The demand and forecast for February are 12000 and 10275, respectively. Using single exponential smoothening method (smoothening coefficient =0.25), the forecast for the month of March is (a) 431 11000

The demand and forecast for February are 12000 and 10275, respectively. Using single exponential smoothening method (smoothening coefficient =0.25), the forecast for the month of March is (a) 431 11000

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer the following questions based on scaling arguments, i.e., by applying “the variable X must be proportional to the Zth power of variable Y because of some relevant physical principle”-type reasoning. A. In a surface passivation process for Si wafers, the required processing time to create a 0.1 micron thick SiO2 layer on a pure Si wafer was 2 hours. Estimate the process time required to create an SiO2 layer of thickness 0.15 microns on a pure Si wafer under identical processing conditions. B. A puddle of volatile liquid of initial thickness of 1 cm was found to evaporate to form a thinner 0.5 cm layer in 1 day. How much longer would it take for the liquid layer to evaporate completely?
"You did calculations using the simplified HAZ time-temperature formulas, assuming 3D heat flow, and are presenting your final internship conclusions to management. You realize with horror, in the middle of your presentation, that you forgot to label your calculated curves (below). Which curve is which? Pick the best answer A: "Plot 1 is HYPERFILL® and Plot 2 is p-GMAW. Since HYPERFILL® has the higher heat input, it cools more slowly." B: "Plot 2 is HYPERFILL® and Plot 1 is p-GMAW. Since HYPERFILL® has the faster travel speed of the two processes, it cools faster." C: "Plot 1 is p-GMAW and Plot 2 is HYPERFILL®. Since p-GMAW has the slower travel speed, it cools more slowly." D: "Plot 2 is p-GMAW and Plot 1 is HYPERFILL®. Since p-GMAW has the lower heat input, it cools faster" Both (A) and (D)
Using inferential, experimental, and simulation approaches in research. How are the quantitative data obtained using each?
A sand mixture was screened through a standard 12 mesh screen. The mass fraction of the oversize material in feed, overflow, and underflow were found to be 0.4, 0.8, and 0.2 respectively. Calculate the screen effectiveness where the oversize material is the product, and the overall screen effectiveness. Please show full solution and use 4 decimal places.
What is difference between error terms (disturbance) and residual? Demonstrate and explain
What is the orientation geometric tolerance that is applied to this feature?: __________ Does the tolerance control a surface, axis, or center plane?: __________ What is the applied tolerance if the feature is produced at MMC?: __________
I want to know what type of temperature sensor can be used to obtain the melting point temperature of a wax. I want to know what type of temperature sensor is better to be in contact with this type of fluid and why. (if you could give me an explanation) thanks
Explain what material properties link to nozzle and bed temperature. Plot a graph of the process windows of nozzle temperature and print bed temperature representing the 3D FDM printing temperature range for a material X. The Melting Point of X is the 2nd, 3rd and 4th digit of your student ID and the Tg of X is the 5th and 6th digit of your student ID. If your second digit is 0, use from the 3rd digit to the 7th digit. Eg: Student ID 216456783, Mp = 164°C & Tg = 56°C.
The principles of Newton’s Law of Cooling. You can imagine and create your own data. Discuss the nature and origin of the four (4) types of coffee where it originates. Various settings, formulations, containers, and the number of trials will be properly discussed in their methodology. Once the experimentation has been done, the thermal coefficient shall be computed and recorded. The temperature coefficient acquired at t=0 and t= 5 mins, will be tested at t = 6,7,8,9 and 10 minutes.
Alplas Plastics uses an extruder in which the barrel diameter = 0.4 m and length = 6.0 m. The extruder screw rotates at 65 rev/min; it has channel depth = 0.02 m and flight angle = 16°. The plastic melt has a shear viscosity = 85 Pa-s. Determine: (a) Qmax and pmax; (b) the shape factor Ks for a circular die opening in which Dd = 0.009 m and Ld = 0.03 m; and (c) the values of Q and p at the operating point
After the sinking of RMS Titanic, US operated the International Ice patrol with the purpose of monitoring the presence and movements of icebergs in the Atlantic and Arctic oceans. Once, they observed a unique tabular iceberg in a form of a rectangle (250 km x 50 km x 300 m). How many years would it take to melt the iceberg solely by heat from the sun if the ice absorbs a mean of 98 J/m2 -s, 12.5 hrs per day? Note: the exposed area for heating is 250 km x 50 km and the density is 920 kg/m3 . This is my solution.
a.) What would the air velocity ua in a cleanroom have to be to produce a characteristic length equivalent to the width of a 0.01m diameter line, taking the Reynolds number Re = 10 (typical for a cleanroom) or 2300 (upper bound for laminarity)? b.) Why is the velocity at the lower end of the range impractical? c.) Given typical cleanroom parameters for Re and ua, what is the characteristic length we actually have to work with?