Answered: The figure shows an angle beam composed…

The figure shows an angle beam composed of two bars with thickness 69 mm. Locate the centroid (Y-bar, in mm.), d = 21 mm. from the topmost. Given: A = 447 mm. B = 402 mm.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.60P: Determine Iu for the inverted T-section shown. Note that the section is symmetric about the y-axis.

See similar textbooks

Related questions

Q: Which of the following need NOT be reflected in a sketch when using the Linear Momentum Equation? a.…

A: For part 3Given Dtatala=1.5mspan=9mVa=7.5m/sScale ratio=1/10 ***As per company policy we are…

Q: 18.13 A rotary compressor is used to supercharge a petrol engine. The static pressure ratio across…

A: We have a rotary compressor for supercharging a gasoline engine. The rotor's static pressure ratio…

Q: Question 3 Three forces act on the lever arm, as shown in Figure 3. Determine the magnitude of the…

A: The resultant moment of these forces about point P: 2.25 N•m

Q: Determine the force in each member of the Pratt roof truss shown in Figure 1-94. 10 kN 10 kN 10 kN B…

Q: Which of the following is the correct statement? a. Irreversible engines have maximum efficiency…

A: 1 Irreversible engines have maximum efficiency. In the irreversible engine, there are various types…

Q: Which is not a cause of detonation? Wrong ignition timing Allowing the engine to overheat Fuel/air…

Q: A tianium disk (roe 107 CPa, Poisson's ratio = 0,34) precisely 8 mm thick by 30 mm diameter is used…

Q: Problem 6: Draw the shear and moment diagrams for the beam. 10 kN 10 kN 12 kN - m B 2 m -2 m- 2 m 2…

Q: The three concentrated load is supported by a T beam shown in figure. Determine the maximum value of…

Q: A power plant running on the Ideal Rankine cycle heats water at a pressure of 13 MPa. The heating…

Q: Steam turbine receives 400000 kg/hr of steam throttled in actual reheat Rankine cycle with two…

Q: a. Which shows the Rotation and Translation Diagram for the problem below? B A Vo VO/A - VA Vo VO/A…

Q: The record of highest temperature in eight specific states is given below. 112, 100, 127, 120, 134,…

A: The record of highest temperature in eight specific states 112, 100, 127, 120, 134, 118, 105, 110

Q: A hole is to be punched out of a plate having a shearing strength of 50 ksi. The compressive stress…

A: following is the solution

Q: An ideal incomplete-expansion cycle uses steam generated at 1.85 MPa. Release condition is dry and…

Q: Calculate the quantity of heat conducted per minute through a duralumin circular disc 127 mm…

A: Given data as per the question Diameter of the disc =127 mm The thickness of the disk = 19 mm…

Q: 5. Determine the force in members AB, AC, CE, DF, and EG of the cantilever truss shown in Figure…

Q: QUESTION 37 Which of the following are true for the limitations and impracticalities of the…

Q: A shaft capable of transmitting 50 kW of power will spin at 100 revolutions per minute. The maximum…

A: Given Power, P = 50 kW Speed, N =10 0 rpm Length, l = 3 m Angle = 1.5 degree Find Diameter,…

Q: A single block brake, as shown, requires an operating force of 700 N. If the coefficient of friction…

Q: A flat circular steel plate has a diameter of 50 cm and a mass of 60 kg. Calculate the thickness…

Q: Determine the reaction components for the rigid body in the figure. A *** B '6' 10 ft 4 √₁2m 12 f…

Q: For the given vectors V₁ and V₂, determine V₁ + V₂, V₁ + V2, V₁ - V2, V₁ X V2, V₁ V₂. Consider the…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: While walking along the beach, a person sees a dented aluminum can whose mass is 100 grams. The can…

A: Calculate change in entropy of universe.

Q: A spark-ignition engine has a compression ratio of 10:1. The total intake volume of the cylinders is…

Q: A highway is designed for traffic moving at 65 mph. Along a certain portion of the highway, the…

A: The free body diagram :

Q: We are going to add a low pressure turbine (5-6) to the system we just analyzed. Before going into…

A: Given that, At P3=15 MPa and T3=400 °C,h3=2975.548 kJ/kg,At P4=2 MPa,hg=h4=2798.3884 kJ/kg,At P5=2…

Q: In each case, draw the estimated elastic curve: 4 m- 8 kN.m 2 kN/m 8 kN 4 kN

Q: 2 An oil of viscosity 10 poise flows through a horizontal pipe (d = 80 mm). If pressure drop in 100…

Q: 6-22* A pipe strut BC is loaded and supported as shown in Fig. P6-22. Determine (a) The reactions at…

A: The free-body diagram of the system can be represented as below.

Q: what is the packaging materials, by product, waste, and common utilities used in distillery plant of…

Q: A car is travelling at vo = 21 m/s when a passing obstruction is sighted ahead at 120 m. The driver…

A: GivenV1=21m/sd1=120ma2=-4m/s2d2=-70ma3=3m/s2t3=15s

Q: "The speed of an object in motion is a positive quantity." Always true Sometimes true, it is…

A: Introduction: Speed is a scalar quantity that does not take into account direction, whereas velocity…

Q: Q1: Find the torque of the force 800 N in figure (1) about point 0.

