A pump is being used to transport a liquid food product (density = 1000 Kg/m3, viscosity= 1.2 x 10 -3 Pa-s) from a holding tank to a filling machine at a mass flow rate of 2 Kg/s. The liquid level at the holding tank is 5 m above the pump, and the filling machine is 10 m above the pump. There is 100 m of 2 inch nominal diameter sanitary pipeline (assume: commercial steel) between the holding tank and the filling machine with one open glove valve and three medium sweep 90oelbows in the system. Determine the theoretical power requirement of the pump if the efficiency is 75%. Answer: 234 Watts. Show the solut

Q: A pump is being used to transport a liquid food product (p = 1250 kg/m³, µ = 1.5 cP) from a holding…

A: Given, Density of liquid, ρ=1250 kg/m3Viscosity, μ=1.5 cp,Mass flow rate=2.5 kg/sec,Diameter of the…

Q: [2] A cheap radial-vaned centrifugal fan is required to provide a supply of pressurised air to a…

A: Given: V=0.3 m3/sZ=30∆h=8 cm = 0.08 mη=0.8

Q: Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to…

A:

Q: An air-water manometer is connected to either side of a 0.20 m orifice in a 0.30 m water pipe. If…

A:

Q: Select duct sizes for the rectangular duct system shown in the Figure, using the equal friction…

A: Given DataL=6mTotal pressure of the Duct=30PaPressure of Each Diffuser=5Pa Given System

Q: Oil (SG oil = 0.95) flows at 200 L/s through a 200mm diameter pipe, 500m long. Friction factor is…

A: Discharge = 200 L/sor Q=0.2 m3/sdiameter (d) =200mm or d=0.2mlength of the pipe (L) =500mfriction…

Q: HW Question : The tank-pipe system is to deliver at least 12.5 m3/h of water at 20°C to the…

A: The maximum roughness height ε allowable for the pipe is 0.44344 mm.

Q: t the gasoline transfer facility (ρᵣₑₗ=0,75) from the pond of  storage to consumption, you want to…

A: The power required to operate a pump between 2 points in the system can be obtained by using the…

Q: Examples: Example 1: Water (p= 62.36 lbm/ft° and µ= 7.536×10* lbm/ft-s) is flowing steadily in a 2…

A: Given,  Density , ρ = 62.36 lbm/ft3 Viscosity , μ= 7.536*10-4 lbm/ft.s Diameter of the pipe , D =2…

Q: 47. Water enters a system of parallel piping at a rate of 500 GPM. The pipes length and inside…

A:

Q: 6 cm-diameter commercial steel pipeline is used to transport water at 10⁰C from a reservoir to a…

A: In fluid mechanics, there are two types of flow laminar and turbulent. The flow which doesn't have…

Q: A pipeline connecting three tanks contains 10 standard long elbows, 5 globe valves that is half…

A:

Q: Suppose the pump as shown in the figure is operating at free delivery conditions. The pipe, both…

A:

Q: A pump is being used to transport a liquid food product (ρ = 1250 kg/m3, μ = 1.5 cP) from a holding…

A:

Q: (1) In Tinyland, houses are less than a foot high! The rainfall is laminar! The drainpipe shown in…

A:

Q: A petroleum product of viscosity 0.5 m Ns/m2 and density 700 kg/m3 is pumped througha pipe of 0.15 m…

A: Given Dataμ=0.5mNsm2P1=10.15PsiaP2=43.511Psiaρ=700kg/m3d=0.15

Q: 9.50. When 0.28 m³/s of water flow in a 0.3 m pipeline, 63 kW are lost in friction in 300 m of pipe.…

A:

Q: Water in an open tank is being pumped to a second tank with a flowrate and viscosity of 0.0624 lb…

A: Water flow rate, m=0.0624 lb/sWater viscosity, μ=6.72*10-4 lb/ft.sSuction side pipe, = 2 in,…

Q: We are interested in pumping biodiesel between two pumping stations that are 300 km apart, being the…

A:

Q: PROBLEM: Assume frictionless flow in a long, horizontal, conical pipe, where the diameter is 3.6 ft…

A: d1=3.6 ft since 1ft=0.3048 md1=1.097 md2=2.4 ftd2=.7315 mQ˙=95 cfs since 1cfs = 0.0283 m3secQ˙=…

