The compound bar containing steel bronze and aluminum segments carries the axial loads shown in the figure. The properties of the segments are listed in the table. Determine the maximum allowable value of P in pounds if the change in length of the entire bar is limited to +0.07in. A (in2) E (psi) L (FT) Steel 0.75 300000002 Bronze 1 120000004 Aluminm 0.5 100000003

The compound bar containing steel bronze and aluminum segments carries the axial loads shown in the figure. The properties of the segments are listed in the table. Determine the maximum allowable value of P in pounds if the change in length of the entire bar is limited to +0.07in. A (in2) E (psi) L (FT) Steel 0.75 300000002 Bronze 1 120000004 Aluminm 0.5 100000003

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The steel bar has the original dimensions shown in the figure. If it is subjected to an axial load of 50 kN, determine the change in its strength in mm at section a-a. Est = 200 GPa, vst = 0.29
The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected to an axial load of 50 kNkN. Est=198 GPa�st=198 GPa, νst=0.32�st=0.32.
33333. From the given beam loaded as shown, Let P = 3 kN, L = 7 m, a = 3 m. E = 200GPa, I = 2000 x 10^6mm^4
The compound bar ABCD has a uniform cross-sectional area of 0.28 in2.Determine the change in length (in inches) of the bar if an axial force P = 3676 lbis applied.The moduli of elasticity are 29037 ksi for steel and 10006 ksifor aluminum. Round off the final answer to four decimal places.
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.75 in2, 1.08 in2, and 0.56 in2 respectively.Determine the change in length (in inches) of the bar if P = 11599 lb.The moduli of elasticity are 30022 ksi for steel ,12071 ksifor bronze, and 10028 ksi for aluminum. Round off the final answer to four decimal places.
Given Y = 9.79 kN/m^3 Find: P @ bottom of tank (kpa) Force (tensile) on each bolt (kN) Stress on each bolt (MPa)
Before a load is applied, a rigid bar is fastened to two vertical rods. Calculate the vertical movement when P = 50Kn is used. Area(mm2) length E ALUMINUM 500 4m 70Gpa STEEL 300 3m 200Gpa
please sir solve accurate and fast. ( of possible solve compyuterised) THANKS a 30m weighing 0.900kg has a cross-sectional area 0.0485cm^2. the tape measures 30.000m when supported throughout under a tension of 5kg. the modulus of elasticity is 2.1x10^6kg/cm. what tension is required to make the tape measure 30m when supposed only at the two ends?
A 2 m long steel wire is fixed and hanging vertically with a tensile loadof 2 kN and causes it to stretch by 4 mm. Determine the diameter ofthe steel wire when the modulus of elasticity is 205 GPa.A. 3.5 mm B. 5.5 mm C. 4.5 mm D. 2.5 mm
The cross section of a continuous one way slab in a building is shown in the figure. The slabs are supported by means of beams that span 3.6 m between simple supports. The dead load on the slab is 3 kPa (besides its own weight) and a live load of 7 kPa. =21 MPa, =276 MPa. Use 20 mm clear cover. Unit weight of concrete = 24 kN/m3.a) Determine the thickness of slabb) Determine the spacing of 16 mm bars at section CDc) Determine the spacing of 16 mm bars at section E.
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 6 (Example: 4QT mm2 = 406 mm2). Just substitute the number in letter. Thank you! A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 4QT mm2. Determine the average axial stress in each bar.
REFER TOTHE GIVEN VALUES IN THE FIGURE BELOW. THANK YOU. Use VIRTUAL WORK METHOD and determine the following unknowns on the truss system shown below. Use A = 500 mm2 and E = 200 GPa. Show complete and organized solution. Round-off your answers to two decimal places. - Horizontal displacement of joint G due to the applied loads in mm - Horizontal displacement of joint C considering that the top chord members experience 60 °C increase in temperature in mm. Use α = 10-6/°C