b) An input voltage source Vs of 130mV RMS and an internal resistance Rs of 100is connected to an amplifier that has an input impedance of 3.3kN, a voltagegain of 150 and an output impedance of 220N. The output of the amplifier isconnected to a speaker that has a load resistance of 2.7kN.Determine the output voltage across the speaker.Calculate the effective voltage gain.(s)ks)ks)i.ii. Explain how the effective gain can be increased.

Answered: Image /qna-images/answer/d1ddf025-598e-442a-861a-3b6527aac571.jpg

b) An input voltage source Vs of 130mV RMS and an internal resistance Rs of 100 is connected to an amplifier that has an input impedance of 3.3kN, a voltage gain of 150 and an output impedance of 2202. The output of the amplifier is connected to a speaker that has a load resistance of 2.7kn. Determine the output voltage across the speaker. Calculate the effective voltage gain. i. ii. iii. Explain how the effective gain can be increased.

b) An input voltage source Vs of 130mV RMS and an internal resistance Rs of 100 is connected to an amplifier that has an input impedance of 3.3kN, a voltage gain of 150 and an output impedance of 2202. The output of the amplifier is connected to a speaker that has a load resistance of 2.7kn. Determine the output voltage across the speaker. Calculate the effective voltage gain. i. ii. iii. Explain how the effective gain can be increased.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How experimental setup is prepared for a CB transistor configuration. Draw its h-parameter model. Find amplifier parameters given below using this model- (i) Current gain (ii) Input impedance (iii) Voltage Amplification (AVS) consideration source impedance (iv) Current Amplification (AIS) consideration source impedance
An amplifier operating from a ±15 V DC supply provides an output voltage of 20 V peak-to-peak and an output current of 23 mA peak to a resistive load when a signal of 2 V peak is connected to its input. The current drawn by the input port of the amplifier is 2 mA rms. A current of 15 mA DC is provided by each DC power supply. For this amplifier, calculate: the voltage gain in dB the current gain in dB the power gain in dB the efficiency (as a percentage) the input resistance in Ohms
Use BJT transistor to design an amplifier circuit that operates in the frequency range 10kHz-100kHz. Verify your design by simulating the design using the circuitmaker or multisim software. Use the standard resistor values (10% tolerance). The design should meet the following criteria: 1. Good stabilization of the Q-point 2. VCEQ is around ½ VCC. 3. High voltage and Current gain. From your design and simulation results, determine the following: a. β of the transistor b. VCEQ c. The voltage gain (AV) Please provide us with your simulation file and a report about your results
Figure Q1(a) shows a Class A power amplifier circuit. Given the output signal is as shown in the figure, where Vm is the peak voltage and T is the period. For all transistors, you may neglect VBE and VCE(sat) in your calculations. (i) Derive an equation for power conversion efficiency, in terms of Vm, VCC, I and RL. Hence, deduce the maximum power conversion efficiency that is achievable. (ii) Determine the worst-case average power dissipation in each transistor under normal condition (i.e. RL is not open or short)
What are the unity-gain frequency and slew rate of the bipolar amplifier as shown if I1 = 100 μA, I2 = 400 μA, and CC = 10 pF? (b) If I1 = 300 μA, I2 = 350 μA, and CC = 10 pF?
Given a Class A amplifier given a VCEq = 10.5V, VCC = 24V, Voltage divider resistors 1kohm and 180ohm, Ic = 40mA. Calculate the Po(ac) = mW (Note this is in mW. Round to the tens place.) Calculate the DC power dissipated = Watts (enter to the tenths place) Calculate the efficiency percentage = % Round to the ones place (no decimal places).
A source with equivalent noise temperature Te = 850 K is followed by a cascade of three amplifiers shown in Table 1.0. Assume a bandwidth is 40 kHz, evaluate the overall noise factor and noise figure of the cascade. In order to get better performance of the amplifier system, you may try to re-arrange the amplifier units. Please prove and justify which arrangement is the best to be chosen.
A common emitter amplifier as shown in Figure Q2 has the following parameters, β = 100, R1= 33K, R2 = 10K, RC = 3K3, RE = 1K, ro =  and VBE = 0.7 V.State all assumptions made.i. Check whether βRE>>10R2 is satisfiedii. Use the appropriate approach of analysis to determine the Quiescent point; IBQ,ICQ and VCEQ.iii. Draw the small signal equivalent circuit. Determine input impedance, Zin, outputimpedance, Zout, and the voltage gain, AV, if RL=20kΩ.
Differential amplifier circuit with resistive load topology and the current source, ISS is 0.2mA. Assume the circuit is symmetrical in which (W/L)1 = (W/L)2 =25/0.5 and μnCox = 50 μA/V2. i)Please evaluate the transconductance, gm and differential small-signal voltage gain, Av. Then, if the aspect ratio (W/L)2 = 2(W/L)1, investigate the effect on the transconductance of transistors M1 and M2. ii)Prove that gm2 = 2gm1.
A three stage amplifier has the following gains and noise factor for each stage: 1st stage Gain=10 dB and Noise Factor = 2; 2nd stage Gain=16 dB and Noise Factor = 4; and 3rd stage Gain=20 dB and Noise Factor = 5. Suppose another amplifier stage (4th stage) is connected, what would be its noise figure (4th stage) in dB to provide as overall noise factor of 2.3? (Use two decimal places)
Given a certain common-source JFET amplifier in the laboratory, RD = 1 KΩ, RS = 560 Ω, VDD = 10 V and gm = 4500 uS. If the source resistor is completely bypassed, what is the voltage gain? _________- (hint: the voltage gain is the product of total AC load resistance and transconductance. Getting the total AC load resistance is equal to the parallel of load resistance and RD for loaded circuit)."
The ac equivalent circuit for an amplifier is shown. Assume the capacitors have infinite value, RI = 100 kΩ, RG = 6.8MΩ, RD = 50 kΩ, and R3 = 120 kΩ. Calculate the voltage gain for the amplifier if the MOSFET Q-point is (100 μA, 5 V). Assume Kn = 450 μA/V2 and λ = 0.02 V−1.