Q: A 1.0 m radius cylindrical industrial tank filled with viscous oil to a level at a height h from its…

A: Given: Radius of tube = 0.2 m Radius of tank = 1.0 m speed of oil in tube = 0.35 m/s

Q: The figure shows a system for delivering lawn fertilizer in liquid form. The nozzle on the end of…

A:

Q: 6) Through the pipeline system in the figure, calculate the flow velocity and flow rate at B, if Pa…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: In a pipe with constant flow rate, if diameter of pipe is halved and length of pipe is doubled, then…

A:

Q: 3. A 100 m length of smooth horizontal pipe is attached to a large reservoir. What depth d, must be…

A:

Q: . in a section of horizontal piper with a diameter of 3cm the pressure is 5.21 kpa and water is…

A: As per given guideline we have slove 1 question if you need please repost again As per given…

Q: The system in Fig. below consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged…

A:

Q: A vertical pipe of 2.5 m diameter and 25 m length has a pressure head of 6.5 m of water at the upper…

A:

Q: Water flows from a large reservoir down a straight pipe of 2500 m length and 0.2 m diameter. At the…

A: L=2500 md=0.2 mH=500 mf=0.03k=1.0

Q: A fluid is pumped at a rate of 0.00156 m /s through a 0.025-m-diameter pipe to fill a water tank as…

A:

Q: A pump delivers water from a tank (A)X water surface elevation=D110m) to tank B (water surface…

A:

Q: The pressure drop, due to the head and minor losses, between the two ends of a horizontal pipeline…

A:

Q: Oil (Density = 860kg/m³, Dynamic viscosity = 0.002 Pa.s) flows through a pipe of 100mm diameter with…

A:

Q: A pump is used to take water out of a large lake and deliver it to a farm to be used for irrigation.…

A: Given data: Q=100 L/sd=150 mm Need to determine the pressure in the suction side.

Q: r=20mm, the friction factor , the shear stress at pipe wall and the head loss per meter of the pipe…

A: Given: s=0.85 ρ=850 kg/m3ν=1.8×10-5 m2/sD=100 mmQ=0.50 L/sTo determine:Center line velocityvelocity…

Q: Problem 5: A fluid flows by gravity down an 8-cm galvanized ironpipe. The pressures at the higher…

A: Given data as per question

Q: An engine cooling system consists of the following components and associated losses; Engine Block…

A: Answer: The total head loss associated with piping system is 27.79 m. Hence, the correct answer is…

Q: a steel pipe has an inside diameter of 25 mm, is 20 m long, and carries 10 deg Celcius water at a…

A: Given data: f=0.0259Q=4.5 m3/h=1.25×10-3 m3/sL=20 md=25 mm=0.025 mPi=70 kPa Need to determine the…

Q: flow rate Q in liters per minute at maximum efficiency are estimated to be

A: Given data; Condition-1                        Condition-2  N1=500 rpm…

Q: Heavy fuel oil is pumped at a flow rate of 88 L/s through a new steel pipe. What diameter of the…

A:

Q: Oil of density 950 kg/m³ and viscosity 1E-2 Pas is to be pumped 10 through a pipeline and the…

A:

Q: A pipe is being designed to carry a fluid at a pressure of 193 MPa. In order to allow sufficien…

A:

Q: Q1. The figure below shows a hot water tank, with a pumping arrangement to continuously circulate…

A:

Q: A fluid is pumped at a rate of 0.00156 m3/s through a 0.025-m-diameter pipe to fill a water tank as…

A:

Q: A liquid food (density = 1200 kg/m³, viscosity = 0.07 Pa s) is to be pumped from an open constant…

A:

Q: A pump is being used to transport a liquid food product (density p=1000kg/m^3, viscosity 0.001 Pa s)…

A:

Q: We are interested in pumping biodiesel between two pumping stations that are 300 km apart, being the…

A: Given,   Density of biodiesel,ρ=874.6kg/m3Kinematic viscosity of biodieselv=4.09×10-6…

Q: n the diesel oil transfer facility (ρ rel = 0.85), from the storage tank to the consumption tank, we…

A: The power required by the pump can be calculated by the formula given below as- P=ρgQhL where Q is…

Q: Galvanized iron pipes with a roughness height of 0.40 cm are used to deliver water from reservoir A…

A: