The Figure below shown a pipe with a diameter of 5 cm connected to a reservoir and delivered a totaldischarge of 60 m'h. Detemine the type of flow if turbulent or laminar. What is the value of the pressure atpoint 1? Assume that u= 0.001 kg/m.s and f= 0.0136.30mQ- 60m/h? Pa80m10m60m

Name: The Figure below shown a pipe with a diameter of 5 cm connected to a
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The Figure below shown a pipe with a diameter of 5 cm connected to a reservoir and delivered a totaldischarge of 60 m'h. Detemine the type of flow if turbulent or laminar. What is the value of the pressure atpoint 1? Assume that u= 0.001 kg/m.s and

Answered: Image /qna-images/answer/82121be0-56d8-4f79-8bf3-1fbbb2bec454.jpg

Engineering

Mechanical Engineering

The Figure below shown a pipe with a diameter of 5 cm connected to a reservoir and delivered a total discharge of 60 m'h. Determine the type of flow if turbulent or laminar. What is the value of the pressure at point 1? Assume that u= 0.001 kg/m.s and f 0.0136. 30m ? Pa 80m 10m 60m

The Figure below shown a pipe with a diameter of 5 cm connected to a reservoir and delivered a total discharge of 60 m'h. Determine the type of flow if turbulent or laminar. What is the value of the pressure at point 1? Assume that u= 0.001 kg/m.s and f 0.0136. 30m ? Pa 80m 10m 60m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Select duct sizes for the rectangular duct system shown in the Figure, using the equal friction method. The total pressure available for the duct system is 0.12 in. wg (30 Pa), and the loss in total pressure for each diffuser at the specified flow rate is 0.02 in. wg (5 Pa). Assume the velocity in mean duct 600 fpm. 150 che 25 Boo ae und torectang a5On e S. 150 ct 0.095 mi 071 15m
A pump delivers water from a tank (A)X water surface elevation-110m) to tank B (water surface elevation= 170m). The suction pipe is 45m long and 35cm in diameter the delivered pipe is 950m long 25cm in diameter. Loss head due to friction hf1 = 5m and h2 3m If the piping are from pipe(1)= steel sheet metal pipe(2)= stainless – steel Calculate the following i) ii) The discharge in the pipeline The power delivered by the pump.
oil CM=0-08372 Pa.s, S6= 0.843 is flowing from the Upper to lower reservoir at a rate of o028/s through a 15 cm & smooth pipe. Calculate the elevation of oil and the upper reservoir. S. pipe o= 15cm El OIL Gom Kc=05 go bénd El 130m oil 130m
Length and dia. Of pipe 1 are 2000m and 1m while the second pipe is 2000m and dia. Of 0.8m .Find the rate flow of each pipe if the total flow rate in the main pipe is 0.3 m3/s. the coefficient friction of each pipe is same and equal to 0.05. Ans.Q1= 1.906 m3/s , Q2=1.094m3/s Ex. A pipe of dia.=20cm and length 2000m is connects two reservoir having difference of water levels as 20m determine the discharge through pipe. If an additional pipe of diameter 20cm and length 1200 m is attached to the last 1200m length of the existing pipe, find the increase in the discharge. f=0.015 neglect minor losses. Ans.Q= 0.0254 m3/s , increase to discharge 0.0088m3/s Ex. Pipe of L=4000m and dia.=0.6m as shown in fig. At a distance of 1000m from the upper reservoir , a small pipe is connected to the pipe line. The water can be taken from the small pipe. Find discharge to the lower reservoir a- No water is taken from the small pipe b-100 liter/sec of water is taken from small pipe. f30.005 neglect minor…
Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as shown in the figure below.. Note that p°- 1.013*105 Pa Calculate the absolute pressure (Pa). Density: Pwater = 1000 kg/m Pail = 800 kg/m Pand = 200 kg/m P. h3=12 cm hg al2cm oIL Pa h25 cm ng = 6 cm %3D Sand water
