The concrete beam shown below is made of an all-lightweight concrete with a unit weight y =1850 kg/m. a. Compute the value of the cracking moment and b. Estimate the value of the concentrated load P at midspan that causes the beam to crack (include the dead weight of the beam). fe = 27.6 MPa 100 mm P=? Wbeam 2-D25 - 4.2 m 100 mm 100 mm 300 mm 40 mm

The concrete beam shown below is made of an all-lightweight concrete with a unit weight y =1850 kg/m. a. Compute the value of the cracking moment and b. Estimate the value of the concentrated load P at midspan that causes the beam to crack (include the dead weight of the beam). fe = 27.6 MPa 100 mm P=? Wbeam 2-D25 - 4.2 m 100 mm 100 mm 300 mm 40 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

A reinforced concrete beam of rectangular section has the cross-sectional dimensions shown in the figure below. The concrete of normal density has a compressive strength of 30 MPa and a modulus of rupture of 3.3 MPa. The yield strength of steel is 400 MPa. a) Calculate the stress due to an applied bending moment of 45 kN-m b) Calculate the bending moment at which cracking of concrete will be initiated (cracking moment Mcr) h=600 mm b=300 mm 키 As-2000 mm 4- No 25 d=530 mm
The concrete beam shown below is made of an all-lightweight concrete with a unit weight 7=/ 800 kg/ ni a. Compute the value of the cracking moment and b. Estimate the value of the concentrated load P at midspan that causes the beam to crack (include the dead weight of the beam). f, =27.5 MPa 100 mm P=? Wbeam 2-D25 - 5 m 100 mm 100 mm 300 mm
The compound bar, composed ot the three segments shown, is initially stress-free. Compute the stress in the Steel segment if the temperature drops 25°C. Assume that the walls do not yield and use the following data: A (mm²) a (/°C) 11.7x10-6 E (GPa) Steel 800 200 Bronze 1400 19.0 x10-6 83 Aluminum 2000 23. 0 x10-6 70 800 mm 500 mm- -400 mm→ Steel Bronze Aluminum Select one: O a. 11.94 MPa O b. 59.21 MPa O c. 78.95 MPa O d. 15.92 MPa Next page
> * The state of two-dimensional stresses acting on a concrete lamina consists of a direct tensile stress o. = 1.5 N/mm² and shear stress T = 1.20 N/mm², when cracking of concrete is just impending. The permissible tensile strength of the concrete is
A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION,20mm WIDE IN THE Z DIRECTION AND 25mm THICK IN THE XDIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF AUNIFORMLY DISTRIBUTED FORCE OF Px=3kN (COMPRESSION), Py=4kN(TENSION) AND Pz=7kN (COMPRESSION) IN THE X, Y AND Z DIRECTIONSRESPECTIVELY. IF THE POISSON’S RATIO = 1/4 & E = 70 GPa,DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSODETRMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THEWOULD PRODUCE THE SAME X DEFORMATION AS THE ORIGINAL.
F 1. The "slump" test is used to determine the compressive strength of a concrete. T 2. For room temperature and axial loading,aluminum behaves as a brittle material. T. F 3. Proper curing is important for a concrete specimen to gain compressive strength. (F) 4. Concrete usually has a good tensile strength. T F 5. The units of the modulus of elasticity are the same as for axial stress. F 6. Plasticity is characterized by return of a material to original size & shape upon removal of stress. T. F 7. Strain hardening increases the elastic strength of the material. F 8. Some materials do not exhibit a well defined yield point. F 9. The failure behavior of our aluminum specimen in our torsion test was expected. T. T F 10. Necking of a steel specimen loaded in tension is an example of Poisson's ratio.
A RECTANGULAR ALUMINUM BLOCK IS 40mm LONG IN THE Y DIRECTION, 20mm WIDE IN THE Z DIRECTION AND 25mm THICK IN THE X DIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF A UNIFORMLY DISTRIBUTED FORCE OF Px=3 (COMPRESSION), Py=6 (TENSION) AND Pz=9 (COMPRESSION) IN THE X, Y AND Z DIRECTIONS RESPECTIVELY. IF THE POISSON’S RATIO = 1/4 & E = 70 GPa, DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSO DETRMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THE WOULD PRODUCE THE SAME X DEFORMATION AS THE ORIGINAL.
F 1. The "slump" test is used to determine the compressive strength of a concrete. (F) 2. For room temperature and axial loadingaluminum behaves as a brittle material. T. T 3. Proper curing is important for a concrete specimen to gain compressive strength. T. (F 4. Concrete usually has a good tensile strength. T F 5. The units of the modulus of elasticity are the same as for axial stress. T F 6. Plasticity is characterized by return of a ħaterial to original size & shape upon removal of stress. т F 7. Strain hardening increases the elastic strength of the material. T F 8. Some materials do not exhibit a well defined yield point. T F 9. The failure behavior of our aluminum specimen in our torsion test was expected. T F 10. Necking of a steel specimen loaded in tension is an example of Poisson's ratio.
An aluminum pipe must not stretch more than 0.05in when it issubjected to a tensile load. Knowing that E=10.1x10^6psi and that the maximum allowable normal stress is 14ksi, determine (a) the maximum allowable length of the pipe, and (b) the required area of the pipe if the tensile load is 127.5kips.
The modulus of elasticity of "reinforced concrete" in RC design, is O A. 420 GPa B. 200 GPa C. None () D. 220 GPa
A composite column is formed by placing a steel bar, 20 mm in diameter and 200 mm long, inside an alloy cylinder of the same length whose internal and external diameters are 20 mm and 25 mm, respectively. The column is then subjected to an axial load of 50 kN. If E for steel is 200 OOO N/mm’ and E for the alloy is 70 000 N/mm’, calculate the stress in the cylinder and in the bar, the shortening of the column and the strain energy stored in the column.
This course EHide blocks An aluminum pipe is filled in concrete is subjected to a pure compressive force as shown in the figure below. Determine the factor of safety against compressive stress acting on the column. The pipe has an outer diameter of 45 mm and inner diameter of 35 mm. The aluminum and the polymer concrete have the following material properties: Young's modulus: Eal = 70 GPa (aluminum), Ecr = 30 GPa (concrete). Yield compressive strength: Sy-al = 180 MPa (aluminum), Sy-cr 60 MPa (concrete). 100 kN 500 mm Select one: O FS = 1.5 O FS = 1.7 O ES- 19 5:45 PM 86°F Light rain ENG 6/18/2021