Moving to another question will save this response.Question 4The figure below shows an undersea structure with a shape that can be approximated as one half of a cylinder.Given:H = 38 mL = 37 mD = 3 mSeawater, sg = 1.04#of섬Seawater-L-Estimate the total surface force (kN) acting on this structure.Express your answer in whole number.Moving to another question will save this response.7B

Answered: Image /qna-images/answer/682e39cb-d6ae-464f-83d7-0e484c07bed6.jpg

The figure below shows an undersea structure with a shape that can be approximated as one half of a cylinder. Given: H = 38 m L = 37 m D=3m Seawater, sg = 1.04 Seawater D Estimate the total surface force (kN) acting on this structure. Express your answer in whole number.

The figure below shows an undersea structure with a shape that can be approximated as one half of a cylinder. Given: H = 38 m L = 37 m D=3m Seawater, sg = 1.04 Seawater D Estimate the total surface force (kN) acting on this structure. Express your answer in whole number.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.9P

See similar textbooks

Related questions

Q: Following bearings were observed while running a closed traverse. Correct the bearing for local…

Q: Calculate the hindered settling velocity of certain solid particles (S.G. = 2.701), having a…

Q: Find maximum principal stress experienced on the shaft?

A: Given data, Shaft diameter,d= 80 mm Axial stress,σ=30 MPaTorque,T= 50 KN-mCalculate maximum…

Q: 3 m w (N/m) ↓↓↓↓↓↓↓ 3m Figure 3 1.5 m

A: According to given dataThe solution is given below

Q: The cast iron bearing seat in the picture is bolted to the steel beam of the ceiling bracket and…

A: Solution: (a) For ISO 8.8 bolts, minimum proof strength, Sp = 600 MPa For permanent joints and…

Q: Three cables intersect at B in order to stabilize a telephone pole, as shown in the figure. The unit…

A: Given :

Q: An aluminium alloy (density 2600 kg/m³) casting is to be produced. A cylindrical hole of 100 mm…

Q: 20kN A 40KN BY C 40kN D 20KN 40kN E G 6 panels @3.0 m = 18.0 m 40KN K 20kN 6.0 m

A: To filorces in members BD,DE & EG using method of sections.

Q: Draw the cross sections and compute V. Two level sections of 40-m stations with center heights of…

Q: A simply supported beam with spans of LAB = 15 ft and LBC = 45 ft supports loads of w = 3.0 kips/ft…

A: Given data

Q: 5 5a 5b 5c Alaterally supported beam was designed for flexure. The beam is safe for shear &…

Q: A wooden triangle body (s=0.80) is placed in water in the position indicated in the figure. if the…

Q: 6 6a 6b 6c Alaterally supported beam was designed for flexure. The beam is safe for shear &…

A: For 6x20 Sx = 220x103 mm3 Md(design moment) = fyxSx So, flexure strength depends on yield…

Q: A thick cylindrical pressure vessel of inner diameter D, and outer diameter D is subjected to an…

A: Given- Inner dia DiOuter dia DoInternal fluid pressure =pcircumferential tensile stress=py

Q: ches in di

A: Using equation :HL=flv22gdv=QA=2π45122

Q: Compute the combine stress on a solid round bar with a diameter of 3 cm. The load of 75,000 KN is…

Q: Q5/ In the plan below there is a conventional U shape stair, the distance between slabs is 3.00 m.…

A: Number of steps Riser height Tread width

Q: solve the stresses in members DF,DG and EG using method of sections

A: Given data Using method of section

Q: A rigid horizontal bar (Weight = 20 kips) is supported by two (2) square aluminum columns as shown.…

Q: Determine the magnitude of the pin force at A. Assume W = 590 lb, a = 2.9 ft, b = 2.0 ft, r = 6 in.…

Q: Determine the x-coordinate of the centroid of the shaded area by integration. y 28 27 Answer: T 34

Q: the velocity of the fluid (in m/s) at a

A: Given data, An incompressible homogenous fluid is flowing steadily in a varable, diameter pipe hving…

Q: Problem Water is pumped through a vertical steel pipe to an elevated tank. D = 10 cm, P₁= 1.6 MPa, L…

A: Given data:- Diameter of pipe, D=10 cm Length of the pipe, L=80 m Pressure, P1=1.6 MPa=1.6×106 N/m2…

Q: Please

A: As there are multiple questions posted, according to the guidelines, only the first three are being…

Q: Determine the angle of twist at the free end A of the shaft

Q: A long rod of uniform rectangular section with thickness t, originally straight, is bent into the…

A: given- rectangular thickness=tdisplacement=d at mid spanspan length =Llongitudinal surface strain is…

Q: Determine the kind (direction) and amount (magnitude) of stress in each member of the trusses loaded…

Q: Explain two methods discussed in class for finding the area of irregular shapes.

A: The irregular shapes are those shapes that do not have equal sides or equal angles. The area of an…

Q: A 502-Mg train accelerates uniformly from rest to a speed of 97 km/h in 54 s. After reaching this…

A: Newton law's of motion: These law describes the relationship between the object and forces acted…

Q: Consider the tank shown in the figure. The gate is rectangular in shape with width into the paper of…

Q: 5. Given the beam AB as shown, find the force F2 and its moment arm, d. FA= 50 N F₂ 1.m.. - F₁= 15 N…

A: Given Data Force at point AFA=50 NF1=15 NF3=30 NThe span lengthL=1.8 mWe are supposed to calculate…

Q: Situation 9: From the figure shown, two spheres having equal weights of 360 N each is placed on top…

A: Given,

Q: A Simple Curve connects to Tangents AB and BC with bearings N85d30'E and S68d30'E respectively. If…

Q: Situation 3: If 0 = 30° and T = 6 kN, determine the magnitude of the resultant force acting on the…

Q: Based on the following specification, analyze the suitability of a section with size of 50 mm x 250…

A: Analysis of Beam : Determination of analysis of beam is carried out to find out the structural…

Q: What is the equivalent point load for the linear varying distributed load shown below? Hint: Convert…

A: Given :

Q: A composite beam is made of two brass [E = 99 GPa] plates bonded to an aluminum [E = 63 GPa] bar, as…

A: Given data A composite beam is made of two brass [E = 99 GPa] plates bonded to an aluminum [E = 63…

Q: shear stress in the wall?