Q: 1. In the cantilever truss shown in Figure 1-93, compute the force in members AC, BD, and DE. 1000…

A: FAC = -2000.000 lb (compression) FBD = 2309.401 lb (tension) FDE = - 1154.700 lb (compression)

Q: What is the acceleration of the object when (0 ≤t≤a a/d d/a a 0.5ad

Q: Fig shows a U-tube differential manometer connecting two pressure pipes at A and B. Pipe A contains…

A: ρ1= 1.5(1000)= 1500 kg/m3PA= 110 kN/m2= 110000 N/m2ρ2= 0.5(1000)= 500 kg/m3PB= 216 kN/m2= 216000…

Q: She releases her m= 4.6-kg, 220-mm diameter bowling ball with an initial velocity vG of 5 m/s and…

Q: A) Figure (2) shows the velocity distribution for flow of water between two parallel plates.…

Q: Fig shows a U-tube differential manometer connecting two pressure pipes at A and B. Pipe A contains…

A: GivenPA=110 kN/m2S.GA=1.5S.GB=0.5PB=216 kN/m2x=2.1my=1.1m

Q: The motion of an object is described by the v-t diagram shown below. V d MA t 0 a b Which of the…

Q: 1. A Brayton gas cycle produces a net load of 600 Btu/lb for an entrance temperature of 40°F and…

A: Given data Cycle : Brayton Gas cycle Net Load = 600 BTU/lb = 1395.60 kJ/kg Entrance temperature =…

Q: y decreasing the condenser pressure, the heat added increases; by increasing the boiler pressure,…

A: To state whether TRUE or FALSE

Q: Two uniform spheres are positioned as shown. Determine the gravitational force F which the titanium…

A: Calculate the masses of titanium and copper spheres. mt=ρtVt=ρt43πrt3=4500 kg/m343π0.030 m3=0.50894…

Q: Let the sponge relax on a flat surface and position the soap box as shown. Using your index finger,…

A: Introduction: Newton's first law states that unless acted on by an "unbalanced" force, an object…

Q: A refrigeration system is to be used to constantly maintain a space at -12°C in an industrial…

Q: Q2\ Determine the torsional stress of the cantilever shafts show in the figures below. 86= b T T 5…

Q: It is proposed to have carbon dioxide (CO2) gas pass through an uninsulated nozzle. The CO2 is to…

Q: The rocket motor shown in the figure is mounted on a test stand. (Test stand is not shown in the…

Q: Homework - 2 Q1: Find the torque of the force 800 N in figure (1) about point 0.

A: we will split the force in two parts horizontal and vertical and then find their respective moments

Question

The figure shows an angle beam composed of two bars with thickness 69 mm. Locate the centroid (Y-bar, in
mm.), d = 21 mm. from the topmost.
Given:
A = 447 mm.
B = 402 mm.
Id
A
*
*
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine Iu for the inverted T-section shown. Note that the section is symmetric about the y-axis.
Determine the second moment of area (Iyy) about the centroidal y-axis for a solid homogeneous beam section where the dimensions are b = 125 mm and d = 275 mm. Give your answer in m4 to 2 significant figures.
Determine the centroid ?̅ of the T-beam shown in Figure Q3
3.1. Determine the location of the centroid for the cross section shown below and draw a scaled sketch of the cross section, clearly showing the centroid and indicate it's distance from the selected origin. Start your calculations by setting an origin from the bottom, left most point on the cross section. 3.2 Calculate the second moments of areas about the centroid axes for the beam cross section
three plates are welded together to form the curved beam shown in the figure for M = 8kip * m. calculate effort in:a) point ab) point bc) the centroid of the cross section
determine the location of the centroid of a bent wire formed by the three segments shown in the Figure below. Indicate the centroid position of each segment.
Calculate the centroid of the composite shape AB= 85 C=1 BC = 12 only HANDWRITTEN answer needed ( NOT TYPED)
A block of stone is cut so that its cross‑section is a parallelogram. The width of the bottom side is ?=0.655 m, the height of the top of the block is ℎ=0.915 m, and the top right corner overhangs a distance ?oh=0.195 m from the bottom corner as shown. Assume that the block is of uniform density, so that the center of gravity of the block is located at the geometric center.
3.1)Determine the location of the centroid for the cross section shown in Figure 3 and draw a scaled sketch of the cross-section, clearly showing the centroid and indicate it's distance from the selected origin. (Start your calculations be setting an origin at the bottom, left most point on the cross section). 3,2)Calculate the second moment of areas about the centroidal axes for the beam cross-section from Figure 3.
For the beam I-section below, calculate the second moment of area about its centroidal x-axis (Ixxcentroid), where b1 = 10.50 mm, b2 = 2.50 mm, b3 = 38.50 mm, d1 = 1.50 mm, d2 = 36.50 mm and d3 = 12.50 mm. Give your answer in mm4 to two decimal places.
Calculate the centroid for the shaded portion of the figure as shown . Take b = 90 mm, b1=50 mm, b2 = 25 mm, h= 80 mm, h1=40 mm and R= 16 mm The Centroid in mm is Answer for part 1 The Centroid in mm is
For the composite beam section in Figure Q2b, calculate the second moment of area (Ixx) about its centroid x-axis.