The figure below is a bracket which fastened by a bolts with a diameter of 0.5 inch. Compute the corresponding shear stresses. Assume single shear. Note: Round off your answer in two decimal places. ... 45° MN Ib B 12 in. AO 36 in.-

The figure below is a bracket which fastened by a bolts with a diameter of 0.5 inch. Compute the corresponding shear stresses. Assume single shear. Note: Round off your answer in two decimal places. ... 45° MN Ib B 12 in. AO 36 in.-

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Related questions

Q: Consider a nuclear power plant operating on the ideal Rankine cycle with steam as the working fluid....

Q: A cylindrical bar, whose lateral surface is constrained so that there can be no lateral expansion, i...

Q: Problems: Determine the standard differential equation of the figure below. a. Using movement of blo...

Q: The curve surface represented by AB in the figure is the surface of the quadrant of a circular cylin...

Q: What is the theoretical minimum pressure possible in the condenser if it is being cooled by river wa...

Q: A ship weighing 7200 tons has a KG of 5.20 m, a KB of 3.12 m and a KM of 5.35 m. In the voyage, has ...

Q: The demand and forecast for February are 12000 and 10275, respectively. Using single exponential smo...

A: Given:Demand for feb, D=12000forecast for feb, F=10275smoothening coefficient, μ=0.25

Q: Write one simple case study on Turbojet Engine.

A: Turbojet Engines are gas turbine engines that are used in aircraft and other aerospace applications....

Q: kN (i) m of water (ii) mm of mercury (i) abs.

A: given- Patm= 75 cm of Hg P= 10N/cm2

Q: In a steam power plant, the condenser pressure is 10 kPa. The turbine and pump isentropic efficienc...

Q: 9. The boom AC in the figure rests in a ball and socket joint at A and is held in equilibrium by the...

A: An object is considered to be in a condition of equilibrium when all of the forces acting on it are ...

Q: A rigid tank holds 20 lbm of air at a pressure of 20 psi and a temperature of 70°F. Increase the amo...

Q: Identify shortly the parts of the stress-strain. Briefly explain each part.

A: Stress is define as the ratio of restoring force and the cross section area. It's formula is σ=P/A ...

Q: demonstrate 10) Torricelli's equation, in the form parameterized by the trajectory (make an illustr...

A: given; 10) Torricelli's equation, in the form parameterized by the trajectory (make an illustration)...

Q: Using the method of section, or otherwise, determine the forces in the members GF and HF for the tru...

Q: Water is used to cool ethylene glycol in a 60-ft-long double pipe heat exchanger made of 4-std and 2...

A: Given, T1 = 180oF mw = 20 lbm/sec mc = 30 lbm/sec t1 = 60oF From Copper Tubing: 4 - std => IDa = ...

Q: In a single pass rolling process using 412mm diameter steel rollers, strip of width 120mm and thickn...

Q: Consider a round potato being baked in an oven. Would you model the heat transfer to the potato as ...

A: Fourier's law is the foundation of conduction heat transfer. Fourier's law defines thermal conductiv...

Q: A 2-m3 tank contains a saturated vapor at 40oc. Determine the pressure and mass in the tank if the s...

Q: A smooth can C, having a mass of 5 kg, is lifted from a feed at A to a ramp at B by a rotating rod. ...

Q: The stream function o in a two-dimensional flow field is given as p = 4x – 3y + 7xy (a) Prove that t...

Q: r. The service

Q: Determine the force in member CG. The force is positive if in tension, negative if in compression. A...

Q: 5. Consider a 500 kJ/min refrigeration system that operates on an ideal vaporcompression refrigerati...

A: Answer: (a) The quality of the refrigerant at the end of the throttling process is 0.3033. (b) The p...

Q: A component in a refrigeration system is the evaporator. It is here that the cold refrigerant picks ...

Q: Calculate the support reactions at point A and B, and the forces at the hinges (C, D and E) of the p...

A: The free-body diagram of the plane frame is shown below.