A: Given data, Inner radius of a cylindrical tank is, r=12 mwall thickness,t= 75 mmGauge…

Q: A rectangular irrigation canal 3 m wide carries water with a discharge of 6 m^3/s. A rectangular…

A: According to given dataThe height of the rectangular weir if it is suppressed will be H= 1.05m…

Q: magnitude of the velocity.

A: Given data, Velocity,V= 35 m/sin the horizontal direction Where,Wheel radius is = rCalculate…

Q: Sustainable materials for road maintenance can be also defined as a way to use a resource so that…

A: (i) Two (2) types of sustainable materials that can be applied for road maintenance activities are-…

Q: Prob-1 A room is heated with a 1500 W electric heater. How much power can be saved if a heat pump…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

Q: for the given truss a. Draw the free-body diagram without the zero-force members. b. Use the method…

A: Truss: Truss is a pin joint structure subjected to loading only on joint and there is only one force…

Q: (a) Calculate the thing of protection of the block against sliding if the density of the rock is…

Q: The maximum bending stress (in MPa)

A: Given data, Simply supported beam having,width,b= 100 mm=0.1 mheight,h= 200 mm=0.2 mlength,l= 4…

Q: External support reactions: RA= RC = RF = KN KN KN The shear and moment at point B are The moment at…

Q: Prob. 4.3-13. The solid circular shaft in Fig. P4.3-13 is sub- jected to a distributed external…

Q: A solid circular shaft of diameter 60mm is subjected to an axial stress of 20 MPa. It is further…

A: Given data: diameter = 60 mm Axial stress 20 MPa torque = 7 kN.m

Q: 1. 1 For the beam shown below, (a) Draw the V-Diagram (b) Draw the M-Diagram (c) Find the largest…

A: Solution: (a) Shear force diagram: VC=0VB=1000lbVA=1000 lb

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Need answer ASAP. Please be detailed and clear with your solution. V. A wooden buoy of specific gravity 0.75 floats in a liquid having a specific gravity of 0.85.1) Evaluate the percentage of the volume of the buoy above the liquid surface to the total volume of the buoy. * 2) If the volume above the liquid is 0.045 cubic meters, estimate the weight of the buoy, in kN. 3) What vertical force, in kN, applied to the buoy to fully submerge it? *
Need answer ASAP. Please be detailed and clear with your solution. VI. A cylindrical buoy 2 m in diameter and 1.5 m in height weighs 12 kN and floats in salt water of density 1020 kg/m³. Center of gravity of buoy is 0.65 m above the bottom. If a load of 2 kN is place on its top symmetrically. 1) Find the height that the buoy sink in salt water, in meters. * Find the maximum height, in meters, of the center of gravity of this 2 kN load above the bottom if the buoy is to remain in stable equilibrium. Show figure. *
An orifice on the side of a tank discharges water under a head of 9 ft. if the diameter of the orifice is 2”, the coefficient of contraction is 0.63, and the head lost is 0.80 ft, determine the discharge, CV and CD. Pls show also the figure/diagram
Answer the following questions!a. What is the definition of Archie's Equation?b. What is Archie's Law of Saturation Equation?
Give me all three right solutions Note: If you don't know the solution please leave it. Water is flowing at a depth of 5 ft with a velocity of 4 ft/s in a triangular channel with sideslopes of 3:1. A contraction occurs that decreases the sideslope to 2.5:1. a) Check for choking. b) Determine the downstream depth. If choking occurs, determine the adjusted upstream depth. c) Sketch the specific energy curve. Label all depths and corresponding specific energy.
High velocity water flows up an inclined plane, as shown in Figure 5 .1 What are the two possible depth of flow at section 2? Neglect al losses.
B. How the location of the start of the hydraulic jump is determined? Assume the necessary parameters to explain your answer.
A vertical cylinder having a circular base of radius r and a height of 12 m is filled with water at the rate of 1 m^3/min. if the depth of water in the cylinder at the vertical position is 3 m. what would be the resulting depth when the cylinder is in the horizontal position? a. 0.60r b. 0.40r c. 0.30r d. 0.50r
A cylindrical vessel with a height of 4.3m and diameter 2.9m has an orifice located at the bottom surface. If the water level in the vessel is to be emptied from a 3.6m depth, how long did it take for the vessel to be empty (in min)? Assume the orifice to have a diameter of 55mm and c = 0.62.
A 600 mm diameter horizontal pipe with a length of 1500m and C=120. the pressure gage attached downstream of the pipe reads 16kpa and another gage is attached upstream of the pipe reads 30kPa. If another gage is attached between the ends of the pipe. What is the total head loss?
3. The 500 mm diameter pipe conveys treated water to supply a municipality with a demand of 40 MLD. Determine the head loss in meter if the length of the pipe is 10 km considering that (a) friction factor f is 0.018, (b) Hazen-William coefficient C is 90, and (c) Mannings coefficient n is 0.015.
A pressure gage in kPa scale is installed in an underwater submarine. What should be thereading in the gage if the submarine is 100 meters below the surface of the ocean (SG =1.03)? What is the depth of the submarine if the gage reads 1000 kPa?