Solve it completely and correctly please. I will rate accordingly. The distributed load of w = (-2x² + 4x + 16) lb/ft acts on thebeam as shown(Figure 1).Part ADetermine the maximum intensity wmar ·Express your answer with the appropriate units.UHAValueUnitsWmaz =SubmitPrevious Answers Request AnswerX Incorrect; Try Again; 5 attempts remainingPart BWhat is the magnitude of the equivalent resultant force?Express your answer with the appropriate units.Figure1 of 1µAFR =ValueUnits-w = w (x)SubmitRequest AnswerPart CSpecify where it acts, measured from point B.4 ftExpress your answer with the appropriate units. Part CSpecify where it acts, measured from point B.Express your answer with the appropriate units.µA?d =ValueUnitsSubmitRequest Answer

Answered: Image /qna-images/answer/2e9d89f4-459b-448a-8dbf-6dcd51a2f10e.jpg

Answered: The distributed load of w = (-2x² + 4x…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.12.4P

See similar textbooks

Similar questions

A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
A prismatic bar of length L = 1.8 m and cross-sectional area A = 480 mm" is loaded by forces P{= 30 kN and A = 60 kN (see figure) The bar is constructed of magnesium alloy having a stress-strain curve described by the Ram berg-Osgood equation: 45.000 618 UW id which u has units of mega pascals (MPa). (a) Calculate the displacement 8t- of the end of the bar when the load P:acts alone. (b) Calculate the displacement when the load P, acts alone. (c) Calculate the displacement when both loads act simultaneously.
.16 Three identical, solid circular rods, each of radius r and length L, are placed together to form a compression member (see the cross section shown in the figure). Assuming pinned-end conditions, determine the critical load Pcr The rods act independently as individual columns. The rods are bonded by epoxy throughout their lengths so that they function as a single member. What is the effect on the critical load when the rods act as a single member?
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
The figure shows an idealized structure consisting of two rigid bars joined by an elastic connection with rotational stiffness ßR. Determine the critical load PCTfor the structure.
The figure shows an idealized structure consisting of rigid bars ABC And DEF joined by a linearly elastic spring ß between C and D. The structure is also supported by translational elastic support ß at B and rotational elastic support ßRat E. Determine the critical load Pcrfor the structure.
Determine the largest intensity of the distributed load ww and its length xx on the beam so that the beam remains in the horizontal position when it is loaded. Express your answers, separated by a comma, to three significant figures. Given: The rigid beam is supported at its ends by two A-36 steel tie rods. (Figure 1) The rods have diameters dAB=0.51 in.dAB=0.51 in. and dCD=0.29 in.dCD=0.29 in. The allowable stress for the steel is σallow=16.6 ksiσallow=16.6 ksi.
choose one: AB (in compression) AB (in tension) AE (in compression) AE (in tension) BE (in compression) BE (in tension) DE (in compression) DE (in tension) DH (in compression) DH (in tension) EF (in compression) EF (in tension) Using the same diagram, what is the maximum magnitude of compression or tension in any one beam in the truss if m = 119 g? Give your answer with 3 sig figs in units of Newtons. Do not include the units in your answer.
Question 1) in FIG loading condition is given beam F force F = 65 kN , first distributed load W 1 = 41 kN / m , w 2 distributed load w 2 = 51 kN / m , θ angle θ = 48 ° and L length of L = 5 m . According to this; Question 1-A) B at the point y direction ( B y ) Determine the support reactions. (Enter yourresultwithout writing kN units.) Question 1-B) to the point in y direction ( A y ) Determine the support reactions. ( Enter yourresult without writing kN units.) Question 1-C) to the point in x direction ( A x ) Determine the support reactions. ( Enter yourresult without writing kN units.)
9-8kN stress/force on the AB rope holding the base station shown below There are. In order for the net force at point A of this base station to be downward What is the stress/force that should be on the AC rope? A) 5556 N C) 7356 N B) 8200 N D) 3648 N E) 1228 N
The following figure shows the critical position of a crane that supports 2.5 Tons of load by means of a chain. You are delegated the responsibility of building a crane with similar geometric characteristics and load capacity. The diagram of free body of the crane arm can be redrawn as follows. (check the attached image "fbd") Assuming that the crane arm will be made of steel with yield stress sigmaY =220 MPa and that you must consider a safety factor of F.S.=1.5, propose a profile from the following catalog for the manufacture of the crane arm. Ignore the effects of shear forces on this element. On the other hand, it is very important that you consider the effects of axial loads. Commercial profiles for arm construction. (Check image "profiles")

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS