The components of stress tensor are given as follows: 0= 25kPa oy= 50kPa and txy-70kPa. a. Determine the magnitude and directions, of major and minor principal stresses. b. Determine the magnitude and directions of the maximum shear stress. c. Determine the normal and shear stresses acting on a soil element inclined 30* from the horizontal plane. Give both analytical and graphical solution.

The components of stress tensor are given as follows: 0= 25kPa oy= 50kPa and txy-70kPa. a. Determine the magnitude and directions, of major and minor principal stresses. b. Determine the magnitude and directions of the maximum shear stress. c. Determine the normal and shear stresses acting on a soil element inclined 30* from the horizontal plane. Give both analytical and graphical solution.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.2P

See similar textbooks

Similar questions

EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
Using the principles of Mohr’s circles for the soil element shown in Figure 10.36, determine the following:a. Maximum and minimum principal stressesb. Normal and shear stresses on plane AB
A soil element is shown in Figure 10.38. Using the pole meathod, determine: a. Maximum and minimum principle stresses. b. Normal and shear stresses on plane AB Solve this problem three ways: first via equations, second via Mohr’s circle and the two-theta method, and third via Mohr’s circle and the origin of planes. All methods should give the same answer.
A Soil Element is shown in figure . Determine the Following: a. Maximum and Minimum Principal Stress b. Normal and Shear stresses on plane AB
For the stress soil element shown, determine the following using the Pole Method. A. The major principal stress B.The minor principal stress C. Normal stress on plane AE D. Shear stress on plane AE
Using the principles of Mohr circle, for the soil elements shown, determine the following. a.)Maximum principal stress b.) Minimum principal stress c.) Normal Stress on plane AB d.) Tangential stress on plane AB
A soil element is shown in Figure 2.32. Determine the following using Pole Method.a. Maximum and minimum principal stressesb. Normal and shear stresses on plane AB
Define and Explain Normal and Shear stress acting on plane and also its determination by plotting Mohr Circle.
Find the vertical stress increment at this point of interest using Boussinesq analysis.
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft.
3. The following convergence measurements (U) have been made in a 4.6-m-diameter circular vertical shaft in good quality granitic rock mass (Em = 40 GPa, ν = 0.2): θ (deg) U (mm) 0 2.25 45 2.39 90 1.50 135 1.00 a) Derive the equations that relate convergence to in situ stress. b) The angle θ is measured (clockwise) with respect to the x-axis, which is oriented 30 degrees clockwise from True North. What is the orientation of the maximum principal stress with respect to True North?
Refer to Figure 10.46. A flexible circular area of radius 6 m is uniformly loaded. Given: q = 565 kN/m2. Using Newmarks chart, determine the increase in vertical stress, z, at point A. Figure 10.46