The collar shown slides frictionlessly along the rod and is released from rest when q 60. Each wheel has a radius of 0.8 ft and a radius of gyration of 0.5 ft, and they roll without slipping. The collar just touches the spring when the two rods are horizontal. Find a. the velocity of the collar is it just reaches the spring, and b. the maximum depression of the spring. m =1 slug 1 ft m = 0.5 slug 1 ft m = 2 slugs m = 0.5 slug m = 2 slugs k= 100 lb/in

The collar shown slides frictionlessly along the rod and is released from rest when q 60. Each wheel has a radius of 0.8 ft and a radius of gyration of 0.5 ft, and they roll without slipping. The collar just touches the spring when the two rods are horizontal. Find a. the velocity of the collar is it just reaches the spring, and b. the maximum depression of the spring. m =1 slug 1 ft m = 0.5 slug 1 ft m = 2 slugs m = 0.5 slug m = 2 slugs k= 100 lb/in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A smooth can C, having a mass of 5 kg, is lifted from a feed at A to a ramp at B by a rotating rod. The rod maintains a constant angular velocity of θ˙ = 0.5 rad/s, Neglect the effects of friction in the calculation and the size of the can so that r=(1.2cos⁡θ)m. The ramp from A to B is circular, having a radius of 600 mm. (a) Determine the magnitude of the force which the rod exerts on the can at the instant θθ = 30∘∘. Express your answer to three significant figures and include the appropriate units.
She releases her m= 4.6-kg, 220-mm diameter bowling ball with an initial velocity vG of 5 m/s and initial backspin of ω= 8 rad/s. The coefficient of kinetic friction between the ball and the bowling lane is μk= 0.12. The ball will start rolling without sliding after impact. Which of the following best approximates the time t it takes for the bowling ball to stop slipping?a. 2.28 sb. 2.68 sc. 1.427 sd. 1.989 s
Q5: Determine the speed of slider at position 2 when slider weight 0.75 kg and P=300 N. The slider starts from rest at position land the unstretched length of the spring of modulus is k=210 N/m is 200 mm. Neglect frictions. 200 mm 200 P 250 mm mm 250 mm 15
The system is released from rest in the position shown.Cylinder B falls through the hole in the bracket, but ring C (shown in section) separates from the cylinder when it hits the bracket.The coefficient of kinetic friction between block A and the inclined ramp is μk = 0.2, and the mass of the pulley is negligible.(a) Determine the speed of block A at the moment ring C strikes the support. Express the answer in m/s. Consider the following values:mA = 48kgmB = 12kgmC = 15kgθ = 31°h = 1.2m
A hammer head H having a weight of 0.26 lb is moving downwards at 40 ft/s when it strikes the head of a nail of negligible mass and drives it into a block of wood as shown. Find the impulse on the nail if it is assumed that the grip at A is loose, the handle has a negligible mass, and the hammer stays in contact with the nail while it comes to rest. [Show work fast , Don't copy]
Two identical 16-kg spheres are attached to the light rigid rod, which rotates in the horizontal plane centered at pin Part A: If the spheres are subjected to tangential forces of P = 10 N, and the rod is subjected to a couple moment M=(8t)N⋅mM=(8t)N⋅m, where t is in seconds, determine the speed of the spheres at the instant t = 4 s. The system starts from rest. Neglect the size of the spheres. Express your answer to three significant figures and include the appropriate units.
The two disks AA and BB have a mass of 4 kgkg and 6 kgkg , respectively. They collide with the initial velocities shown. The coefficient of restitution is eee = 0.75. Suppose that (vA)1(vA)1va = 6 m/sm/s , (vB)1(vB)1vb = 8 m/sm/s Determine the magnitude of the velocity of BB just after impact. Determine the angle between the xx axis and the velocity of BB just after impact, measured clockwise from the positive xx axis.
The plank AB has a mass of 7 kg. The rollers D and E are each of mass 5kg and are 0.5 m in diameter. The plank is released from rest with roller D under the end A and the roller E, under the mass center C. assuming no slipping, determine the velocity of the plank when roller E is under end B.
The door is made in one piece, the ends of which move along the horizontal guides and vertical. If the door is in the open position, θ = 0◦ , and then released, determine the speed (this is already solved Vinpact = 31.9 ft / s) at the that its outer A hits the stop C. Suppose the door is a 180-lb thin plate that has a width of 10 ft. Determine the impulsive force with which point A hits point C in an instant of 5 thousandths of a second.
DYNAMICS OF RIGID BODIES UPVOTE WILL BE GIVEN.PLEASE WRITE THE COMPLETE SOLUTIONS CORRECTLY AND LEGIBLY. NO LONG EXPLANATION NEEDED. BOX THE FINAL ANSWER. Two blocks A and B of the same mass 1.69 kg are released from rest on a 23° incline when they are S = 12.8 m apart, as shown. The coefficient of friction under the upper block A is 0.2, and that under the lower block B is 0.35. Compute the elapsed time (in seconds) until the blocks touch each other. Round off only on the final answer expressed in 3 decimal places.
(a) Two blocks are joined by an inextensible cable as shown in Figure. If the system is released from rest, determine the velocity of block A after it has moved 2 m by using the data given. Assume that the coefficient of kinetic friction between block A and the plane is ?k = 0.25 and that the pulley is weightless and frictionless.
A ball of mass (m) is connected by a light string of length (L) to a frictionless pivot point P and swings as a pendulum as shown in Fig. (1). The ball is released from rest at point A when the string makes an angle of e with vertical. Determine; 1) The velocity of the ball as it passes through point B. 2) The tension TA in the string at A. 3) The tension Te in the string at B.