The figure shows a rotating geared system. A torque of 3N is applied to an input gear in order to accelerate a flywheel at 0.1 rad/s2. The input gear has 11 teeth, and the output gear has 99 teeth. What is the flywheel's inertia? T= 3N O 0 0 0 0 Input gear 11 teeth Output gear 99 teeth 270 kgm2 57 kgm2 2.7 kgm² Don't Know 27 kgm2 Flywheel 0.1 rad/s²

The figure shows a rotating geared system. A torque of 3N is applied to an input gear in order to accelerate a flywheel at 0.1 rad/s2. The input gear has 11 teeth, and the output gear has 99 teeth. What is the flywheel's inertia? T= 3N O 0 0 0 0 Input gear 11 teeth Output gear 99 teeth 270 kgm2 57 kgm2 2.7 kgm² Don't Know 27 kgm2 Flywheel 0.1 rad/s²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The intermediate shaft of a two-stage gearbox is given in the figure. P = 4 kW power is transmitted at n = 150 rpm with the help of two helical gears on the shaft.The forces acting on the gears are given as Ft1 = 5092 N, Fr1 = 1972 N, Fa1 = 1853 N, Ft2 = 2546 N, Fr2 = 986 N, Fa2 = 926 N. Diameter of small helical gear d1 = 100 mm, largethe diameter of the gear is d2 = 200 mm. Shaft material yield strength 335 MPa, tensile strength 600 MPa, Kç = 1.95, ka = 0.895, kb = 0.90 and safety coefficient = 1.4now that
Number of teeth of gears z1: 22 Tooth numbers of gears z2: 90 Tooth numbers of gears z3: 23 Tooth numbers of gears z4: 77 The efficiency of gear pairs ηd: 0,96 The efficiency of the bearing pairs ηr: 0,94 Electric motor speed: 2050 Belt speed (v) (m / s): 1.30 Required force for belt movement (N) g: 2200 a) Find the diameter of the drum? b) Find the required motor power?
In the fabric dye-printing system given in the figure, the motion is transmitted from the electric motor to the drum of the machine. There is a two-stage reducer in between. Number of teeth of gears z1=17; z2=85; z3=18; z4=72; The efficiency of a pair of gears is given as na=0.97 and the efficiency of each of the gearbox shafts and lower bearing pairs to the drum bearing is given as n=0.97. The diameter of the drum will be D=200 mm, the fabric speed will be v=1 m/s and the pulling force required to activate the band will be taken as F-2000 N. a) Find the number of revolutions of the engine. b) Find the required engine power.
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 84cm and 35cm respectively. If driven shaft runs with 10 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 6mm
In the design in the figure, a force of Fn=45992 N acts in the vertical plane on a machine element with a diameter of D=200 mm on the shaft resting on the A and B bearings. If the angle made by this force with the horizontal is b=40o, find the life of the 6210 coded Deep Ball bearing to be used in the B bearing, in hours. Number of revolutions = 30 rpm. 1-) The diameter of the machine element on which the force acts will be taken into account in the calculation of bearing forces (That is, it will be assumed that the Fn force AFFECTS THE GROUND shown in the figure, NOT the axis of the shaft). 2-) Pi number will be taken as 3.14.
A shaft made of steel receives 7.5 kW power at 1500 rpm. A pulley mounted on the shaft as shown in Fig. has ratio of belt tensions 4. The gear forces are as follows: Ft = 1590 N; Fr=580 N Designe the shaft diameter by maximum shear stress theory. The shaft material has the following properties: Ultimate tensile strength = 720 MPa: Yield strength = 380 MPa: Factor of safety = 1.5
What are the maximum, minimum, and average power values for the shaft shown in the figure below if the shaft speed is 50 rpm, l = 14 cm, a = 4 cm, b = 12 cm, P = 750 N, Tmin = -200 N-m, Tmax = 400 N-m.
A pair of helical gears transmit 15 KW power and the pinion is rotating at 1000 rpm. The helix angle is 0.50 radians and the normal pressure angle is 0.35 radians. The pitch diameter of the pinion is 70 mm and the pitch diameter of the gear is 210 mm. Determine the tangential, radial, and axial forces between the gear teeth.
The motor shown in the figure supplies 16.5 kW at 1540 rpm at A. Shafts (1) and (2) are each solid 28 mm diameter shafts. Shaft (1) is made of an aluminum alloy [ G=26 GPa], and shaft (2) is made of bronze [ G=45 GPa]. The shaft lengths are L1=3.3m and L2=2.9m, respectively. Gear B has 56 teeth, and gear C has 97 teeth. The bearings shown permit free rotation of the shafts. Determine: the rotation angle of gear D with respect to flange A. [Answer φD/A = 0.314 rad]
In the pulley system shown in the figure, while the P gear rotates in the direction of 1 with its angular velocity, find the direction and angular velocity values of the other gears. Hint: The speed of the gears is equal at the point of contact. The speed of a belt is the same at all points.( w=3 rad/s , rk=0.8m ,rL=0.2 m ,rM=0.2m, rN=0.5m rP=0.4m rR=0.4m
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) Power transmission =60 kW,(ii) Shaft speed = 160 rpm,(iii)The angle of twist / m length = 1.1º(iv)Maximum twisting moment is 30% greater than its mean. (v) Take Modulus of rigidity as 105 Gpa. (i) Mean torque of the shaft (unit in Nm) = (ii)Maximum torque of shaft (unit in Nm) = (iii) The diameter of the shaft (unit in mm) = iv) Maximum shear stress in the shaft (Unit in MPa) is
A gear box has an input speed of 1500 rev/min clockwise and an output speed of 300 rev/min anticlockwise. The input power is 20kW and the efficiency is 70%. Determine the followings. a). The velocity ratio(or geo ratio) b). The input torque c). The output power d). The output torque e). The holding torque