Problem 7.1. The aluminum bar (cross section 3 cm x 3 cm) shown the figure below is loaded to its rield point. The modulus of elasticity is 69 GPa, the yield strength in tension is 255 MPa, and Poisson's atio is 0.3. What the dimensions after applying the load. Neglect the weight of the bar. L=2.5 m TF

Problem 7.1. The aluminum bar (cross section 3 cm x 3 cm) shown the figure below is loaded to its rield point. The modulus of elasticity is 69 GPa, the yield strength in tension is 255 MPa, and Poisson's atio is 0.3. What the dimensions after applying the load. Neglect the weight of the bar. L=2.5 m TF

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 404 mm2, 642 mm2 , and 271 mm2 respectively.Determine the change in length (in mm) of the bar if P = 28943 N.The moduli of elasticity are 80.75 GPa for bronze ,73.14 GPafor aluminum , and 203.66 GPa for steel . Round off the final answer to four decimal places.
A compressive load of 50 KN is applied 150 on the axis of a steel-round bar of 8 mm diameter. Compute its stress and strain if the given modulus of elasticity is 75 GPa. Please draw a figure.
A cylindrical rod of steel (E = 207 GPa),4mm in diameter is to be deformed by atensile force. Determine the force (in N)that will produce an elastic reduction of2.5 x 10-3mm in diameter if Poisson’sratio is 0.30. Show complete solution and formulas used.
A joint is made by gluing two plywood gussets of thickness t = 0.56 in to wood boards. Determine the tensile stress for the plywood (in psi) if the dimension b = 12.65 in and the applied force is P = 7475 lb. Round off the final answer to three decimal places.
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 448 mm2, 622 mm2 , and 265 mm2 respectively.Determine the change in length (in mm) of the bar if P = 27199 N.The moduli of elasticity are 81.82 GPa for bronze ,73.92 GPafor aluminum , and 204.55 GPa for steel .
A rectangular steel section with a base of 200 mm and a depth of 400 mm is used as a beam. 51. Determine the elastic section modulus of the beam (x10^6 mm^3). Determine the plastic section modulus of the beam (x10^6 mm^3). What is the shape factor of the beam?
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are 0.75 in2, 1.08 in2, and 0.56 in2 respectively.Determine the change in length (in inches) of the bar if P = 11599 lb.The moduli of elasticity are 30022 ksi for steel ,12071 ksifor bronze, and 10028 ksi for aluminum. Round off the final answer to four decimal places.
Calculate the plane stresses involved where two pieces of steel are welded together. Our sign convention defines forces causing the object to be in tension positive and forces causing the object to be in compression negative. As we can see from the picture our σx = −4.5MPa and σy = 10MPa. Steel has an average Young’s modulus of elasticity of E = 200 GPa and an average Poisson’s ratio of ν = .285 Because it is not defined we will assume that initially there is no shear stress, τxy = 0. Solve only for: Compression in the x-direction(deformation along the weld)=(-Blank 4)? x 10^-5
Determine the plastic section modulus Zx and elastic section modulus Sx