The figure shows an approximate plot of stress (10° N/m2) versus strain for a thread that will break at a strain of 2.00. The thread has constant volume of 6.4x1014 m3. What is the maximum potential energy the thread can stored on the verge of breaking? 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 Strain O 2.95x10^-5J O 1.024x10^-4 J O 0.46x10^9J O 1.024x10^-13 J Stress (10° N/m2) 2.

The figure shows an approximate plot of stress (10° N/m2) versus strain for a thread that will break at a strain of 2.00. The thread has constant volume of 6.4x1014 m3. What is the maximum potential energy the thread can stored on the verge of breaking? 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 Strain O 2.95x10^-5J O 1.024x10^-4 J O 0.46x10^9J O 1.024x10^-13 J Stress (10° N/m2) 2.

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 81PQ: A horizontal, rigid bar of negligible weight is fixed against a vertical wall at one end and...

See similar textbooks

Similar questions

A horizontal, rigid bar of negligible weight is fixed against a vertical wall at one end and supported by a vertical string at the other end. The bar has a length of 50.0 cm and is used to support a hanging block of weight 400.0 N from a point 30.0 cm from the wall as shown in Figure P14.81. The string is made from a material with a tensile strength of 1.2 108 N/m2. Determine the largest diameter of the string for which it would still break. FIGURE P14.81
A spring 1.50 m long with force constant 475 N/m is hung from the ceiling of an elevator, and a block of mass 10.0 kg is attached to the bottom of the spring. (a) By how much is the spring stretched when the block is slowly lowered to its equilibrium point? (b) If the elevator subsequently accelerates upward at 2.00 m/s2, what is the position of the block, taking the equilibrium position found in part (a) as y = 0 and upwards as the positive y-direction. (c) If the elevator cable snaps during the acceleration, describe the subsequent motion of the block relative to the freely falling elevator. What is the amplitude of its motion?
A 1.25 m long cable has a diameter 3.50 mm with a Young’s Modulus, E, of 9.75 x 109 N/m2 . When the wire is placed under tension, it experiences a stress of 202.52 x 106 N/m2 , the length of the cable extends by 36.35 mm. Calculate the force that the cable experiences under tension and the strain energy density (U/V) due to deformation. Give your answers in newtons (N) to 2 decimal places for the force; and in joules per cubic metre (J/m3 ) for the strain energy density to 2 decimal places. Assume the cable is solid and the material is homogeneous.
Proof that the energy stored in the compact bone is given by E = AL0 (Sb) ^ 2 / 2γ. When Sb is bone stress. *
Your biceps muscle is attached to your elbow by the distal biceps tendon. An average adults tendon has a 6 mm by 3 mm rectangular cross-section and is 63 mm in length. A tendon has a Young’s modulus of 1.5x10^9 N/m^2. How much work must be done to stretch the length of the distal biceps tendon by 10%? Assume that the tendon is a linearly elastic material and that stretching does not alter it’s cross-section.
An ACL has an unloaded length of 3.8 cm and is subject to a tension stress that results in a 5% strain What length does the tendon stretch to as a direct result of the tendons strain? 1.) 3.99 cm 2.) 3.82 cm 3.) 2.82 cm 4.) 4.2 cm
the drawing shows a 150 kg crate hanging from one end of steel bar (S= 8.1 x10^10 n/m^2) The length of the bar is 0.428 m and its cross-sectional area is 7.94 x 10 ^-4 m^2. Neglect the weight of the bar itself and determine (a) the shear stress on the bar and (b) the vertical deflection deltaY of the right end of the bar.
Two rods of equal length 10.55 m2 anddiameter 11.7 cm2 are placed end to end. One rod is aluminum,the other is brass. If a compressive force of 8400 N is applied tothe rods, (a) how much does their combined length decrease?(b) Which of the rods changes its length by the greatest amount?Explain.
A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x 10^6 psi. When the same specimen is used in a tensile test, the modulus of elasticity is found to be 12.2 x 10^6 psi. Find Poisson’s ratio for the specimen.
A 20 g rectangle block of aluminium is 35 cm by 45 cm by 15 cm when unstressed. A force is applied tangentially to the upper surface causing a 4.7 cm displacement relative to the lower surface. The block is placed such that 35x45 comes on the lower and upper surface. Determine the shearing stress and shearing strain.
Between each pair of vertebrae in the spinal column is a cylindrical disc of cartilage. Suppose that such a particular disc of cartilage has a a radius of 3.118 cm (100cm = 1 meter) and a thickness of 6.877 mm (1000mm= 1meter). The shear modulus of cartilage is 1.2 × 107 N/m2. Suppose that a shearing force of magnitude 9 N is applied parallel to the top surface of the disc while the bottom surface remains fixed in place. How far does the top surface move relative to the bottom surface in microns (1 meter = 106 microns)?
A box with mass 178kg is supported by the cable system at B. Chord AB has a length of 1.2m and the force that develops in the chord is 3130N The horisontal distance between points A and C is 1.7m. Determine the force that develops in chord BC and the vertical height y and complete parts (a) and (b) below.