Q: As an airplane flying with constant velocity moves from a cold air mass into a warm air mass, how do...

Q: An ROR hydroelectric power plant is operating under the following conditions: • Plant capacity fact...

A: The maximum power output of the plant can be calculated using the formula given below as- P=ρQv2 whe...

Q: A darts player throws a dart horizontally at a board 2m away with speed u. The dart hits the board a...

Q: 6 m A= 180 mm 6 m 4 m B.

Q: A 'U' tube is made of two capillary tubes; one 2 mm in diameter and other 4 mm in diameter. The tube...

Q: a. the total dynamic head in meters b. the water power in kW c. the motor horsepower if the pump e...

Q: An aluminum rod is rigidly attached between bronze rod and steel rod as shown. Axial loads are appli...

A: Given: The maximum value of stress in steel is σs=120 Mpa. The maximum value of stress in aluminum ...

Q: 2. Now consider the pulley problem shown below. In this problem, both blocks have mass m m m (a) At ...

A: Calculated velocity and acceleration of the block on the right side.

Q: PROPAGATION OF ERROR You are tasked to supervise the design of 0.5MW wind turbine to be constructed...

Q: A rubber bolt is inflated to apressure of 65kPa. At that pressure, tediameter of the ball is 240mm a...

Q: A patient needing a blood transfusion has a blood pressure of 120/70 (this is in units of mm Hg). It...

A: NOTE:- As per our company guidelines we are supposed to answer only one question. Kindly repost othe...

Q: A jet plane is launched from a catapult on an aircraft carrier. In 2.0 s it reaches a speed of 151 k...

Q: a)The photon energy of a CO2 laser is 0.117eV. Calculate the wavelength of the laser ( please show t...

A: Given data: Energy of CO2 photon = 0.117 eV

Q: PROBLEM 3: The force R is the resultant of the forces Pl, P2, and P3 acting on the rectangular plate...

Q: vapour leaves the evap

Q: UNIVERSSITY O F LIVERPOOL Ei POL UNIVERSITY OF CIAL NJVERSITY OF UNIVERSITY OF NCING LIVERP 毛我S1T ER...

A: Calculated vertical force P and normal reaction force N on the tire.

Q: NOTE: ANSWER ALL QUISTIONS Q1) Answer the following questions. (C..-- 1- Explain the selection of en...

A: 1. 1. The selection of a specific material for a particular use depends on various factors like oper...

Q: Spur gear train is used to transmit the power of 2kW from input gear A rotating at 120 rpm to output...

Q: nsions shown is hinged at its top at A. The gate rests on a frictionless surface at B. a. Determine...

A: given:

Q: What container has the greatest pressure at the point indicated? Which point experiences the least...

A: 1 => D -) It's having a greatest pressure. 2 => Actually values not mentioned in given questio...

Q: In a pumping system handling water, the surface level of water in the open sanction tank is 3m below...

Q: How to convert an audio frequency of 89 dB to Hz

A: Given Data : 89 dB Hz

Q: 5, 0.06, readings

Q: A standard vapor-compression cycle developing 50kW of refrigeration using R22 operates with a conden...

A: Dear student, According to the guidelines I am allowed to answer only three sub-p...

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

Assume MN= 76 lb

The figure below is a bracket which fastened by a bolts
with a diameter of 0.5 inch. Compute the corresponding
shear stresses. Assume single shear.
Note: Round off your answer in two decimal places.
45°
MN Ib
12 in.
A O
36 in.-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
A simply supported wood beam is subjected to point load P at mid-span. The stresses on element C are known to be ??x=-92 psi and txy= -7 psi. Find the principal stresses on the element and show them on a sketch of a properly oriented clement.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A traffic light and signal pole is subjected to the weight of each traffic signal We = 45 lb and the weight of the road lamp WL= 55 lb. The pole is fixed at the base. Find the principal normal stresses and the maximum shear stress on element B located 19 ft above the base (see figure). Assume that the weight of the pole and lateral arms is included in the signal and lamp weights