The following test results are obtained from a 3 -phase, 4800KW, 6600V, star connected, 2 pole, 50 Hz turbo alternator: With a field current of 125A, open circuit voltage is 8000V.With the same field current the short circuit current is 800A. Armature resistance is 0.218 ohm. Find the regulation of alternator on full load at a power factor of 0.8 leading.

The following test results are obtained from a 3 -phase, 4800KW, 6600V, star connected, 2 pole, 50 Hz turbo alternator: With a field current of 125A, open circuit voltage is 8000V.With the same field current the short circuit current is 800A. Armature resistance is 0.218 ohm. Find the regulation of alternator on full load at a power factor of 0.8 leading.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Kindly solve the problem with step by step complete solution. Also, show the given and formula used. Thanks! Find the synchronous impedance and reactance in alternator in which a given field current produces an armature current of 250A on short-circuit and the generated emf of 1500V on open circuit. The armature resistance is 2 ohms.
Find the synchronous impedance and reactance of an alternator in which a given field current produces an armature current of 300A on short-circuit and generated emf of 40V on an open-circuit. The armature resistance is 0.1 ohm. To what induced voltage must the alternator be excited if it is to deliver a load of 100A at pf of lagging, with a terminal voltage of 300V.
6. The relation between the field current and the armature current in an alternator with the armature short-circuited can be shown byA. a rated-current 80% pf saturation curve.B. a synchronous impedance curve.C. an open-circuit saturation curve.D. a zero-power-factor regulation curve.
Determine the efficiency of 1500kVA, 2300V, 3phase, Y-connected alternator, which operates at rated output with a power factor of 80%. The DC armature resistance at 70°C between terminals is 0.08Ω. The field takes 70A at a 120V from the exciter equipment. Friction and windage loss are 15kW, iron loss is 35kW and stray load losses is 1.5kW. Assume the effective armature winding resistance is 1.5 times the DC value.
Three phase 460 hp,415v,4pole,50hz induction motor is operating at Over voltage of 480v and reduced load of 80% of the rated value and draws a line current of 624.06A.The losses at these operating conditions are as follows .The stator conductor loss is 12.6 kw sketch the power flow diagram ,enter the known values and determine (a) rotor speed,(b) shaft output torque ,(c)developed mechanical torque in Nm (d)input power to the stator (f)The input power factor
Q2. For a 10 kW, 380V, three-phase, four-pole, 1200 r/min, delta-connected induction motor. Adopt a specific magnetic loading of 0.4712 Wb/m2 and a specific electric loading of 23000 ampere-conductors per metre. The motor has a full-load efficiency of 85% and a full-load power factor of 0.8. A square pole design may be assumed and the stator leakage impedance voltage drop may be ignored. Assume also that the winding is full-pitched and uniformly wound. To calculate the following design parameters (a) The approximate outer diameter and length of the rotor core (b) the air gap length of the motor (c) the turns per phase (d) the number of conductors per slot, if 3 slots per pole per phase are chosen
A 400V, 50Hz, 6-pole 3-phase asynchronous motor rotates 20Nm of constant load torque at 950rpm. If it is desired to rotate this load at 750 rpm mechanical speed;a) The synchronous speed of the motor,b) Supply frequency,c) Find the value of the supply voltage between phases?Note: The motor will be driven with V/F sbt because the load torque does not change.
A gas turbine, 2-pole, 3? synchronous generator rated at 200 MW is connected to the grid (presumed to be an infinite bus). The electrical operating frequency of the grid is 60 Hz, and the slope of the frequency-power curve for the generator is 15 MW/Hz. a. If the no-load setpoint for the generator is set to 63.5 Hz, how much active power will the generator provide to the grid? b. Neglecting system losses, what is the torque provided by the gas turbine? c. What would happen if the no-load setpoint for the generator is set to 59 Hz?
A 25-hp three-phase induction motor operates for a 440-Vrms (line-to-line) three phase source and draws a line current of 35 A rms at a power factor of 83 percent lagging under rated full load conditions. The full load speed is 1750 rpm. Under no load conditions the speed is 1797 rpm and the line current is 6.5 A rms at a power factor of 30 percent lagging. Find the power loss and efficiency with full load, the input power with no load and the speed regulation.
An induction motor of 30 HP, 220 V, 450% of the rated current with therated voltage and delivers during the starting period, with 130 % of the normal torque. The full load efficiency and full load power factor of the motor is 80 and 70 percent, respectively. If an autotransformer is used as a starting unit and the starting torque of the load is only 50 % of the rated torque of the motor, Determine the starting voltage and the starting current of the line.
A 50-kVA, 550-volt single phase alternator draws a field current 10 A at rated load. With the same field current, the open circuit emf and short-circuit currents are 300V and 150A. The ohmic resistance of the armature between terminals is 0.18ohm. The ratio of effective to ohmic resistance maybe taken as 1.5. Determine the regulation at 0.8 power factor lagging. *Well Explained
A 440-V-rms (line-to-line voltage) three-phase induction motor runs at 1150 rpm driving a load requiring 15 Nm of torque. The line current is 3.4 A rms at a power factor of 80 percent lagging. Find the output power, the power loss, and the efficiency.