A rotary shaft carries distributed load of 250 w/m with a long 3m. The shaft transmits 35 KW at 290 rpm. A shaft is simply supported shaft. The mux. shear stresses 56 MPa and the allowable Compression stress 45 MPa, the safety factor is 1.5. Find the size of the shaft if it subjected to suddenly applied load.

A rotary shaft carries distributed load of 250 w/m with a long 3m. The shaft transmits 35 KW at 290 rpm. A shaft is simply supported shaft. The mux. shear stresses 56 MPa and the allowable Compression stress 45 MPa, the safety factor is 1.5. Find the size of the shaft if it subjected to suddenly applied load.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Similar questions

Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
A W 360 x 79 steel beam is fixed at A. The beam has a length of 2.5 m and is subjected to a linearly varying distributed load with maximum intensity q0= 500 N/m on segment AB and a uniformly distributed load of intensity qQon segment EC. Calculate the state of plane stress at point D located 220 mm below the top of the beam and 0\3 m to the left of point B. Find the principal normal stresses and the maximum shear stress at D. Include the weight of the beam, See Table F-l(b), Appendix F, for beam properties.
Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A thin tubular shaft with a circular cross section (see figure) and with inside diameter 100 mm is subjected to a torque of 5000 N · m. If the allowable shear stress is 42 MPa, determine the required wall thickness t by using (a) the approximate theory for a thin-walled tube and (b) the exact torsion theory for a circular bar.
A pressurized cylindrical tank with flat ends is loaded by torques T and tensile forces P (sec figure), The tank has a radius of r = 125 mm and wall thickness t = 6.5 mm. The internal pressure p = 7.25 MPa and the torque T = 850 N m. (a) What is the maximum permissible value of the forces P if the allowable tensile stress in the wall of the cylinder is 160 MPa? (b) If forces P = 400 kN, what is the maximum acceptable internal pressure in the tank?
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
A circular steel tube of length L = 1.0 m is loaded in torsion by torques T (see figure). (a) If the inner radius of the tube is r1= 45 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y1(in radians) at the inner surface? (b) If the maximum allowable shear strain is 0.0004 rad and the angle of twist is to be kept at 0.45° by adjusting the torque T, what is the maxi mum permissible outer radius (r2)max?
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
Solve the preceding problem for a welded Tank with a = 62°,r = 19 irM = 0.65 in.,p = 240 psu E = 30 X 106 psi, and v = 0.30