Consider an oil flow of 12 m³/h in a long, straight and smooth pipe with diameter of 7 cm. What is the pressure loss per meter? Oil absol viscosity is 0,1 kg/ms and density is 900 kg/m³. Friction factor for laminar flow can be calculated from 64 f=t Round off the answer to an integer in Pa/m, but enter the answer without the unit. 0.1 0.09 0.08 0.07 0.06- 0.05 0.04- 0.03 0.025- 0.00 Lamitin THW 1 Transition ang Wholly turbulent flow Suth 0.05 0.04 0.03 0.02 0.015 0.01 0.008 0.006 0.004 0.002 0.001 0.0008 0,0004 0.0002 00001 300006 000001 D
Q.10) Water, is pumped between two reservoir at 0.005 m3/s through a 100 m of 2 in diameter pipe and several minor losses, as shown in figure. The roughness is ε=0.02 mm. Compute the pump head required to maintain the flow. Z1-6 m Sharp Entrance K=0.8 Gate Valve K= 0.2 Standard Elbow K=0.9 Sharp Exit K= 0.5 Gate Valve K= 0.2 Long radius elbow K=0.2 Z2-30 m
This is a fluid machine question. Water reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 98.08 kPa is maintained in the summit water discharge is 30 m above the reservoir. The quantity pumped is 0.50 m3/s. rrictional losses in the discharge and suction pipe of the pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm, what amount of energy must be furnished by the pump in kW?
VIN/20 water is pumped from a * large tanken to a second tand 2 through a pipe system, as shown in the figure. The pump is developing on the flow. For a steady flow of 140 L/s, what must be the pressure PB in the air trapped above the water 20 kw . tank 2. The vertical 7.S pipe 40m Long. Фра=2 кра Solution Power: 20 kw Q = 140 L/S 150m 45m PB = ? h = 40m d=200mm = 0.2m M= 0.998X13 Nism OPB 6m B. E 1.42 ·lum water D=200 2 2 9u
A pump is being used to transport a liquid food product (density = 1000 Kg/m3, viscosity= 1.2 x 10 -3 Pa-s) from a holding tank to a filling machine at a mass flow rate of 2 Kg/s. The liquid level at the holding tank is 5 m above the pump, and the filling machine is 10 m above the pump. There is 100 m of 2 inch nominal diameter sanitary pipeline (assume: commercial steel) between the holding tank and the filling machine with one open glove valve and three medium sweep 90oelbows in the system. Determine the theoretical power requirement of the pump if the efficiency is 75%. Answer: 234 Watts. Show the solution.
Question 5: The pump shown below delivers a head of 50 m to the water through 30 cm diameter with pipe length 500 m. If the head loss is given by determine. L V² 0.02 / 1. The flow rate (Q) through the system in m³/s 2. The input power (Pi) required to supply the pump if the efficiency=75% 2 40 m L w **** AVB
A tanker carrying tolueneis unloaded to an onshore storage tank using the ship’s pumps. The pipeline is 225-mm inside diameter and 900-m long (200-m long suction line, 700-m long discharged line). Miscellaneous losses due to fittings, valves, etc., amount to 100 equivalent pipe diameters at the suction side, and 500 equivalent pipe diameters at the discharged side. The maximum liquid level in the destination storage tank is 30 m above the lowest liquid level in the ship’s tanks. The ship’s tanks are nitrogen blanketed and maintained at an absolute pressure of 1.05 bar (1 bar = 10^5 Pa). The storage tank has a floating roof, which exerts an absolute pressure of 1.1 bar on the liquid. The ship must unload 1000 metric tons within 5 hours. Taking pump efficiency as 70%, (ρ = 874 kg/m3, μ = 0.62 cP, Pvapor = 0.037 atm absolute). Determine: Discharge head (m) and pressure (Pa) Actual pump power (kW) Available NPSH (m)