The disk A rotates about the vertical z-axis with a constant speed w = = π/3 rad/s.Simultaneously, the hinged arm OB is elevated at the constant rate = 2/3 rad/s. At time t = 0,both 0 = 0 and y = 0. The angle is measured from the fixed reference x-axis. The small sphere Pslides out along the rod according to R = 50+ 200t2, where R is in millimeters and t is in seconds.Determine the magnitude of the total acceleration a of P when t = 1/2 s.R(0)BPAØ

Answered: The disk A rotates about the vertical…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

find an acceleration of the center of the beam (marked as a blue point) which is connecting both wheels , if it is known that linear velocity ot the wheels v=100km/h, r=0,8m and the distance drom the center of the wheel and the pont where the beam is connected (marked as red red distance)=0,4m, there is no slipping between wheels and the ground
A disk with mass m = 6.5 kg and radius R = 0.39 m hangs from a rope attached to the ceiling. The disk spins on its axis at a distance r = 1.32 m from the rope and at a frequency f = 18.9 rev/s (with a direction shown by the arrow). what is the torque due to gravity on the disk? what is the period of precession for this gyroscope? what is the direction of precession of the gyroscope?
(The complete question is in the picture) A disk rotates with constant angular acceleration about an axis passing through its center of mass. At an instant, its angular speed is measured to be 20.0 [rad/s]. What is the angular speed of the disk after 2.00 [s] if it has revolved by 60.0 [rad] during this timeinterval? A. 10.0 [rad/s]B. 20.0 [rad/s]C. 30.0 [rad/s]D. 40.0 [rad/s]
Find the sum of the three harmonic motions: x1(t)=10cos(wt + 2) x2(t)=15sin(wt + 2) x3(t)= 15cos(wt)
A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and accelerates uniformly to omega = 24 rpm in t= 10 sec and maintain then maintain this constant 24 rpm speed. The dimensions are rA= 1 in, rB= 9 in and rC=16 in. 2) After 10 sec, find the distance s2 in feet and in NC es needed to reach the 11 ft, find thetaC2(t), alphaA2, alphaB2 in rad/s^2, omegaA2(t), omegaB2(t) in rad/s, thetaA2(t), in rad and the distance s2 in ft that should be made to get to the 11 ft raising distance of the load. 3) Deduce the number of revolutions made by gear A and how long it will take, to raise the load up to 11 ft.
The disk with radius r = 0.2 m (figure below) starts from rest and receives an angular acceleration at clockwise given by alfa= (3t3)rad/s2, where t is given in second. That said, for t = 3 s determine: (a) the angular velocity of the disk (b) the velocity intensity of a point P on the edge of the disk. Represent the direction of the velocity vector at point P indicated in the figure (c) the intensities of the normal and tangential components of the acceleration of a point P in the edge of the disc. Plot the direction of these acceleration components at the indicated point P in the figure
The 250 g disk shown spins at the rate w1 = 750 rpm, while axle AB rotates as shown with an angular velocity ω2 of 6 rad/s. Find the Kinetic energy of the disk with this information.
While the system shown is in equilibrium, a counter-clockwise torque T =T0sin(ωt) N-m(with T0 = 226.6 and ω=7) is applied to teh disk. What is the disk angular speed ω0 = ? in rad/s at time t = 4.2 sec? ( I = 0.2 kg.m2, b = 7.8 N-m-s/r, k = 1,504 N/m, r = 0.52m )
A 3 in radius disk spins at the constant ω1 - 5 radian/s and a constant rate ω2= 4 radians/s. If the angle is 45 degrees, find the absolute acceleration at point P.
The constant angular acceleration of the rotating disk is 12 rad/s . The angular velocity of the disk is 24 rad/s clockwise when t = 0. Determine the total angle turned by the disk between t = 0 and t = 4sec. the answer is 48 rad. show your solution.
Form the Equation of Motion (EOM) [ma + cv + kx = p(t)] for the following structure.
Two smooth disks A and B each have a mass of 0.5 kg. Both disks are moving with the velocities shown when they collide. Suppose that (vA)1 = 9 m/s , (vB)1 = 8 m/s. The figure shows two discs, A and B, moving toward the origin of a horizontal xy-plane, where they collide, so that their common tangent lies on y-axis. Disk A moves in negative x-direction with velocity left-parenthesis v subscript A right-parenthesis subscript 1. Block B moves from the third quarter with velocity left-parenthesis v subscript B right-parenthesis subscript 1, directed along an inclined line with a slope of four-thirds. Determine the coefficient of restitution between the disks if after collision B travels along a line, 30∘ counterclockwise from the y axis.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS