The compound beam is fixed at E and supported by rollers at A and B. There are pins at C and D. Take F = 1700 lb. (Figure 1) Part A Determine the reaction at support A. Express your answer in kilopounds to three significant figures. ΜΕ ΑΣΦ ΑΣΦ 1 vec A 1.840 Submit Previous Answers Request Answer Part B Incorrect; Try Again; 3 attempts remaining Determine the reaction at support B. Express your answer in kilopounds to three significant figures. ΑΣΦ 1 vec By 1.020 You have already submitted this answer. Enter a new answer. No credit lost. Try again. Submit Previous Answers Request Answer ? kip ? kip

The compound beam is fixed at E and supported by rollers at A and B. There are pins at C and D. Take F = 1700 lb. (Figure 1) Part A Determine the reaction at support A. Express your answer in kilopounds to three significant figures. ΜΕ ΑΣΦ ΑΣΦ 1 vec A 1.840 Submit Previous Answers Request Answer Part B Incorrect; Try Again; 3 attempts remaining Determine the reaction at support B. Express your answer in kilopounds to three significant figures. ΑΣΦ 1 vec By 1.020 You have already submitted this answer. Enter a new answer. No credit lost. Try again. Submit Previous Answers Request Answer ? kip ? kip

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.6P: An idealized column consists of rigid bar ABCD with a roller support at B and a roller and spring...

See similar textbooks

Similar questions

A propped cantilever beam, fixed at the left-hand end A and simply supported at the right-hand end B, is subjected to a temperature differentia] with temperature T1on its upper surface and T2on its lower surface (see figure).
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Repeat Problem 6.2-1 but now assume that the steel plate is smaller (0.5 in. × 5 in.) and is aligned with the top of the beam as shown in the figure.
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
A column, pinned at top and bottom, is made up of two C 6 x 13 steel shapes (see figure) that act together. Find the buckling load (kips) if the gap is zero. Find required separation distance d(inches) so that the buckling load is the same in y and z directions. Assume that E = 30,000 ksi and L = 18 ft. Note that distance d is measured between the centroids of the two C shapes.
An idealized column consists of rigid bar ABCD with a roller support at B and a roller and spring support at D. The spring constant at D. is ß = 750 N/m. Find the critical load Pcrof the column.
Continuous cable A DB runs over a small friction less pulley al D to support beam OABC, which is part of an entrance canopy for a building (see figure}. The canopy segment has a weight W = 1700 lb that acts as a concentrated load in the middle of segment AB. (a) What is the maximum permissible value of load P at C if the allowable force in the cable is 4200 lb? (b) If P = 2300 lb, what is the required diameter of pins A, B, and D? Assume that the pins are in double shear and the allowable shear stress in the pins is 10 ksi.
Continuous cable ADB runs over a small friction less pulley at D to support beam OABC, which is pan of an entrance canopy for a building (see figure). A downward distributed load with peak intensity q0= 5 kNVm al O acts on the beam (see figure). Assume that canopy weight W = S kN and that the cable cross-sectional area is 100 mm". What is the required diameter of pins A, B. and D if the pins are in double shear and the allowable shear stress is SO MPa? Note that dimensions OA = AB = BC = 1.5 m.
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
An aluminum box column with a square cross section is fixed at the base and free at the top (sec figure). The outside dimension b of each side is 100 mm and the thickness t of the wall is 8 mm. The resultant of the compressive loads acting on the top of the column is a force P = 50 kN acting at the outer edge of the column at the midpoint of one side. What is the longest permissible length Lmaxof the column if the deflection at the top is not to exceed 30 mm? (Assume E = 73 GPa
Segments AB and BCD of beam ABCD are pin connected at x = 10 ft. The beam is supported by a pin support at A and roller supports at C and D; the roller at D is rotated by 30* from the x axis (see figure). A trapezoidal distributed load on BC varies in intensity from 5 lb/ft at B to 2.5 lb/ft at C. A concentrated moment is applied at joint A, and a 40-lb inclined load is applied at the mid-span or CD. (a) Find reactions at supports A, C, and D. (b) Find the resultant force in the pin connection at B. (c) Repeat parts (a) and (b) if a rotational spring(kr= 50 ft-lb/radian ) is added at A and the roller at C is removed.
A long slender column ABC is pinned at ends A and C and compressed by an axial force F (sec figure). At the midpoint B, lateral support is provided to prevent deflection in the plane of the figure. The column is a steel wide-flange section (W 250 × 67) with E = 200 GPa. The distance between lateral supports is L = 5.5 m. Calculate the allowable load P using a factor of safety n = 2.4, taking into account the possibility of Eu 1er buckling about cither principal centroidal axis (i.e., axis 1-1 or axis 2-2).