L, and (c) the peak-to-peak variation in the capacitor voltages. %3D %3D %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A) Design a buck-boost converter with the specifications: Vin = 28 V, in the range [24V,32V], Vout=12 V (with opposite polarity to Vin), load power in the range [0, 120 W], such that to operate in CCM for any line and load value. Select a switching frequency of 100kHz. Choose C= 1.8mF, 25V, 2.5mΩ
The following specifications are given for the dual input, balanced- output differential amplifier: RC = 2.2 kΩ, RE = 4.7 kΩ, Rin 1 = Rin 2 = 50Ω, +VCC= 10V, -VEE = -10 V, βdc =100 and VBE = 0.715V. assume ICQ = 0.988 mA a. Determine the voltage gain. b. Determine the input resistance c. Determine the output resistance.
The common-mode gain of the front-end circuit for the instrumentation amplifier is equal to ACM= 1 V/V. If the instrumentation amplifier is not reducing the common-mode signal, then why is the CMRR of an instrumentation amplifier higher than a differential amplifier, in general?
In the circuit given in the figure, Vcc = 30V, R1 = 150K ohm, R2 = 47K ohm, RL = 20K ohm and transistor parameters are given as VBE = 0.6 V, beta (dc) = beta (0) = 300. The hybrid model of the transistor will be used.a) It is given as I (CQ) = 2mA and V (CEQ) = 10V at the operating point. Since the input impedance of the circuit must be Zi = 20K ohms, calculate the resistance values of R (E1), R (E2) and R (C).b) Derive the voltage gain expression A (vi) and calculate its value. I sent you question's image. Thank you..
A resistive load of 4 ohms is matched to the collector impedance of an amplifier by means of a transformer having a turn ratio of 40:1. The amplifier uses a DC supply voltage of 12V in the absence of input signal. When signal is present at the base, the collector voltage swings between 22V and 2V, while the collector current swings between 0.9A and 0.05A. Determine: (a) the collector impedance (b) Signal power output (c) DC power input (d) Collector efficiency
Design For the design of the amplifiers, consider a very large load resistance RL. Use a 15 V DC source and a sinusoidal input signal of 200 mVpp and 1 kHz. Design a voltage amplification stage with a common emitter amplifier thatmeet the following specifications: Voltage gain of 15 (Av2 ≅ 15) Input impedance greater than or equal to 10 times Zo1 (Zi2 ≥ 10 Zo1). Low cut frequency less than or equal to 20 Hz (fcb2 ≤ 20 Hz). Maximum symmetric excursion. Use a 2N2222A (NTE123A) transistor. Also, determine the value of the impedance output (Zo2) of the designed circuit.
For the follower circuit in the figure below, consider k = 0.3x10-3 , rd = 100kOhm, VT = VGS(TH) = 3V and : (a) Draw the small-signal model considering the pi model (b) Determine the INPUT impedance (c) Determine the OUTPUT impedance (d) Determine the voltage gain (Av)
Values of Vg = 125 V, V0 = 75 V, f = 15 kHz, R = 10  are given for the buck converter.The switch, diode, coil and capacitor used are considered ideal. According to this:a) In order that the peak-to-peak value of the coil current ripple does not exceed 5% of the rated load current valuethe inductance (L) of the coil to be used and the average output voltage of the output voltage ripple.Calculate the capacity (C) of the capacitor that should be used to be 1% of the value. b) This circuit must be used for continuous transmission (CCM) operation at 50% load.Find the minimum inductance value.
1. For the circuits shown below, if A=∞, Calculate a) The overall input resistance, Rin b) The output resistance, Rout c) Overall voltage gain (vo/vs)
In a DC-DC boost converter, the duty ratio is controlled to regulate the output voltage at 48 V. The input DC voltage is 24 V. The output power is 120 W. The switching frequency is 50 kHz. Assume ideal components and a very large output filter capacitor. The converter operates at the boundary between continuous and discontinuous conduction modes. The value of the boost inductor (in μH) is
Calculate the output impedance for small-signal equivalent circuit. (R1=10 k ohm, r0, =10 k ohm)
Given r_e = 10 Ω, β = 200, A_v = -160, and A_i = 19 for the collector-feedback network shown below, determine a) R_C; b) R_F; and, c) V_CC .